Question about 1990 Dodge Dynasty

1 Answer

How do I pacth a quater and rocker panel? - 1990 Dodge Dynasty

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Believe it or not, autosupply places now sell replacements, that are sheet metal, already formed to the shape you need for easy installation in this case, and are very reasonably priced for quick low cost repairs. If yoou want to do it on the cheap, rivet them on.

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Going over curb (by accident) lost the bottom of my rocker panel. How do I find a replacement part and what is it called...is it the rocker panel or the rocker panel cover?


It is a rocker cover panel and if it is a fiberglass unit there will be no problem in getting a new one from the spares department. Go to the spares department and say"bit that runs under the doors" and they will know what you are talking about.

Oct 07, 2013 | 2006 Dodge Magnum

1 Answer

Water getting into quater panels near rear hatch on 2000 chevrolet blazer


There are flapper valve drains on the 1/4's, clear them.

Jun 16, 2012 | Cars & Trucks

1 Answer

1994 toyota carolla with big dent on driverside back quarter panel, is it one big piece or is it a quater panel?


Quarter panel , it's quite a job. Ask the body guy to show you your car when he's in the middle of the job.. You will have a better understanding ..

Jan 03, 2010 | 1994 Toyota Corolla

1 Answer

2007 quarter panel


Any body shop has a great big book with those pics in it. Say pretty please.

Jun 15, 2009 | 2007 Cadillac SRX

1 Answer

Where is the pcv valve on a 2001 mercury couagar


4 cylinder or 6?

v-6

The PCV Monitor consists of a modified PCV system design. The PCV valve is installed into the rocker cover using a quater-turn cam-lock design to prevent accidental disconnection. High retention force molded plastic lines are used from the PCV valve to the intake manifold. The diameter of the lines and the intake manifold entry fitting are increased so that inadvertent disconnection of the lines after a vehicle is serviced will cause either an immediate engine stall or will not allow the engine to be restarted.

Dec 05, 2008 | 2001 Mercury Cougar

1 Answer

Front fender removal


Hiya... here's the details of fender removal/installation:
the left-side (same for right-side) fender has 6 bolts attached to the "sidebody" frame.
The bolt location:
3 are on the top fender-easy to find when hood is open,
1 is hidden at the rear of top inner fender-just open the left-front door wide to find it (early equinoxes had foam-like noise absorber material in it, just remove it from underneath fender after the wheelwell liner is removed),
1 bolt is hidden at bottom of front fender area at headlight/bumper area-you need to remove plastic wheelwell liner to gain access,
1 bolt is hidden at bottom of rear fender area where the black plastic rocker panel meets below the fender...
THIS area is probably the most difficult task to do since it requires you to remove a small bolt found on the front of rocker panel behind the front-left wheel then use a flat screwdriver or clip removal tool to pry open the black plastic **clip's 'dime-sized' head prior to pull out the clip's body (it has 8 clips underneath the chassis) then use your hands to grasp the rocker panel underneath, pull it down-toward you...this should do it....USE CARE during rocker panel and clip removal/installation so you don't break the clips!
It also has yellow plastic clips inside the rocker panel (used as a guide during installation into rocker sill holes-use caution not to break it)
**note: early equinoxes had rocker panel clips that you can actually pull it out from the hole, while later equinoxes has 'built-in' clips inside rocker panels that you don't see the clip heads below it due to engineering part design change**
Be sure to exercise care when handing this task!

808b156.jpg

Nov 20, 2008 | 2005 Chevrolet Equinox

1 Answer

Rocker panels


They make rocker panel repair kits, check with a local body shop or check on the internet, use the search wording ROCKER PANEL REPAIR PANELS

Aug 02, 2008 | 1994 Dodge Intrepid

1 Answer

1999 corvette c


Very easily, take off the passenger side tailight (outter) two screws/torque bit. Once you have done that reach in on the inner quater panel you should be able feel the antenna....... (To remove anntenna). From the outside of the anntenna on top where the actual anntenna comes out there is a ring silver or balck. You should be able to twist (unscrew) that ring to loosen the antenna and two more on the in side of quater panel. The anntenna should drop from the inside of the quater panel. Hope this helps!!

For visual instructions go to: #17

http://forums.corvetteforum.com/c5-tech/1817090-the-ultimate-diy-thread-with-pics.html


Aug 02, 2008 | 1999 Chevrolet Corvette

1 Answer

Remove Driver's door and quater panel


Hey you can do it by the following the instruction given in this link:


http://www.autozone.com/addVehicleId,1965001/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c15280038475




PS Dont forget a fixya rating!

Have a good day...

Jul 17, 2008 | 1995 Mitsubishi Diamante

Not finding what you are looking for?
1990 Dodge Dynasty Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...