Question about 2006 Jeep Commander

1 Answer

Won't start When i turn the key on it won't start and no lights come on the control panel???

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

Start with the obvious...Check to see if the battery is in good condition and has a full charge. Then, check terminal connections at both ends of both cables to make sure you have a good clean connection. (clean means clean on the contact surfaces NOT that they look clean on the outside)

Posted on Feb 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Chev Malibu. Turn key on to start car, won't start. No warning lights on no lights on gauge panel. Radio works, dome light work.


check the ground leg to your engine.. it runs off the neg. battery terminal. will connect to frame and engine.. pull it off, wire brush it put it back.. you radio will work, 'cause it draws much less current, and is grounded in dash.

Jan 11, 2013 | 2001 Chevrolet Malibu

1 Answer

1998 sunfire want start


is the security light lit? try a different key to start.
if no start do the following.
try to start car then let go of key do not turn it off.
wait 15 min for security light to go out.
turn key off wait 5 seconds then try to start again.

the passkey system is not the best design, a little wear on the key and it won't start, if the tumbler wears out it won't start.

Oct 01, 2012 | Cars & Trucks

1 Answer

My plymouth breeze won't start, won't make a sound, but my lights and horn still works , help me.


any real answer yet? did the problem ever get resolved? i have the same problem with my sister's car. too cold to diagnose tonight, but will post the solution probably tomorrow. since the lights and heater works, but ignition and radio arent getting power, my first guess is there's probably a fried fusible link which controls the 2nd accessory power to the ignition switch. will post a solution soon.

Jul 17, 2012 | 1999 Plymouth Breeze

1 Answer

My headlights won't turn on, the yellow driving lights turn on but the headlamps won't. Also the lever that controls bright lights doesn't work but the turn signal and cruise control does.


First check the headlight relay by changing it with one of the same number in the fuse panel.If it checks out ok then you have a faulty headlight switch.

Nov 03, 2011 | 1994 Chevrolet Caprice Classic

2 Answers

Security light blinks car won't start disconnected the battery used a different key still won't start


need to reprogram the security system. turn the key to start position then to run . let the key stay on until the light stops flashing. repeat these steps 3 times then the car should start if there is not a problem with the pass-lock sensor in the ignition switch or the BCM( body control module).

Aug 07, 2011 | 2004 Pontiac Grand Am

2 Answers

Won't turn over when trying to start. All dash lights come on...won't stary if jumped.


check the voltage of the battery,, it should be a little over 12 volts,, if not,, replace it

Jun 13, 2011 | 1995 Chevrolet Blazer

1 Answer

Replaced stock bcm with used. Was reprogramming with the method of turning key to start position (vehicle won't start) then leaving it in the on postition for approx 10 minutes until the theft lock...


A used body control can be used in a vehicle other than the vehicle it was installed in. the body control module when first installed is programmed with the vehicle vin number. the vin number can not be changed was it was written to the BCM. the oprions can be always change in the BCM but not the VIN number. basically the used bcm you have installed has the vin number from the vehicle was installed in, now the vin number in the used BCM doesnt match all the other control modules

Jun 07, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

94 vette won't start,bat good,have org. key,fuses ok,high beam light on lights off,lcd cluster won't light up?


Disconect the battery and ECM for FOUR DAYS then reconect the ECM and BATTERY. Let it sit for another four days without turning anything on. It should start but will run rough for about 200 miles as the ECM relearns the system. I had the same issue and that is what fixed it.

May 14, 2009 | 1994 Chevrolet Corvette

1 Answer

Radio, dome lights and EVIC power problem


I found a paritally blown fuse. When the fuse blew metal pieces ended up partially making contact. After replacing the fuse everything worked great.

Jan 07, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
2006 Jeep Commander Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...