Question about 1999 Dodge Intrepid

2 Answers

Location of the camshaft and crankshaft sensors

My car is a dodge intrepid 1999 motor 2.7   it

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Cam sensor is on the driver side, front of the motor, just below the valve covers in easy veiw, just outboard of the water temp sensor and they both share the same wiring harness.  The cam sensor is on the passenger side, actually on the transmission bell housing.  It takes the signal from the flywheel next to the ring gear, about an inch from the engine on the transmission bellhousing.  Accesible from the top and easier if you remove the air filter duct.  Or jack up the front passenger side and easier if you come in from the front and its behind the axel, behind the motor, go up the bell housing, just below crank shaft level.  Go with this first , it tells the comp when to send fuel.  If you're getting spark with a 1381 code and you're choosing between CAM & CRANK, start with this, this is the culprit.  Consider getting it from the dealer.  Good luck.  This is Waverunner70, Hope I could help.

Posted on Mar 05, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The cam sesor is on the top front of the motor in easy veiw. not sure on the crank sensor i had them both changed on my 1999 intrepid

Posted on Mar 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft position sensor on 1997 dodge intrepid


Mounted where the transmission and engine connect. back towards the fire wall

Sep 25, 2016 | 1997 Dodge Intrepid

1 Answer

I have a 2001 dodge intrepid 3.2 motor i need to know where the camshaft sensor is located


Look at top of timing chain cover, above camshaft sprocket location.

Aug 09, 2011 | 2001 Dodge Intrepid

1 Answer

Where is the camshaft position sensor located on a 2003 dodge intrepid?


Down on front bottom of engine block. Follow the spark plug wires to coil packs and ignition module. Then there will be two or three more wires that run from there down to the crankshaft position sensor.

Jan 16, 2011 | 2004 Dodge Intrepid

1 Answer

What does the camshaft sensor look like on98 dodge intrepid 2.7 L


small round magnetic usually found around the crankshaft balancer or side mounted to the camshaft thru the block.

Sep 24, 2009 | 1998 Dodge Intrepid

2 Answers

My engine light came on i took the car to autozone and they told me that it was my camshaft sensor it stops my car from cranking sometimes i have a 2004 dodge intrepid, my thing is where exactly is this...


no this actually has nothing to do with your fuel pump and it is located at the front of the engine up towards the top should have 2 wires from it. it controls the firing of the spark plugs

May 17, 2009 | 2004 Dodge Intrepid

2 Answers

1996 Dodge Intrepid camshaft position sensor circuit malfunction


DO U UNDERSTAND THE MEANING OF "OUT OF PHASE"?? IT IS THE MECHANICAL TIMING OF THE SIGNAL FROM EACH SENSOR TO THE ENGINE CONTROL COMPUTER, WHAT IS THE CODE? ALSO TELL YOUR DAD (NICELY) THAT ATROUBLE CODE DOES NOT ALWAYS MEANS A FAILED SENSOR, ONLY A PROBLEM WITH THE SIGNAL, THAT CAN BE THE WIRING, IT CAN BE MECHANICAL OR IT CAN BE THE SENSOR, MANY POEPLE DON'T GET THAT AND SPEND TON'S OF MONEY CHASING CODES.I HAVE DONE THIS FOR 35 YEARS AND AM SURE OF WHAT I AM SAYING 100%

May 08, 2009 | 1999 Dodge Intrepid

2 Answers

Were is cranftshaft sensor located on 1998 dodge intrepid


The crankshaft sensor is located near the top of the bell housing on the drivers side of centerline, near to the gear box housing.

Feb 24, 2009 | 1999 Dodge Intrepid

1 Answer

I have a 1999 dodge intrepid but sometime does'nt want to start


I recently had the same problem. I have a 1999 Intrepid. I changed the Camshaft position sensor and tha crankshaft position sensor. I haven't had anymore of those problems.

Feb 18, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
1999 Dodge Intrepid Logo

577 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...