Question about 2000 Nissan Quest

1 Answer

Left front brake

Will not release and burns the pads,remove the fuses and have not done it anymore. Put the brake fuses back in and the brake on front left side lock up again. Please help me!

Posted by on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,369 Answers

Replace th eflex hose at the front wheel. it's colapsing inside not letting fluid flow back.

Posted on Apr 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front brake pads on a How to replace front brake pads on a 2000 Chevy S10 4WD pickup?


First you want to remove brake fluid from brake resovoir, raise front wheels off ground and set park brake or block rear wheels. Remove front wheels, keep steering wheel unlocked so you can turn rotors side to side. Loosen bolts that hold caliper end gently pry caliper free from rotor, remove caliper and remove pads, use bungy cord to hang caliper away from rotor, have rotors measured to see if they are thick enough to have machined, replace if out of specs. Match up pads with old ones, use anti- squeak red liquid and put layer on back of pads, let dry. Use tool to put pistons back into calipers, slowly put pistons back into bore while opening up bleeder screw so ABS won't be damaged. After rotors resurfaced, wash with rubbing alchohal to remove any oils from hands, install rotors and reverse putting pads back onto caliper and reinstall, torque caliper bolts to factory specs and tighten bleeder screws. Install wheels, torque lug nuts to factory specs and replace brake fluid in resovoir. Lower car carefully to ground and press brake peddle without pumping it. Any air in system should bleed out, if not get someone to help with bleeding system. Road test to ensure no squeaks or pulling, burn brakes in slowly.

May 10, 2014 | 2007 Saturn Aura XR Sedan

1 Answer

Mazda5 rear right brake gets hot, sometimes smells burning.


Try simple/free things first: put car on jack stands,turn wheels to see if you hear pads/shoes dragging after brake pedal on/off,pads should free-float after brake pedal release and if not releasing (by the way,was any brake fluid spilled accidentally on the pads??),more than likely bad caliper;sure the pads are correct ones (thickness) for your car rotors/calipers???. Hope this helps. Alberto

Feb 10, 2014 | Mazda 5 Cars & Trucks

1 Answer

How do i replace front rotor in 2004 toyota sienna


1. Put your car on a level spot for safety and start your car Sienna.
2. For left front rotor, turn your steering wheel to the left all the way and stop the engine. DO NOT put emergency brake on! Put stopping blocks on the passenger front front, rear right and rwear left for safety.
3. Half loosen all front left tire nuts and jack up the left front then loosen all nuts and take the wheel off.
4. Use a 3" G-clamp from Lowes, Home Depot or any store near you, press against brake cylinder so that brake fluid flows back to its reservoir
4. Remove one bolt on the caliper and the other bolt loosen and lift the caliper with the other bolt on and rest on a block. Do not take the rubber hose off nor attend to loosen any brake fluid pipes and nuts.
5. Remove brake pads and remove the nuts on the rotor, done.
If you need further assitance please let me know and if this assisted you please feel free to rate the solution accordingly. Thanks, Midwest-tek

Aug 31, 2010 | 2004 Toyota Sienna

3 Answers

Smells like brakes are burning


This sounds like a caliper hanging up and not releasing. Are you sure the calipers were replaced? I would take this back to the shop where it was done as you will quickly ruin the new pads and rotors if the calipers are not operating correctly.

Jul 19, 2009 | GMC C1500 Cars & Trucks

1 Answer

Front brakes not releasing properly.


Sounds like the caliper needs replaced. Sometimes the pistons lock in the caliper and cause the brakes to drag. When the mechanic changed the brakes before, he pushed the pistons in all the way to accomodate the new brake pads. Now that they are wearing back down, it is getting to the warped spot in the caliper and starting to stick.

Jun 25, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Brakes are burning up


Check the rubber brake hoses. Many times they internally fail and prevent calipers from releasing.

Jun 08, 2009 | 1991 Buick LeSabre

1 Answer

Front brake pads need to be changed, how?


Jack the vehicle u. Support it on jack stands. Remove front wheels. There are two bolts that hold the brake caliper on. Remove those. use a C-clamp to push the caliper piston back in. Install the new pads in the caliper brackets (pop into place). Put caliper back on, then wheel back on. Put vehicle back on the ground. Press brake until firm. Done.

May 15, 2009 | 2005 Pontiac Montana SV6

1 Answer

2006 dodge ram 2500 4x4 diesel replace brake pads front and back


Straight forward job. Remove wheels, remove 2 caliper bolts per wheel, check bolts,and bushings for wear/corrosion and lubricate, remove calipers, remove brake pads, push caliper pistons into calipers, replace anti-rattle clips, put new pads in, put caliper and bolts in, put wheels on. Start truck and press brake pedal several times to take up slack and you're done.

Apr 25, 2009 | 2004 Dodge Ram 2500

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

No brakes after changing brake caliper & bleeding system


Sounds like you still have air in your brake lines. Make sure all your brake lines are tight. Then bleed again. Bleed the trouble side first, meaning right side, then go to front left, back left then back right, make sure that your brake fluid is also full

Feb 11, 2009 | 2004 Toyota Tacoma

Not finding what you are looking for?
2000 Nissan Quest Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...