Question about 1996 Lincoln Town Car

1 Answer

Heater core - 1996 Lincoln Town Car

Where can I get a diagram or instructions on how to remove the heater core on a 1996 Lincoln Town Car.

Posted by on

  • 2 more comments 
  • Anonymous Mar 23, 2009

    This is very helpful but there is nothing like a picture to show you how

  • Anonymous Mar 27, 2009

    need to by pass heater core till i can afford to replace it. HOW/

  • Anonymous Mar 16, 2014

    where is the o2 sensor on a 1996 Lincoln Town car please

  • Anonymous Mar 17, 2014

    how to diagnose problems when the check

    engine light comes on on a 1996 Lincoln Town Car

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 333 Answers

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove and replace heater core on a 1996 lincoln town car, signature series


Hate to tell you this, but you will need to remove the entire dashboard to access the heater core.

Jan 03, 2015 | 1996 Lincoln Town Car

2 Answers

Remove heater core from a 1996 lincoln town car?


are you sure that's the problem? wouldn't want to waste your time. heater core is a time consuming nightmare. you cant learn on youtube

Nov 28, 2014 | 1996 Lincoln Town Car

1 Answer

How to replace heater core


Hi Quinton, I'm glad to help!

Quinton, this is a job that's very hard if you've never repaired cars before. The entire dash must be removed to gain access to the heater box that must also be removed to change out the core. You can google: how to replace heater core on 96 Lincoln town car. This will give you video's on how its done and give you an idea of the work involved. Hope this helps and have an awesome day Quinton.

Mar 05, 2014 | 1996 Lincoln Town Car

1 Answer

Replace the heater core in a 2000 lincoln town car


For heater core replacing procedure.I suggest you to go through this related help links.Its all complete step by step procedure :----How to replace heater core for All car models?

Click the link below:---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

--------------
How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

---------------
How to Remove Heater Core ?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html
Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------
To replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html------How to replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html
----------This will help.Thanks.

Jan 28, 2012 | 2000 Lincoln Town Car

1 Answer

I need to remove dashboard in a '89 Lincoln TC to replace h/core


ouch..this is a big job..if you are not familiar with. can do some damage

Dec 18, 2009 | 1989 Lincoln Town Car

1 Answer

How can I get the diy instructions to replace the heater core in my 1986 lincoln town car.


Haynes manual # 59010. you will have to remove the dashboard to get to the heater core.

Oct 19, 2009 | 1986 Lincoln Town Car

2 Answers

Heater core replacement instructions for a 1999 town car


That is about a 9 hour job. The heater core in in the Heater Air plenum chamber which is behind the dash. the dash has to be removed to replace the heater core. It is an involved job. Lots of bolts, screws wireing connectord and vacume connectors to remove and un plug. Some are behind the inner fender splash guard. The book wants you to remove the complete Heater Air Plenum, But it can be done with Patience and finess.

Oct 07, 2009 | 1999 Lincoln Town Car

1 Answer

Heatr on 96 town car


the heater control valve is located in the inlet heater hose to the heater core under the hood it may be stuck or not opening are of the way.

Feb 07, 2009 | 1996 Lincoln Town Car

3 Answers

93 lincoln town car coolant leak from rear of motor


Instead of removing the intake manifold and the the leaky manifold coolant hose, we simple place a 1" dia hose about 3" long with a **** down it so it can fit around the leaky coolant hose with two hose clamps and an agressive amount of "right stuff" silicone sealant and let stand for 24hrs which should fix the problem

Dec 26, 2008 | 1996 Lincoln Town Car

2 Answers

Needs number for fuse for front heater


Hi
It will be buy your left knee in the little fuse box
Paul

Dec 13, 2008 | 1996 Lincoln Town Car

Not finding what you are looking for?
1996 Lincoln Town Car Logo

2,252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...