Question about 1994 Hyundai Excel

Open Question

Noise when clutch depressed on 1999 Hyundai excel.

I'm thinking it could be a thrust bearing, what is involved in putting a new clutch and thrust bearing in? Is it neccessary to remove the motor?

Posted by on

5 Suggested Answers

  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

DJ JDG
  • 2 Answers

SOURCE: Clutch replacement details for 1996 legacy GTB

Trust me it is quite an excercise and not worth doing yourself. With the proper tools, a hoist and a my mate who is a Guru Subaru Mech it took 4 hours. Without having done it before and without the Hoist ( which is wha I was going to do initially ) I'd say you wouldn't get much change out of 8 - 12 hours.

Posted on Jan 01, 2009

emissionwiz
  • 70387 Answers

SOURCE: Change front wheel bearings

u will need to remove the brake cailper and the the brake rotor, then the hub retaining nut, that is a large metric nut, the bearing and hub must come off, then u will need to take this hub to a machine shop or the dealer and have the new bearing pressed in.
BCA/NATIONAL Part # 510078 moreinfo.gif {Ball Bearing Bore=1.5354" Outer Diameter=2.9134" Width=1.4173"}
Front Wheel PRICE: $47.99, PART SOURCE: Rockauto.com

3bcf37f.jpg

Posted on Mar 12, 2009

ghost4548
  • 776 Answers

SOURCE: Change front and rear speakers in 1999 Hyundai excel

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 26, 2009

litoshop
  • 298 Answers

SOURCE: how d i change a clutch in a hyundai excel 1994

Hi first lift the car and be sure to secure the car that it wouldn't fall when your under the car, remove the wheels then disconnect the negative cable from the battery remove the axles, remove the transmission mount, remove the starter, remove the bolts around the transmission housing once you remove the bolts use a floor jack and put it under the transmission then use a prior and separate the tranny from the engine and bring the tranny to the floor now you have the clutch expose remove the old clutch and pressure plate and pilot bearing now do the same thing in reverse good luck

Posted on Sep 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recently developed a whinning when I first start to move


Where is the whining noise actually coming from .. engine/gearbox or elsewhere?
A whining/screeching noise could be a drive belt .. such as the belt that drives the alternator.

On a manual car it could be the clutch bearing making the noise until it warms up. Does the clutch make a noise when you depress the pedal? That's the thrust bearing .. the bearing that operates the clutch.

I don't think you have too much to worry about. If you had engine trouble there would be knocks, rumbles and strange noises at all speeds.

A whining noise is usually associated with something spinning/turning .. such as a pulley/idler on a drive belt or a bearing alternator.

Put your mind at rest - get a mobile mechanic's opinion.

Feb 16, 2016 | 2001 Buick Park Avenue

1 Answer

Noise on gearbox when clutch pedal is pressed down


Hi,I know money is sometimes an issu,but realy when you replace the release bearing you should also replace the presure plate and the clutch plate at the same time so that thay all ware in at the same time,all the best.

Apr 28, 2015 | 2008 Opel Corsa 1.6

1 Answer

Gearbox noise


Sounds Like Thrust Clutch Bearing Is On Its Way Out.
You Need To Remove Gear Box Fit New Bearing On Spigot Shaft
Re Fit Gear Box ,While You Have It Out Check Condition Of Clutch

Mar 18, 2013 | Cars & Trucks

2 Answers

1999 1.4 Ford Fiesta: When depressing clutch a very noisy rumbling sound but gear changing as normal. I added some gearbox oil and the noise stopped. Then, just the following day, no resistance when...


Hi There.
sounds like your release bearing has either collapsed or seized, either way you will have to drop the gear box and check it out... should'nt be a problem on a 1999 fiesta. just be careful not to pop a drive shaft and lose the transmission fluic on the floor.
Good Luck

May 03, 2011 | 2007 Ford F

3 Answers

The clutch in my 1983 Chevy truck rattles when I push it in


the thrust (release) bearing is worn, not a big deal in itself as it will last a long time like this, but if the noise annoys you the bearing is very cheap, though to change it means removing or pulling back the gearbox so if the clutch is not new you could replace the whole lot as easily while in there

Jan 14, 2010 | 1983 Chevrolet Silverado

3 Answers

Clutch is noisy,when i depress the clutch the noise goes away


this noise is caused by a noisy clutch throw-out/release bearing, that is the part that presses against the pressure plate and disengages the clutch disk, the transmission must be removed to replace this part, so it is best to replace the clutch assembly at the same time, the labor for both is the same, about 5 hours

Oct 23, 2009 | 2003 Toyota MR2 Spyder

2 Answers

How d i change a clutch in a hyundai excel 1994


We start by removing front Constant Volocity Joints then dropping the transmision to access the cluch assembly then we remove the pressure plate then clutch disk is removed be advized since your replacing the cluck replace hardware too e.g. clips and thrust bearing and pilot bearing to complete the job! good luck!

Sep 02, 2009 | 1994 Hyundai Excel

1 Answer

Humming Noise in the gear box


more than likely a worn bearing in your gear box, if it is every gear i would say input shaft bearing or output shaft bearing, unless it is while the car is stationary then depress your foot on the clutch if it goes away the its the thrust bearing in the clutch, also could be the spiggot bearing which will humm with car stationary clutch in or out. hope i have helped.

May 16, 2009 | 1999 Toyota Corolla

2 Answers

I have a Hyundai excel 97, 5 speed manual, the thrush bearing sleeve is gone, can this just be replaced or do I have to get whole new gear box ? Is there any other model of hyundai gear box that I can use...


Should be able to replace the thrust, or clutch release, or throw-out bearing assy only, (all names i've heard it called over the years )but take a good look at clutch assy, just in case it's time & you want to save yourself R&R transmission twice in a short time.

Dec 13, 2008 | 1994 Hyundai Excel

Not finding what you are looking for?
1994 Hyundai Excel Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...