Question about 2005 Dodge Caravan

1 Answer

1996 dodge caravan headlight up/down adjustment ?

Have new headlights on 96 caravan. Driverside is low and passenger side is high. need to adjust- how?

Posted by on

  • Anonymous Mar 15, 2014

    02 dodge caravan se have passenger headlight but not drivers side. When on hi beam have passenger but not drivers side.

  • Anonymous Mar 25, 2014

    headlight goes off and then will come back on

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

There are 2 hex screws that one is for adjusting ht and the other is for adjust in and out and they are just inside the hdlt. if you need more advice go to collisionrepairadvice.com

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

I have a 2001 Dodge Grand Caravan.I have 2 new headlights and the drivers side low beam is out and the passenger high beam is out.I replaced the directional arm and everything stayed the same what else...


You may need a shop manual to get thru this.
There is a body computer and a front control module that affects headlights among other things. The front control module has drivers for each light on each side. All of the lights use the same ground so that should be ok.
The headlight switch sends a signal to the module and it controls the lights.

Dec 15, 2012 | 2001 Dodge Caravan

1 Answer

Adjusting headlight on mercedes benz


his Season:What Are Allergies?Tax Time
  1. Home
  2. Car Repair & Maintenance
  3. Car Lights Repair & Maintenance
  4. Adjust Headlights
  5. How to Adjust a Mercedes' Headlights
How to Adjust a Mercedes' Headlights

In the U.S. the type, adjustments, and illumination factors of all automobile lighting devices are regulated by the Federal Motor Vehicle Safety Standard 108. The headlights must function and be adjusted correctly. Your high beams must disperse their beams straight forward and low beams down and to the right while safely providing illumination without too much or too little glare. It is wise to check the headlight adjustment on your Mercedes at least every year. Doing it yourself will save you time and money. It will also make driving safer for you and others you may meet on the road at night. All it takes is time, some basic tools and a little patience.
Other People Are Reading

Things You'll Need
  • ratchet set
  • 1/4-inch screwdriver, at least 8 inches long
  • flashlight (if needed)
Show More Instructions
    • 1 Open the hood and prop it up.
    • 2 Remove components if necessary to allow access to the left/right and up/down adjustment knobs. They are on top of the rear side of the headlight. The upper knob adjusts the beam to the left and right. The lower knob controls up/down adjustments.
    • 3 Park with the passenger side of the car parallel to a solid fence or wall and about four feet from it. When there is dim light or darkness, turn on the lights and use your screwdriver to adjust the up/down knob on the passenger-side headlight until the light beam is parallel to the ground (you can see the beam of light against the surface of the wall).
    • 4 Turn the car so that it faces the wall approximately one car length away. Adjust the up/down knob on the driver-side headlight until it is at the same level as the passenger side headlight. Then adjust both sides until the small groove on top of the beam cutoff is directly in front of the light.
    • 5 Reinstall any components that you removed. Close the hood.
Tips & Warnings
  • This is method is generic for Mercedes models. Some may differ, as there are many models out there.
Suggest item
Related Searches: References
  • Mercedes-Benz Forum
  • fixya.com: Technical Support, Manuals, Troubleshooting and Product Recommendations
More Like This Comments

Apr 05, 2012 | Cars & Trucks

1 Answer

When low beam headlight is on passenger sign is


Try this to eliminate new bulbs for both sides:
With a partner behind the wheel:
PULL out the bulbs one at a time. Keep them plugged in. While you are holding the bulb - have your partner click and HOLD the High Beam Selection. This causes the Low Beam and High Beam filaments to both go on and stay on.
Check both sides this way.
While the bulbs are out, look at the filaments that did not illuminate. Are they broken, bent, or have indications they are burnt out?
You can also change to bulbs (left to right, right to left) and recheck using the above method of holding the high beam selector and checking the filaments.

Jan 04, 2010 | 2001 Dodge Grand Caravan

1 Answer

Chrysler town country 1996 headlight adjustment.how do i do that.they are to low and to high


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 29, 2009 | 1999 Dodge Caravan

1 Answer

How do I adjust the headlights on a 04 caravan


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 08, 2009 | 2004 Dodge Grand Caravan

2 Answers

How to adjust headlights on 2005 dodge grand caravan


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Sep 17, 2009 | 2005 Dodge Grand Caravan

1 Answer

Low beam not work !!


replace the headlight bulbs. Usually when the bulbs blow out the low beam blows out first, but the high beams still work. If you want and need both low and high beams to work then replace the headlight bulbs with brand new ones and I garauntee that both low and high beams will work

Mar 27, 2009 | 1999 Dodge Caravan

1 Answer

2002 nissan xterra headlight is aiming up too high


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Mar 13, 2009 | 2002 Nissan Xterra

2 Answers

Headlight adjustment


the screws for adjusting the headights are right next to the lights, they are phillips heads and are for adjusting the side to side, 
the adjusting screws for the up and down, are on the bottom of the headlights, and they are a small hole in the grill trim, these lights need a pretty long skinny screwdriver with a phillips head

Aug 17, 2008 | 1996 Suzuki Sidekick

Not finding what you are looking for?
2005 Dodge Caravan Logo

970 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...