Where is the fuel pump located at in a 2004 Hyundai XG350?

Greg Bernett

• 2993 Answers
• Posted on Oct 09, 2009

SOURCE: I need to replace a fuel filter for a 2003 hyundai

Please don't forget to rate!!!


NOTE The fuel filter is located underneath the car, near the fuel tank.

1. Before servicing the vehicle, refer to the Precautions section.
2. Relieve the fuel system pressure.
3. Remove or disconnect the following:
   
   Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter

1. Install or connect the following:
   
   Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
   
2. Start the engine, check leaks and repair if necessary.

Testimonial: "great help, thxx "

SOURCE: I need to find the

In 2002 XG 350 it is near the rear wheel drivers side, , You will need to put a rust lubricant on it once or twice a few days a part then you need two wrenches to remove it , . plus some gas will spill out after braking it lose wait till the gas stops..

SOURCE: how to change spark plugs 2004 hyundai XG350

GO TO AUTOZONE.COM

SOURCE: where is the fuel pump relay located on a 1998

Passenger compartment relay box next the ECM
you will see 5 relay
2 to the left & 1 in the middle & 2 to the right

The one in the middle is the fuel pump relay

Greg Bernett

• 2993 Answers
• Posted on Feb 10, 2010

SOURCE: I need 2004 Hyundai XG350L Service/repair Manual

3.5L Engine

Remove or disconnect the following:

1. Negative battery cable
   

• Engine coolant
  
• Water pump pulley bolts
  
• Alternator bolt, loosen only
  
• Water pump pulley and drive belts
  
• Crankshaft pulley
  
• Timing belt cover(s)
  

1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
   
2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
   
3. Mark the timing belt with an arrow showing direction of rotation.
   
4. Remove the timing belt.
   
5. If defective, remove the timing belt tensioner.
   

1. If necessary, install the timing belt tensioner.
   
2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
   
3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
   
4. Align the timing marks of the camshaft and crankshaft sprockets.
   
5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
   
6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
   
7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
   
8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
   
9. Turn the crankshaft two turns clockwise.
   
10. Readjust the sprocket timing marks and tighten the tensioner bolts.
    
11. Install the timing belt covers.
    
12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
    
13. Install or connect the following:
    
    • Timing belt cover(s)
      
    • Crankshaft pulley
      
    • A/C compressor belt
      
    • Water pump pulley
      
    • V belt
      
    • Negative battery cable
      
    • Engine with coolant