Question about 2002 Ford F250 Super Duty SuperCab

2 Answers

Not quite sure how to change my ignition cylinder dont see a push button like other ford models

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 4,369 Answers

Here you go. If this solves your issue, please rate as Fixya. Good luck. Ignition Switch Lock Cylinder —Functional Removal and Installation

  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the ignition switch lock cylinder (11582).
    1. Insert the ignition key and turn to the RUN position.
    1. Using a 1/8-inch drift, press the ignition switch lock cylinder release pin through the access hole while pulling out the ignition switch lock cylinder.
not quite sure how to change my ignition cylinder - 2e15945.gif
  1. To install, reverse the removal procedure.
    • Verify ignition switch lock cylinder operation.
b141ce9.gif

Posted on Mar 06, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 6,674 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove a ignition lock cylinder without a key? on a ford ranger w/tilt steering 1987yr


Be sure and watch the first video. Make sure you understand the mechanics of what you are trying to do, first. The first video link is on a Ford. Its not easy to do, but it can be cheap. Just don't slip up and drill too deep. Fortunately you will have the new cylinder to use as a guage for how deep too drill.
Now what I have done is determine where the pins are that actually lock the lock, and just drill those out. Then you can take a large screwdriver and turn the cylinder. Once turned, you can press the button they are talking about in the video and it will release the cylinder. Then just insert the new one in the same position.
How to change out your ignition lock cylinder when you don't have the key.
Watch the second video to see how to replace the cylinder when you can get the old one to turn.
How To Install Replace Worn Out Sticking Ignition Key lock Cylinder Ford...

Dec 24, 2014 | 1987 Ford Ranger

1 Answer

HOW CAN I CHANGE THE SHIFT KNOB ON MY 2000 FORD EXPEDITION


The shift knob is part of the shifter handle. The overdrive shift button assembly and button cover are replacable seperately. To remove the button, simply pry off the cover, pull out the button and replace. reverse the order to assemble.

To remove the shift handle, remove the ignition cylinder by turning to the run position and pushing a small pin, drill bit or allen wrench into the hole on the bottom of the trim cover hole to release the ignition cylinder. Pull the cylinder out. Next remove the screws from the bottom column trim cover and remove the upper trim. Next, remove the pin from the shifter and disconnect the electrical connector. Replace the shifter and reassemble. Good luck, please ask for more information if you can't leave four thumbs up. Have a great day!

Apr 12, 2011 | 2000 Ford Expedition

1 Answer

I need to know the procedure to reset, 'Change Oil warning' on my 2006 Ford Freestar.


On the right side of the steering wheel there is a button that says "setup". Turn the ignition key to the on position, push the setup button and hold it until the change oil warning shows 100%. There should be a message that pops up telling you to push the reset button to the right of the setup button. Push the reset button and hold until the message confirms the oil life has been changed to 100%. Release button turn off ignition key. Now start the engine to make sure the warning light does not come back on. If it does, try again.

Jan 22, 2011 | 2006 Ford Freestar

1 Answer

How do i remove an ignition cylinder from a 1993 chevy impala??


to remove ignition push pin under cylinder as you turn it there is a pin if you remove the columb caping off it will be quite visable

average charge is 35.00 from lock smith
if you take old cyl and old key to smith they can re key a new cyl for arround 50 -75 bucks

Jan 28, 2010 | 2002 Ford Explorer

2 Answers

How do I change a ignition switch cylinder in a 1995 ford taurus? My ignitions switch is not turning to the off possition and it is leaving the inside lights and radio on and running down the battery. Is...


There should be hole about1/4 inch in diameter in the shroud around the steering column right under the lock. Turn the key to the on position and take long punch or nail and go through that hole and push the release button. The lock assembly can then be pulled out, there's a steel washer down in the hole with a "D" shaped hole in it be careful not to lose that. Sometimes the washer will come out with the lock cylinder. If you can't find the release button you may have to remove the shrouding so you can see what you are doing. Take flashlight and look up in there for the button it's only about an 1/8 inch in diameter. Good luck.

Jan 23, 2010 | 1995 Ford Taurus

2 Answers

If i change my ignition after a break in do i need a new key for the doors and ignition too


If the door lock is undamaged then it's fine to use the old key in the door and the new key with the ignition - you then have 2 separate keys for ignition and door -
I dont quite understand the question... could you word it fidderently,
You said you "changed my ignition" - which parts of the ignition?

Jan 22, 2010 | 2000 Nissan Xterra

1 Answer

Need to replace ignition cylinder on 2000 Impala


Pop off the black ring around ignition lock small screwdriver willl do. Remove dashboard plastic to expose 2 bolts holding ignition assy. Can be tedious. IF you can turn the key turn it to Start. In the plastic housing there's a 1/4 by 3/8 hole. push in a screwdriver which will push in a button on ignition cylinder and allow you to slide it out. The hole is located at 4 o'clock if we agree that the 2 wiring harness plugs are at 6 o clock and its 1 and 1/4 inches below the face of ignition cylinder. If you dont feel that the screwdriver is pushing in that "button" rotate your key until it does. Then just slide the cylinder out.

Mar 20, 2009 | 2000 Chevrolet Impala

2 Answers

Ignition switch in a 1995 ford taurus


Ignition Lock Cylinder
Ford Taurus/Sable 1986-1995 Repair Information grey_line.gif

clearpixel_002.gif clearpixel_002.gif lower_right.gif

clearpixel_002.gif

REMOVAL & INSTALLATION

Functional Lock


The following procedure applies to vehicles that have functional lock cylinders. Such cylinders either have a key available or known key numbers from which a key can be made.
  1. Disconnect the negative battery cable.
  2. Turn the lock cylinder key to the RUN position.
  3. Using a 1/8 in. (3mm) diameter wire pin or a small drift, depress the lock cylinder retaining pin through the access hole in the upper steering column shroud (under the ignition lock cylinder) while pulling out on the lock cylinder. Remove the lock cylinder from the column.

Using the key, turn the ignition lock cylinder to the RUN position, then depress the retaining pin using a wire pin or small drift

To install:
  1. Install the lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the lock cylinder into its housing. Make sure the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the cylinder retaining pin to extend into the cylinder housing.
  2. Rotate the lock cylinder using the lock cylinder key, to ensure correct mechanical operation in all positions.
  3. Connect the negative battery cable.

Non-Functional Lock
The following procedure applies to vehicles in which the ignition lock is inoperative and the lock cylinder cannot be rotated due to a lost or broken key, unknown key number or a lock cylinder cap that has been damaged and/or broken to the extent that the lock cylinder cannot be rotated.

Jan 27, 2009 | 1995 Ford Taurus

1 Answer

My ignition switch is broken


this is a common ford ignition cylinder problem.you can buy a new key cylinder at a checker or autozone cheap.remove column cover and push small metal button and cylinder comes out

Jan 17, 2009 | 2001 Ford F250 Super Duty Super Cab

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

349 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...