Question about 1996 Ford F150 Regular Cab

1 Answer

Clutch stuck I have a 96 Ford 150 reg.cab,4.9 6 cyl.5 speed o/d.On a recent very cold morning while backing out of my driveway the clutch pedal stuck half way.I pushed it back in the driveway and put fluid in the master cyl.Any help you can offer regarding how to bleed the clutch will be greatly appreciated.

Posted by on

  • jag345 Mar 05, 2009

    I'm having trouble with the clutch getting stuck half travel when i let out the clutch on my 96 Ford 150 4.9 w/5 speed.I understand that changing the slave cylinder on this model is difficult because the cyl. is concentric hence; requiring the removal of the transmission.Is this true?Please help-like a lot of folks i have no money and must attempt this fix myself.In anticipation of lots of helpful information I wish to thank everyone in advance--THANKS and Best Wishes God is on our side.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I just changed my clutch fluid and it has been in the teens if not colder my pedal feels very stiff. that is just common when its cold out. on my 96 4.9 300 6.

Posted on Mar 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My clutch is getting stuck and not coming back up when I release it, it's a 2006 Ford Fusion


On the WEB

2006 Ford Fusion Clutch questions - AR15.Com Archive

https://www.ar15.com/archive/topic.html?b=1&f=134&t=1697699
Dec 18, 2014 - 4 posts - ‎3 authors
2006 Ford Fusion Clutch questions - AR15. ... Clutch pedal stops half way up intermittently yesterday. Today stuck on floor. ... With the rope you can get into a pushdown...pull up rythm on the pedal without having to stop to get

Jul 31, 2015 | Ford Cars & Trucks

1 Answer

My clutch pedal on 96 ford 150 not coming back up. it will come up half way


slave cylinder maybe going bad or your fluids are low or a leak some where

Mar 14, 2015 | Ford Cars & Trucks

1 Answer

96 ford 4.9 5 speed hydrolich clutch wont shift all of a sudden new master cylinder


You have a leak and you have air in the system. More than likely the slave cylinder is leaking, the slave is a direct acting one and as with all direct acting slave cylinder it is located inside the transmission bell housing on the transmission input shaft collar. The transmission must be removed to replace it.

Jun 23, 2012 | Ford F150 Cars & Trucks

1 Answer

Manual 5 speed transmission clutch stuck. It was cold. Clutch itself is good. It appears to be a linkage prob of some sort. The haynes manual wont help because it covers too many diff trucks. mine is a 96...


Your truck has a hydraulic clutch, check to see fluid is full in the clutch master cylinder, and see if fluid is leaking at the line or the slave cylinder, line could have broke, or master/slave cylinder needs replaced.

Feb 08, 2011 | 1996 Ford F150 Regular Cab

1 Answer

I pressed on the clutch peddle and it snapped to the floor. Its a 96 ford f-150, 6 cyl. 5 speed stndrd. Throw-out bearing?


check your clutch booster fluid be sure to pull the cup out if fluid is low may be bad slave cylinder

Nov 05, 2010 | 1996 Ford F150 Regular Cab

1 Answer

How to replace the oem clutch master cylinder on a 1988 ford f-150 ,,, where is it located on the truck?,,,


Removal:
1.From inside the cab, carefully pry the clutch master cylinder pushrod and retainer bushing from the pedal cross-shaft lever pin.
2. Disconnect and remove the interlock switch.
3. Remove as much fluid from reservoir as possible and place shop rags under the master cylinder to catch leaking fluid.
4. Disconnect hydraulic line from the master cylinder and plug lines and outlets to avoid contamination and excessive fluid loss.
5. Remove the two nuts retaining the clutch master cylinder.
6. Installation is the reverse of removal exept after installation, bled the system.

Feb 21, 2010 | 1988 Ford F 150

1 Answer

96 F250 cruise control not working


Is the truck an automatic or standard? Commonly the failure has to do with either the brake pedal switch or the clutch pedal switch. What have you checked out so far? Were there any recent repairs? Did your truck make the recall list (check with your local ford dealer), Have you checked for any blown fuses?

Nov 12, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

96 ford f-150 stuck in 4 by 4 low range how can


if this is shift on the fly 4x4(electronic shift),check all fuses first.Try lightly tapping on the 4x4 electric motor on the transfer case,if it changes,replace the 4x4 motor.Water and dirt get in the 4x4 motor,causing it to stick.

Sep 30, 2009 | 1997 Ford F150 Regular Cab

1 Answer

I have A 1998 FORD RANGER EXT. CAB W/ 6 CYL.- 4.0 RECENTLY LOST PEDAL ON MY CLUTCH. REPLACED MASTER CYLINDER, SLAVE CYLINDER, AND THE CLUTCH PACK, HAVE FLUID THROUGH BLEEDER VALVE ON THE SLAVE BUT CAN NOT...


Take the top off the master cyl and slowly very slow push in on the clutch and watch for any bubbles comming up.Replace the top and pump pressure and bleed at the master direct by using the lines for bleeders.

Aug 13, 2009 | 1998 Ford Ranger SuperCab

2 Answers

I have a 5 speed trans on my 1995 f-150 and the clutch won't engage. The engine is a 300 c.i.


The most common cause of this problem is a leaking hydraulic clutch slave cylinder, in order to replace this cylinder u must remove the trans.

Feb 20, 2009 | 1995 Ford F150 Styleside Regular Cab

Not finding what you are looking for?
1996 Ford F150 Regular Cab Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...