Question about 1989 Jeep Wrangler

1 Answer

Jeep hard lower soft upper doors 1989 vs. 1991

I bought hard half doors from a junk yard and it came with the soft uppers. The doors fit ok but the uppers there is a gap between the windshield frame and the door. Does the 1991 window tilt back more than the 1989 or do are all the windows adjust to fit differant tops?

Posted by on

  • Keith Lett Mar 13, 2009

    Never would have thought there was extentions on the roll bar under the covers. Nice! Thank you very much.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

To make this adjustment you have to loosen the 3 bolts that hold the windshield frame to the dash and the bolt that allows for adjustment in the rollbar extensions. This will allow you to push the windshield forward or backward to close the gap. then tighten everything back up!

Posted on Mar 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW DO I FIND SHOCK ABSORBER STRUTS AND UPPER AND LOWER CONTROL ARMS FOR MY DIAMANTE V6 DIAMANTE


Hard to find parts for a Damante, I'd call around junk yards for the control arms. You can probably find an aftermarket replacement for the struts at a parts store. Take them with you so you can find a reasonable facsimile.

Jan 07, 2015 | Cars & Trucks

1 Answer

I have a 1995 jeep wrangler rio grande with a 2.5 4 cylinder engine that has blown up, I found a 1991 engine from a junk yard, will it fit in my 1995 model.


No..you can't downgrade,the sensors will be different . The older engine might not have knock sensor.check with a salvage yard they have cross reference books that will let you know if it's possible

Oct 31, 2013 | Cars & Trucks

1 Answer

Drivers door / standard cab / log wheel base / C1500 appears to be sagging and locking mechanism is heavily striking on frame "bar" attachment. Looking for way to adjust door.. Door hard to open from...


There is no adjustment for these door hinges. With the door open wiggle the door up and down and inspect the door hinges while doing so. I suspect that you will find the upper hinge is bad. These can be had at most junk yards or through a dealer. The dealer depends on if they still support that truck anymore.

Aug 03, 2010 | 1989 Chevrolet C1500

1 Answer

I recently purchased a 1995 wrangler Rio Grande and the soft was replaced with a factory Mopar hard top and the soft upper doors are not a fit. They have sharp angled corners where the hard top has...


Contact Jeep and see if they have such a thing. If they dont then you will have to take it to a fabricator that can custom alter your doors for you.

Mar 30, 2010 | 1995 Jeep Wrangler

1 Answer

I have a hardtop with lower half hard doors. Can I use soft upper half doors with this hardtop?


no you cant for say the doors on the hard top are a little diff but you can use them to get buy if need be they just wont seal along the top rear

Oct 22, 2009 | 1991 Jeep Wrangler

1 Answer

Rear seats for 98 Windstar


aerostar and early 95 windstar as well as 99 & up dont fit but can be modified to fit. your best bet is go to a junk yard because the rear seats are a dime a dozen. all the upper parts are the same but the lower steel parts are slightly different

Oct 13, 2008 | 1998 Ford Windstar

1 Answer

Hard top wiring


I'm guessing that the top and Jeep are 2 different years.
You need to go to a salvage or junk yard to find the same plug and cut the other one off and splice in the one you buy from the junk yard.

Oct 13, 2008 | 2003 Jeep Wrangler

2 Answers

1991 nissan maxima


I just went thru this on mine... it is easiest to get to from the bottom right corner... remove the shields and it's right there... take the lower adjustment bolt out , the upper rear bolt and the upper outer bolt out , drop it down and swap wires and replace . Tip; a shorty phillips screw driver works well to allign the holes on the upper rear bolt. DO NOT tighten any of the bolts untill they are all in.

Jul 21, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...