Question about 2000 Chrysler Concorde

1 Answer

Can i put a 3.2 engine in place of a 2.7 in my 2000 concorde?

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

It can be done.
You will need another car, the same year as yours, with the engine you want. This is to get all the hose, belts and brackets you will need.
If you hire it done, plan on $2-3,000.00.
There are sites on the internet with the detailed description on how to do it.

Posted on Aug 05, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replacing the thermostat/2002concorde 3.5

It is located under the exhaust on the side of the block at the place the upper radiator hose is attached to the engine.

Apr 02, 2014 | 2002 Chrysler Concorde

1 Answer

Smooth idle until put in gear then acts like its going to die

Is the check engine light or service engine soon light on ?

Feb 03, 2013 | 1997 Chrysler Concorde

1 Answer

2002 chrysler concorde evap cannister location

look engine compartment near cruise control actuator or look fender panel near windshield washer fluid put EVAP CANISTER DIFFERENT PLACES.

Dec 15, 2012 | 2000 Chrysler Concorde

2 Answers

I changed the oil in my 98 concorde and now it wont start. The oil light is on but not the check engine light.\

do you here the fuel pump working when you turn the key?If not could be a fuse that runs the fuel pump.

Aug 05, 2012 | 1998 Chrysler Concorde

1 Answer

In removing harmonic balance on 1996 chrysler concorde 3.3 engine, my chilton repair book states to use a 4" 3 arm puller and a special tool to place in the center of the pulley, I'm have a problem...

Hello, This is also called a gear puller. The best place to find them is at a tool store like sears, harbor fright Farm & Fleet or Fleet farm. I know harbor fright has them causes that's where I got mine. Harbor fright also has a web site online. If you have any more questions feel free to ask me. Good luck

Feb 19, 2011 | 1996 Chrysler Concorde

1 Answer

Where is the thermostat 3.2motor

Follow this upper radiator hose from the radiator to the engine block. There is a cap there that the hose connects to. That is held in place by 2 to 3 bolts or Nuts on studs. The thermostat is under that cap.

Feb 08, 2011 | 1998 Chrysler Concorde

1 Answer

How to remove the starter

Welcome to Fixya

Here's the procedure on how to replace/remove the starter.

Loosen the negative battery terminal on the car and pull the terminal away from the battery. Place the wheel chocks behind the rear tires.

Jack the car using the automobile jack and place a jack stand under the frame near the jacking point. Raise the jack stand to the frame.

Remove the three bolts that hold the starter to the engine using a socket and ratchet. Remove the starter away from the engine so you can gain access to the wires.

Remove the main wire from the starter using a wrench to remove the nut and then unplug the wire harness.

Pull the old starter away from the engine and put the new one into place. Reconnect the wires by plugging the wiring harness back in and securing the main wire back to the post, tightening the nut with a wrench.

Push the starter into place on the engine and start all three bolts by hand. Tighten the bolts using a socket and ratchet.

Remove the jack stand from under the car and lower the car back to the ground. Start the car to test the installation.

Thank you for using Fixya!

Dec 20, 2010 | 1996 Chrysler Concorde

1 Answer

Can't find location of 99 Chrysler Concorde Battery

Look under the left front wheel well you might have to take off the Wheel to get at it its forward of the wheel Stupid place to place to put it isnt it

Dec 11, 2010 | 2002 Chrysler Concorde

1 Answer

99 chrysler concorde 2.7. I just removed the alternator. I can't get it lined up with all 3 holes to get it back on.

put the 2 down bolts half way and then put the serpentingbelt and then put on the third bolt. then loos the tensioner.

thats it XD

Jul 01, 2010 | 1999 Chrysler Concorde

1 Answer

I put a 99 3.2 dodge Concorde engine in a 01

You cannot run an external regulator on this, your only solution is to replace the ECM.

Dec 02, 2009 | 2001 Dodge Intrepid

Not finding what you are looking for?
2000 Chrysler Concorde Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides