Question about 1987 Oldsmobile Ciera

Open Question

87 cutlass cierra gt starter replacement

How to?

Posted by on

  • gcgarner Feb 28, 2009

    how to get out?

  • sandrad57 May 11, 2010

    and what kinda of timing belt does it have

×

5 Suggested Answers

old marine
  • 1472 Answers

SOURCE: 1984 Olds Cutlass Cierra Body Frame matches what other cars.

I'm not sure that they are an exact match, but the equivalent GM vehicles for the Cutlass Ciera were the Chevrolet Celebrity, the Buick Century, and the Pontiac 6000.

Posted on Mar 05, 2009

ourhowse
  • 2007 Answers

SOURCE: How do I change out headlight bulb on 91 olds cutlass cierra

Behind the headlight, you should see the nylon bulb holder. Turn it counter clockwise, about a 1/4 turn, and it should come out. Pull the old bulb straight out, and replace it with the new one. Don't touch the glass part of the new bulb with bare fingers, or you'll be replacing it again. Use cotton gloves or a paper towel. Put the holder back in the headlight, turn it clockwise until it locks.

Posted on Apr 08, 2009

  • 7 Answers

SOURCE: Trying to locate the fuel pump for a 1994 Old cutlass cierra

The fuel pump is located inside the gas tank. You have to remove the gas tank to change it.

Posted on Sep 03, 2009

ftw1952
  • 10319 Answers

SOURCE: i locked my key in my cutlass cierra "94 how do i get into my car

locksmith is needed to open your door with a slim jim

Posted on Jan 16, 2010

duane_wong
  • 6826 Answers

SOURCE: how to replace the ignition on a 1991 oldsmobile

If you mean the ignition lock cylinder:

Ignition Lock Cylinder CAUTION
If the car is equipped with an air bag, do not service the steering column or dashboard components. Extreme danger of air bag deployment exists even with the battery removed! Serious injury could occur. REMOVAL & INSTALLATION Without Air Bag

  1. Place the ignition switch in the RUN position.
  2. Remove the lockplate, turn signal switch and buzzer switch.
  3. Remove the screw and lock cylinder. NOTE: If the screw is dropped on removal, it could fall into the column, requiring complete disassembly to retrieve the screw. To install:
  4. Rotate the cylinder clockwise to align cylinder key with the keyway in the housing.
  5. Push the lock all the way in.
  6. Install the screw. Tighten the screw to 14 inch lbs. (2 Nm) for adjustable columns and 25 inch lbs. (3 Nm) for standard columns.
With Air Bag CAUTION
Before proceeding, refer to Section 6 for information on disabling and enabling the SIR (air bag) system; otherwise, serious injury could occur.
  1. Turn the steering wheel so the vehicles wheels are pointed straight ahead.
  2. Place the ignition switch into the LOCK position to prevent undercentering of the coil assembly.
  3. Disable the SIR system. Disconnect the negative battery cable.
  4. Remove the coil assembly retaining ring, then disconnect the inflatable restraint coil assembly. Let the switch hang freely if removal is not needed. To remove the coil assembly proceed.
  5. Remove the wave washer, then the shaft retaining lock ring with tool J-23653-SIR to push down on the shaft lock. Dispose of the ring, it is not reusable. Fig. 1: Special tool J-23653-SIR or equivalent is required for pushing down the shaft lock to remove the shaft ring 86818085.gif
  6. Remove the shaft lock, then disconnect the canceling cam assembly.
  7. Remove the upper bearing spring, race seat and race.
  8. Position the turn signal to the right turn (up) position.
  9. Remove the multi-function lever and hazard knob assembly. Unfasten the round washer head screw and signal switch arm, along with the turn signal switch screws.
  10. Remove the turn signal switch assembly by unfastening the connector from the bulkhead connector. Gently pull on the harness through the column and disconnect.
  11. Make sure the coil assembly does not become uncentered, this could happen if the centering spring is pushed down letting the hub rotate while the coil is removed from the steering column.
  12. Remove the inflatable restraint coil assembly with the wiring harness from the column assembly.
  13. Remove the wire protector, then attach a length of mechanics wire to the coil terminal connector to aid in reassembly. Then gently pull the wire through the column.
  14. Remove the key from the steering column lock cylinder set, then remove the buzzer switch assembly.
  15. Reinsert the key into the lock cylinder, turn it to the LOCK position.
  16. Remove the lock retaining screw, then the cylinder. To install: NOTE: Make sure all fasteners are securely seated before applying the necessary torque. If you fail to do so, component damage or malfunctioning of the steering column may occur.
  17. Install the lock cylinder assembly, insert the retaining screw, then tighten to 22 inch lbs. (2.5 Nm).
  18. Insert the key into the lock cylinder. Install the buzzer switch assembly. Turn the key to the LOCK position.
  19. Install the turn signal switch assembly wiring harness through the column, let the switch hang freely. Connect the wiring to the bulkhead.
  20. Insert the coil assembly wiring harness through the column letting the coil hang freely. Attach the turn signal assembly with the binding head screws. Tighten the screws to 30 inch lbs. (3 Nm).
  21. Attach the signal switch arm with the round washer head screw, tighten the screw to 20 inch lbs. (2 Nm).
  22. Install the hazard knob assembly and the multi-function lever.
  23. Install the inner race, upper bearing race seat and spring. Attach the turn signal cancelling cam assembly, apply grease for lubrication.
  24. Replace the shaft lock and install a new shaft lock retaining ring. Use tool J-23653–SIR or equivalent to push down on the shaft lock. The ring must be firmly seated in the groove on the shaft. NOTE: Set the steering shaft so that the block tooth on the race and upper shaft is at the 12 o'clock position. The wheel on the car should be straight ahead. Set the ignition switch to the LOCK position, as this will ensure no damage to the coil assembly.
  25. Install the wave washer, then attach the coil assembly, make sure it is centered correctly. Fig. 2: Centering the coil assembly is important in assembling the column assembly 86818086.gif

  26. Attach the coil assembly retaining ring, the ring must be firmly seated in the groove on the shaft.
  27. Gently pull the lower coil assembly, turn signal, and pivot (pulse) wires to remove any kinks that may be inside the steering column assembly. If you fail to do this you can damage the wiring.
  28. Complete assembling the steering column assembly.
  29. Attach the negative battery cable.
  30. Check the functions of the turn signal, make sure it cancels when turned on and the steering wheel is turned.
  31. Enable the SIR system. prev.gif next.gif

Posted on Aug 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace dash lights on a 1993 olds cutlass cierra


You would need to remove the instrument cluster to get to the back side where the bulbs are.

Dec 07, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

95 Oldsmobile Cutlass Cierra, overheated, won't turn over, clicks once


if you someone that no a little mechanic work ask they to put a socket over the bolt on the crank shaft pully to see if it turns ift seems as if you got a bad motor

Sep 22, 2012 | 1995 Oldsmobile Cutlass Ciera

1 Answer

WIRING DIAGRAM FOR 1993 CUTLASS CIERA s


how change the starter for cutlass cierra s

May 26, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

How to replace starter in a 1991 Cutlass Ciera


I had to do mine recently. You have to remove the radiator to make elbow room. Then jack up the car, as the trick is to remove the motor mount, then jack up the motor itself as high as you can get it to go. At that point you should be able to see the starter. That frees up getting to the starter. The rest is easy, no explanation required, it's just figuring out how to get to it that's a bear. Good luck.

Dec 03, 2011 | 1991 Oldsmobile Cutlass Ciera

1 Answer

I can't find the 2 bolts that hold up the starter ona 1994 cutlas cierra s


http://www.autopartswarehouse.com/models/oldsmobile~cutlass_ciera~makemodel.html

http://www.carbodyparts.net/oldsmobile-cutlass_ciera-inventory.html
http://motors.ebay.com/carsandtrucks/Oldsmobile/Cutlass%20Ciera/1994

Jul 08, 2011 | 1994 Oldsmobile Cutlass Ciera

1 Answer

I have a 1993 cutlass cierra that won't start. lots of battery power but nothing happens when you turn the key. New starter was just put in less than a month ago?


locate purple wire on starter, find good ground on frame, check for power when as a friend tries to start. be small wire (purple or gray) on starter. if no power when key turned to start, its not getting ignition signal from relay or switch. try that.

Jan 03, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

1984 Olds Cutlass Cierra Body Frame matches what other cars.


I'm not sure that they are an exact match, but the equivalent GM vehicles for the Cutlass Ciera were the Chevrolet Celebrity, the Buick Century, and the Pontiac 6000.

Mar 05, 2009 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...