Question about 2001 BMW Z3

1 Answer

Drive train on 1997 Z3

Clutch allow car to go in gear, but dose not ingage

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Sound like your clutch disc ran out you need to change you clutch.

Posted on Mar 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My daf cf85 is not ingaging any gear what's the problem


run the fault codes
possible clutch control module not allowing clutch operation
get a service technician in

Jul 15, 2016 | DAF Cars & Trucks

2 Answers

1997 Saab turbo (manual) won't move in gear


You will need to tear it down and inspect the drive train components for broken parts.

Jun 06, 2012 | 1997 Saab 900

1 Answer

Standard shift, v6, 3.2, and can't ingage shifter into gear. Replaced slave cylinder and master cylinder. Bleed unit, after starting it looses pressure on clutch pedal not allowing gear to ingage. With...


Sounds like you may have air trapped in the system.Try this trick.Remove the bleeder screw from the slave cylinder.Place your finger over the hole to act as a one way valve, allowing air and fluid to escape but not allowing air to get sucked back in.Then have someone stroke the pedal slowly making full strokes, keep an eye onn the resevoir so that it does not get low and fill the system with more air.If there is room turn a bottle of brake fluid upsidedown in the resevoir to keep it from running dry.After you have run a bottle of fluid through it replace the bleeder and pump and bleed the old fashioned way a few times.If there is air it should be gone.If clutch will still not disengage the something is wrong with clutch plate and or pressure plate.Good luck!

Mar 02, 2011 | 1992 Isuzu Trooper

1 Answer

I just bought a 1997 BMW Z3 1.9 engine 5 speed, It is very hard to shift into all gears, if I push it all the way to the floor hard it gets easier but still sort of hard, is there a adjustment for the...


you have a bought a car with a worn out clutch end of story ,so take gearbox out and then take old clutch in hand to auto factor so you get the right clutch first time then fit it and you will have a nice car ,the clutch is hard to push down because the diaphramn spring in the pressure plate is working overtime because the clutch disk is worn to excess .not too difficult on this rear wheel drive car though just dirty work

Feb 26, 2011 | BMW Z3 Cars & Trucks

1 Answer

When driving yesterday in 4th at 60km the engine starting reving very fast and would not ingage in any gear, blackish / grey smoke was poring out the exhaust, it would not ingage in any gear and I turned...


Tell your mechanic to check for damage radiator trans cooler, sometimes the coil cracks allowing transmission fluid mix with coolant, and coolant with transmission fluid creating lots of present and future problems.

Dec 26, 2010 | 1993 Toyota Land Cruiser

1 Answer

Put car in reverse after car warms and it doesnt ingage until you push on the gas. It stays in the nuetral position


hi sound like the clutch is worn and your having to use the speed of the engine to help you ingage the gear.Does the clutch slip at all when driving in a forward gear ?

Sep 02, 2010 | 1993 Saturn SC2

1 Answer

1999 honda prelude manual transmission isn't disengaging all the way when i shift, sometimes locking the shifter in gear or not allowing me to up or down shift. I know my master and slave cylinders need to...


This depends as dose it do it when cold or hot.
2nd when you push in pedal and put in gear dose it go in clean or hard to select 3rd can you hear a grinding noise when pushing in pedal and noise goes
when you take you foot off the clutch pedal IF so then its the thrust bearing on clutch REPLACE ALL .4th if you push in clutch pedal and select a gear and let the clutch out if drive right out (replace)

Sep 27, 2009 | 1999 Honda Prelude

2 Answers

97 jimmy 4wd front differential


theres a ingage and disingage sencer up in there sometimes it gets stuck and it sounds bad but if u bang on it with a hammer sometimes it will let go try that

Dec 26, 2008 | 1997 GMC Jimmy

1 Answer

Manual trans is stuck in 1 gear


This actually happened to me in my '91 taurus SHO. As they towed it off, the driver looked under the car, and noticed the gearshift linkage had slipped off. He reconnected it right there (no tools required other than we had the front of the car lifted off of the ground) and I drove home.

Dec 18, 2008 | 1997 BMW Z3 Roadster

Not finding what you are looking for?
2001 BMW Z3 Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...