Question about 1994 Honda Accord

1 Answer

1994 Honda Accord: Need to pull trouble codes

My 94 Accord Check Engine is on. In the manual it states that i need to use a jumper wire with the wire connector on the passenger side. What exactly is a jumper wire?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Stick a peace of wire in the connector, make sure each end is inside the connector. once you do that you may have to count the blinking light

Posted on Mar 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of transmissionit is in a 94 honda accord and will it work with a v tech motor


Don't have a clue what the trans is but if its same year model then I'd have to say yes but to confirm it go out an buy a repair manual and check there because it will have all the info you need

Sep 07, 2012 | 1994 Honda Accord

1 Answer

I need to check the engine error code on my 1992 Honda accord lx 2 door coupe but cannot find the connector ( which I have to jumper so that the engine light will flash the code). The repair manual says it...


It is a small, long blue plug with two wires, located above the passengers side kick panel among a bunch of other wires. If it has never been used, it will be taped up to that bunch of wires. Just remove the tape and pull the blue plug down and jumper it.

Feb 03, 2011 | 1992 Honda Accord

2 Answers

94 honda accord radiator fans do not work. fuses are good. not sure on how to check relays. i jumped the thermosatt temp sensor so they stay on just did a head gasket job dont want to do that again


the thermostat could be bad ,not opening up to make the flow of coolant threw engine,you have switch on the bottom of radiator unplug the 2 wires with key on jumper the 2 wires if fans come on that switch could be bad or thermostat not opening to let coolant threw system

Dec 18, 2010 | 1994 Honda Accord

2 Answers

How do you read the trouble codes on a 91 honda


Older cars used the OBD 1 system for retrieving codes, check your owners man, for the location of the diagnostic connector under the hood, use a compatible scanner, most newer scanner's have the cable needed for making the connection. Good luck!

Mar 20, 2010 | 1991 Honda Accord

1 Answer

Does a 94 honda accord and a 94 honda civic have the same parts in the engine


nope 1994 honda accord has a 2.2 engine and 1994 honda civic had a 1.5 and 1.6 engines.they are different engines but both are 4 cylinder engines.

Jan 01, 2010 | 1994 Honda Accord

1 Answer

I have a 1992 honda accord that turns off when the check engine turns on


Well you need to pull codes first under the glove compartment their is a connector with 2 wires connect with a jumper wire turn key to on position dont start motor. count the check engine lights. long flashes are 1 short flashes are 2 position so lets say 2 long flashes and 4 short flashes code24 check a manaul or call auto zone for free then go from there

Nov 12, 2009 | 1988 Honda Accord 4 Door

1 Answer

Radio code stock radio 94 honda accord


if you have the serial number for the radio I have the code.I also just went threw this my also was a factory install.I have a 1995 accord

May 30, 2009 | 1994 Honda Accord

1 Answer

Need to pull and reed trouble codes for a 1989 honda


there is a jumper wire on the passenger side kick panel, short this wire with a paper clip and turn your ignition to run, the CEL check engine light will flash the number of the trouble code,
long flashes = 10's
short flashes = 1's
so a code read like this
L<L<L<S<S<S<S<S
would be 35
there will be short pauses between flashes and a long pause between separate codes,
hope this helps

Feb 09, 2009 | 1989 Honda Civic

1 Answer

1994 honda transmission?


Honda uses internally in the transmission,a shift fork,very much like a manual trans,to change from Forward to Reverse,and vice versa.It is likely this fork isn''t moving.The best thing to do is pull trouble codes out of the car,as a malfunctioning sensor or solenoid (they are mounted on the outside of the trans) could cause a problem.Your year Honda is a manual code read,and their is a procedure to follow to get the codes out of the car.Passenger side front kick panel has to be removed,a blue 2 wire connector located,then a jumper wire is used to short the connector out.Insert the jumper wire,then turn the ignition key to the on position,engine off.This puts the car into diagnostic mode.The "S" light,or gear indicator light on the dash will flash a series of numbers,and these are your codes.You have to write down the number of flashes.For example.....2 flashes,followed by 4 flashes would be a code 24.When the codes are pulled,they then have to be looked up on a chart..then the code is diagnosed and repaired.The problem could still be internal,but external causes have to be addressed first.

Aug 23, 2008 | 1994 Honda Accord

Not finding what you are looking for?
1994 Honda Accord Logo

Related Topics:

594 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

64286 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...