The door panel has 3 or 4 screws. One behind door pull handle, one underneath the door lock/power window pad, and one maybe around the door release handle. The last two have metal retainer clips that have to be gently pryed up to remove. The door now just relies on J hangers to hold it on. Lift up gently. Remove electrical connectors and you have it off.
To reinstall you must hang the door while ensuring that the manual door lock wire is in its slot and reverse the process.
Be careful when removing any panel with the metal clips. Use wide putty knives or prybars to spread out the stress and make sure u get as close to the clip as possible before you apply pressure. If it still doesn't budge you missed a screw.
The electrical connections usually have simple locking tabs and then you wiggle them apart (sometimes a pocket screwdriver comes in handy). If they have red tabs, you might have to slide them first.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US. click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need. Goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
ok if the wire is not cut open the small triangle panel on side of dash accessible only with door open. there are you will see the harness plugs for the door. check if they are still locked in and or if they have power to them. (note the right door is controlled by the left door,,, check the harness on the driver side and the switch panel on driver side door for a loose or unplugged harness
If the door locks by using the door switch the fault is with the master control unit. So there is a link failure from the master control to the sub units in the door, it can be a break in the wiring harness in the door hinges as this remote trigger can be lost on the driver side and which goes parallel to the rear side.
remove the panel and check the lines, compare to the other side to find the missing line - open wire. You can loop or wire a new connection from the open section.
Instrument Panel Fuse Block The instrument panel fuse block access door is located on the driver side edge of the instrument panel.
Pull off the cover to access the fuse block.
The vehicle may not use all of the fuses shown.
Fuses Usage 1 Rear Seats 2 Rear Accessory Power Outlet 3 Steering Wheel Controls Back light 4 Driver Door Module 5 Dome Lamps, Driver Side Turn Signal 6 Driver Side Turn Signal, Stop lamp 7 Instrument Panel Back Lighting 8 Passenger Side Turn Signal, Stop lamp 9 Passenger Door Module, Driver Unlock 10 Power Door Lock 2 (Unlock Feature) 11 Power Door Lock 2 (Lock Feature) 12 Stop lamps, Centre High Mounted Stop lamp 13 Rear Climate Controls 14 Power Mirror 15 Body Control Module (BCM) 16 Accessory Power Outlets 17 Interior Lamps 18 Power Door Lock 1 (Unlock Feature) 19 Rear Seat Entertainment 20 Ultrasonic Rear Parking Assist, Power Liftgate 21 Power Door Lock 1 (Lock Feature) 22 Driver Information Centre (DIC) 23 Rear Wiper 24 Cooled Seats 25 Driver Seat Module, Remote Key less Entry System 26 Driver Power Door Lock (Unlock Feature)
you may just have a bad connection under the lock button under switch panel on your drivers door. check electrical plug in at door lock switch by removing that panel from driver door.it may be that you have to replace that door lock switch .thers only one fuse for door locks and if pass side works, it's not blown.
hi, does the drivers door unlock and lock all the other doors if it does then you may find that a clip or connecting bar has come off the passenger door lock, you would need to take the door panel off to check,
If how ever the passenger door dont lock and unlock via the drivers door then you would need to buy a new central locking motor for the passenger door..
Your best option would be to remove the passenger side door panel and get someone to lock and unlock the drivers door whilst you look at the passenger side and have a look to see what parts are moving this should then give you a good idea of the parts that could be damaged
driver's door module should have a 12v battery feed..if this missing it could explain your problem..module not being powered up..look between driver's door and body..in harness,you may have broken wiring
You have totake the door panel off to get to the wiring harness. door panel should be held by plastic clips so all you have to do is grab a corner and give a nice tug. First check to make sure there are no screws in it that I may have missed. Remove the clips from the door with a fork and put them in the panel and replace the panel by using a small tap.