Question about 1997 Nissan Quest

1 Answer

I have a 1999 Saab 9-5 Wagon. The keyless entry works on all doors except driver door. The console lock button works the same way. What can I do to fix this?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Lock actuator mounted on the grease lock in the door.. they cost like 75.oo new and is very easy to replace... i would go new for this part since its kinda a pain when you have your arms full... the easiet way to make sure its this part is to manually lock the door with your key and see if will even lock.. if it will then sure enough its this part. thanks aaron!

Posted on Aug 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 saab 9-3 driver's side door will not lock


Sounds like the linkage came off, remove the door panel and inspect

Feb 09, 2013 | 1999 Saab 9-3

2 Answers

How do i reprogram keyless entry codes


door pad keyless codes?

in owner manual, enter permanent code and then press "1" and enter personal code, then press "1" again. Then both codes will work.

If you don't have manual, go to Motorcraft.com and click on technical resources and click on your year owner manual.

---------------------------------------------
Each vehicle equipped with a keyless entry keypad is programmed with a five-digit entry code. This code is provided to the customer through a wallet card in the Owner Literature package. In addition, this code is available through a diagnostic tool and is also printed on the vehicle security module label. When entering codes each digit must be entered within five seconds of the previous button press.
Programming/Erasing Personal Code
A unique personal five-digit code can be programmed by following these steps:
  1. Enter the factory set five-digit code (the keypad will illuminate when pressed).
  1. Press 1/2 within five seconds of Step 1.
  1. Enter the unique five-digit code.
The personal code does not substitute for the permanent factory set code. Either code can be used to access the vehicle. In addition, if a second personal code is programmed, it will simply overwrite the previous personal code. To erase a personal code, carry out the following procedure:
  1. Enter factory set five-digit code.
  1. Press 1/2 within five seconds of Step 1.
  1. Press 7/8 and 9/0 at the same time within five seconds of Step 2.
The system will now only respond to the factory set code.
Anti-Scan Feature
To provide added security, the keyless entry pad is disabled for one minute after 35 button presses without a valid entry code being entered. The keypad will flash during this one-minute mode with all functionality disabled except for 7/8 and 9/0 still being allowed to lock the vehicle.
Anti-Scan will be turned off after any of the following events:
  • one minute of keypad inactivity
  • the keyless entry remote transmitter UNLOCK button is pressed
  • the ignition is turned to the ON position.
Unlocking the Doors with the Keyless Entry Keypad System
To unlock the driver door, enter either the factory set code or the personal code (each digit must be pressed within five seconds of the prior digit). The interior lamps will illuminate.
To unlock all doors, enter either the factory set code or the personal code (driver door unlocks) and press the 3/4 control within five seconds.
Locking the Doors with the Keyless Entry Keypad System
It is not necessary to enter the factory set or personal code prior to locking all doors. To lock all doors, press the 7/8 and 9/0 controls at the same time.
Inspection and Verification
  1. Verify the customer concern by operating the system.
  1. Visually inspect for obvious signs of mechanical or electrical damage.

Dec 01, 2009 | 2004 Ford F350

3 Answers

LHJ001 WIRING


I have the 1995-97 Lincoln Continental Alarm, Remote Starter, Keyless Entry Wiring, review it:

b94b6e9.png


Hope helped.

Oct 30, 2009 | 1996 Lincoln Continental

1 Answer

Keypad door lock does not work..?


it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
  • Enter the permanent factory code.
  • Enter the owner's alternate code.
To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad .
  1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
  1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
      • 9/0 — no memory recall
      • 1/2 — memory seat position 1
      • 3/4 — memory seat position 2
      • 5/6 — memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.
---------------------------------------------
  • Keyless Entry Keypad Does Not Work Properly
  • Circuit.
  • Keyless entry keypad.
  • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • Oct 04, 2009 | 1995 Lincoln Town Car

    2 Answers

    Program fob


    Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
    1. Close all the vehicle doors.
    2. Insert the ignition key into the ignition lock cylinder.
    3. Press and hold the DOOR unlock switch.
    4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
    5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
    6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
    7. Repeat the previous step to program up to four transmitters.
    8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
    9. Operate the transmitter functions in order to verify correct system operation

    Apr 19, 2009 | 1999 Chevrolet Silverado 1500

    2 Answers

    1999 lincoln con


    SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
    1. Enter the permanent factory keyless entry keypad code.
    1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
    1. Enter the new five-digit keyless entry keypad code.
    1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
    1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
    1. After all new keyless entry codes are programmed:
      • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
      • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
      • -------------------------------------------------------------
    Programming —Transmitter
    1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
    1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
      Press any button on the transmitter to be programmed.
    1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
    1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
    --------------------------------------------------
    Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
    1. Press the SET button on the driver door panel.
    1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
    1. Press the 1 or 2 memory button on the driver door panel.
    -------------------------------------------------------------
    Programming —Autolock and Horn Chirp
    1. NOTE: This procedure must be completed within 30 seconds.
      Turn the ignition switch to RUN.
    1. Press the UNLOCK button three times.
    1. Turn the ignition switch to OFF.
    1. Press the UNLOCK button three times.
    1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
    1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
    1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
    ----------------------------------------------------------------------------------

    Apr 07, 2009 | 1999 Lincoln Town Car

    1 Answer

    96 sable wagon keyless entry


    Try re-programing the system.
    These are the instructions from the service manual.

    . Turn ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending
    in RUN. Door locks will cycle to confirm programming mode.

    2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
    to confirm programming.

    3. Within 20 seconds, press any button on second keyless remote. Door locks will
    cycle again to confirm programming.

    4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

    Mar 02, 2009 | 1996 Mercury Sable

    2 Answers

    Keyless entry and door locks


    Do you have he owners manual? instructions are in there for the keyless entry system. If not go to this link:

    http://www.motorcraftservice.com/pubs/content/~WOTEXP/~MUS~LEN/41/96expog1e.pdf

    Sep 21, 2008 | 1996 Ford Explorer

    3 Answers

    Keyless entry


    I believe dealer has to re-program the new code.

    Aug 29, 2008 | 2001 Ford Explorer Sport Trac

    Not finding what you are looking for?
    1997 Nissan Quest Logo

    117 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    705 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...