Question about 2004 Nissan Maxima

2 Answers

2005 nissan maxima sunroof won't open

My sunroof won't open or close, however it does go up and down. So i imagine that it is not the motor but possibly the switch. i disconnected my battery to clean the terminals if that has anything to do with the problem

Posted by on

  • Anonymous Apr 19, 2009

    i have a sunroof on my 2004 nissan maxima, but i cant find the button to open it.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Had this problem all you have to do is actually open sunroof with tilt button all the way and then close it with tilt button to reset, then it should work with open switch. If you disconnect battery this happens and you have to reset it this way

Posted on Mar 18, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

How to remove sun roof panel switch 05'maxima

Posted on Jun 30, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 04 Pontiac G6 4 door sedan the sun shade opens up no problem but when I try to open the glass the first one lifts up but that's it the other 3 pieces dont


Power Sunroof System Components
The power sunroof system consists of the following components:
• One tilting glass sunroof panel--For sunroof vent functions
• Three sliding glass sunroof panels, which allow the sunroof to open in sections
• Power sunshade panel--An adaptable panel which is rolled out or rolled in and stored by the sunshade motor/actuator in order to cover or uncover the sunroof glass panels
• Power sunroof switch--A rotary style switch controlling sunroof switch signal inputs to the sunroof motor/actuator
• Power sunshade switch--A momentary press style switch controlling sunshade switch signal inputs to the sunshade motor/actuator
• Power sunroof motor/actuator--Comprised of both the sunroof motor/actuator and the sunroof electronic control module, it is sometimes referred to as the sunroof control module/motor assembly.
• Power sunshade motor/actuator--Comprised of both the sunshade motor/actuator and the sunshade electronic control module, it is sometimes referred to as the sunroof slave module.
Sunroof Motor/Actuator and Sunroof Switch
The sunroof motor/actuator assembly is located at the rear of the passenger compartment, above the rear view window, between the headliner and the roof structure. The sunroof motor/actuator assembly also contains the sunroof electronic control module and the two components are serviced together as a unit.
Battery positive voltage is supplied to the motor/actuator at all times through the 25-amp LAMELLA ROOF fuse located in the rear fuse block. Whenever the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the motor/actuator is also supplied battery positive voltage through the accessory voltage circuit and the 10-amp ROOF/HEAT SEAT fuse which is located in the body control module (BCM). The sunroof motor/actuator is grounded through splice S403 to body ground G302.
The sunroof motor/actuator supplies voltage to the sunroof switch through three internal resistors and three hard wire circuits. The 3 hard wire circuits are:
• Sunroof switch data 1 signal circuit
• Sunroof switch data 2 signal circuit
• Sunroof switch data 3 signal circuit
The sunroof switch, which is also grounded to G302, is a rotary style switch. When the switch control lever is turned in a rotational direction, the appropriate switch contacts and signal circuits for the selected mode are simultaneously opened and/or closed to ground in order to provide the appropriate combination of voltage signals to the sunroof motor/actuator. The sunroof motor/actuator interprets the signals, and then applies battery positive voltage and ground to the appropriate circuits of the integral power sunroof motor in order to move the sunroof glass panels. At the same time, the sunroof motor/actuator sends a serial data message, via the keyword 2000 serial data circuit, to the sunshade motor/actuator to open the sunshade panel in conjunction with the sunroof glass. As the sunroof glass panels slide rearward to the open position, the sunshade motor/actuator simultaneously rolls in the adaptable sunshade panel.
The sunroof switch is mounted in a bezel which is located above the rearview mirror.


Circuit/System Description
The sunroof system is controlled by the sunroof switch and the sunroof control module/motor assembly, which is also known as the motor/actuator assembly.
The sunroof control module is supplied battery positive voltage at all times through the 15A SUNROOF fuse located in the rear fuse block. Whenever the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the module is also supplied voltage through the accessory voltage circuit and the 10-amp ROOF/HEAT SEAT fuse located in the body control module (BCM). The sunroof control module is grounded through the ground circuit at G302.
The sunroof control module supplies voltage to the contacts of the sunroof switch through the sunroof switch close signal circuit and the sunroof switch open signal circuit. The sunroof control module also supplies ground to the switch contacts through the sunroof switch low reference circuit. When the switch is operated, the contacts and signal circuit for the selected mode are closed to ground, the voltage is pulled low in the module, and the appropriate signal is recognized by the control module. The control module then internally applies battery positive voltage and ground to the appropriate circuits of the reversible power sunroof motor in order to move the sunroof glass panel to the open, close, or vent


Do you know how to do electrical testing ?
Circuit/System Testing
Ignition OFF, disconnect the harness connector at the sunroof control module.
Ignition OFF, test for less than 1.0 ohm of resistance between the ground circuit terminal 1 and ground.
? If greater than the specified range, test the ground circuit for an open/high resistance.
Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 3 and ground.
? If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.
Verify that a test lamp illuminates between the B+ circuit terminal 6 and ground.
? If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
Connect the harness connector at the sunroof control module.
Ignition OFF, disconnect the harness connector at the sunroof switch.
Ignition OFF, test for less than 1.0 ohm of resistance between the low reference circuit terminal B and ground.
? If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, test or replace the sunroof control module.
Ignition ON, test for B+ between the signal circuit terminal C and ground.
? If not the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the sunroof control module.
Test for B+ between the signal circuit terminal A and ground.
? If not the specified value, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the sunroof control module.
If all circuits test normal, test or replace the sunroof switch.

Oct 13, 2017 | Pontiac Cars & Trucks

1 Answer

Sunroof does not open. Fuse is ok and the shade operates normally.


Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Feb 10, 2017 | 2010 Buick LaCrosse CXS

1 Answer

2006 Chevy Envoy Denali moonroof stuck open manually close


You mean GMC not Chevy ! Chevy doesn't make the Envoy . There is no way to manually close the sunroof !
Power Sunroof Inoperative
If voltage is not measured on the sunroof switch open signal or sunroof switch close signal circuits, the fault could be in the retained accessory power (RAP) supply voltage circuit, battery positive voltage circuit, or sunroof motor ground circuit. If the sunroof motor is not being powered, neither will the sunroof switch signal circuits.

2

Attempt to operate the sunroof through its full range of functions in order to verify that the power sunroof inoperative fault is present.
Does the power sunroof system operate normally?
--
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
YES - Go to Step 3

3
Is the sunroof in the fully closed position?
--
YES - Go to Step 4
NO - Go to Step 7

4
  1. Disconnect the sunroof switch.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a 3-amp fused jumper wire to the low reference circuit of the sunroof switch harness connector.
  4. Connect the other end of the 3-amp fused jumper wire to the sunroof switch open signal circuit of the sunroof switch harness connector, for 3 seconds.
Did the sunroof open?
--
YES - Go to Step 17
NO - Go to Step 5

5

  1. Disconnect the 3-amp fused jumper wire.
  2. Measure the voltage from the sunroof switch open signal circuit of the sunroof switch harness connector to the low reference circuit of the sunroof switch harness connector.
Does the voltage measure near the specified value?
B+
YES - Go to Step 13
NO - Go to Step 6

6

Measure the voltage from the sunroof switch open signal circuit of the sunroof switch harness connector to a good ground.
Does the voltage measure near the specified value?
B+
YES - Go to Step 14
NO - Go to Step 10

7
  1. Disconnect the sunroof switch.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a 3-amp fused jumper wire to the low reference circuit of the sunroof switch harness connector.
  4. Connect the other end of the 3-amp fused jumper wire to the sunroof switch close signal circuit of the sunroof switch harness connector, for 3 seconds.
Did the sunroof close?
--
YES - Go to Step 17
NO - Go to Step 8

8

  1. Disconnect the 3-amp fused jumper wire.
  2. Measure the voltage from the sunroof switch close signal circuit of the sunroof switch harness connector to the low reference circuit of the sunroof switch harness connector.
Does the voltage measure near the specified value?
B+
YES - Go to Step 15
NO - Go to Step 9

9

Measure the voltage from the sunroof switch close signal circuit of the sunroof switch harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 14
Go to Step 10

10

  1. Disconnect the sunroof motor harness connector.
  2. Measure the voltage from the battery positive voltage circuit of the sunroof motor harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 11
Go to Step 19

11

Measure the voltage from the retained accessory power (RAP) supply voltage circuit of the sunroof motor harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 12
Go to Symptoms - Computer/Integrating Systems in Computer/Integrating Systems

12

  1. Turn OFF the ignition.
  2. Measure the resistance from the ground circuit of the sunroof motor harness connector to a good ground.
Does the resistance measure less than or equal to the specified value?
5 ohms
Go to Step 16
Go to Step 20

13

Test the sunroof switch close signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

14

Test the sunroof switch low reference circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

15

Test the sunroof switch open signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

16

Test the appropriate sunroof switch signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

17

Inspect for poor connections at the harness connector of the sunroof switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 21

18

Inspect for poor connections at the harness connectors of the sunroof motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 22

19

Repair the short to ground or open in the sunroof motor battery positive voltage circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 23
--

20

Repair the open in the sunroof motor ground circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 23
--

21

Replace the sunroof switch. Refer to Sunroof Switch Replacement .
Did you complete the replacement?
--
Go to Step 23
--

22

Replace the sunroof motor. Refer to Control Module References in Computer/Integrating Systems.
Did you complete the replacement?
--
Go to Step 23
--

23

Operate the system in order to verify the repair.
Did you find and correct the condition?
--
System OK
Go to Step 2

Jul 31, 2016 | Cars & Trucks

3 Answers

Sunroof won't close


see the diagram attached and fix it. God bless youaa64eb51-7e11-4e93-a5bc-68a552df4913.jpg3d325aa6-02b4-4a16-b487-b8a581cd3d55.jpg

Jul 15, 2013 | 2002 Toyota Camry

1 Answer

Sunroof stuck in tilted open position altho motor has power


it probly cam off track if u can get something in there to push it along a little it will probly go down

Feb 27, 2013 | 1999 Oldsmobile Intrigue

1 Answer

2005 nissan altima sunroof


I would check my fuses, then look at the switches and it may end up being the electric motor its self. Hope this helps Chris

Jan 06, 2013 | 2005 Nissan Altima 2.5

1 Answer

Sunroof won't close


Hey Paul, there are limit switches integrated into the motor on your sunroof, usually if it stops completely its because it detected a restriction, such as leaves, or dirt, if there are no visual sign then with the key on hold the switch to the full open position for 10-12 sec then hold it in the close position for the same, cycle the key and see if it reset. The motor can fail as well but it's not very common.. Do u hear any clicking from the motor area when this occurs, also check all fuses to be safe as well,..

Jun 09, 2012 | 2006 Lincoln Mark LT

1 Answer

Sunroof on 1998 chevy cavalier z24 won't close all the way


It can be faulty motor or loose wiring issue or faulty /weak sunroof controlling switch or there is some blockage for sunroof to come down to close or sunroof out of its track the headliner is out of its way.There re many possibilities.All this basics needs to be checked.For further troubleshooting,go through this help link:----
Click the link mentioned below:------
How to Manually Close the Sunroof ? http://howtobyme.blogspot.in/2012/05/how-to-manually-close-sunroof-on-2001.html

-------------
Sunroof Stuck open? http://howtobyme.blogspot.in/2012/05/2001-lexus-is300-sunroof-stuck-open.html

----------
How to manually close Sunroof on Navigator? http://technoanswers.blogspot.com/2012/01/how-to-manually-close-sunroof-on-2000.html

----------
This will help.
Thanks.

Jun 05, 2012 | Chevrolet Cavalier Cars & Trucks

2 Answers

My 1995 nissan maxima has a sun roof that will not close any more than half way. how do i get it shut? im not concerned with reopening it, just getting it closed. thank you in advance.


I have a maxima 1996 and when I lock doors with fob control, and sun roof is open, it will close along with doors. Try this way. Also check fuses under dash and sunroof relay.

Jun 17, 2010 | 1995 Nissan Maxima

4 Answers

Electric sunroof stuck open can it be closed manually


THE ELECTRIC DRIVE SYSTEM FOR POWER SUNROOF IS NOT ADJUSTABLE.DONT REMOVE THE SUNROOF MOTOR UNLESS THE SUNROOF IS COMPLETELY CLOSED.OTHERWISE A NEW MOTOR WILL HAVE TO BE INSTALLED AND TIMED WITH A TOOL THAT COMES WITH THE NEW MOTOR.THE GLASS PANEL CAN BE ADJUSTED.OPEN THE INTERIOR SUNSHADE ALL THE WAY BACK AND OPERATE THE SUNROOF UNTIL FULLY CLOSED.THERE ARE THREE GLASS MOUNTING SCREWS ON EACH SIDE OF THE SUNROOF OPENING.INSIDE THE VECHICLE LOOSEN THE SCREWS SET THE FRONT EDGE OF THE GLASS TO BE JUST 1MM BELOW THE SURFACE OF THE ROOF.ADJUST THE GLASS AT THE REAR EDGE TO BE JUST ABOVE 1MM THE ROOF AT THE REAR TIGHTEN THE SCREWS.

May 23, 2010 | 2001 Pontiac Grand Am SE

Not finding what you are looking for?
2004 Nissan Maxima Logo

2,189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...