Question about 1994 Buick Park Avenue

1 Answer

Partial hidden screws on valve cover 1994 Park Avenue 3.8L

I have a small leak on the front valve cover and can not find a way to get to the two front most screws to remove or tighten. How do you remove the plastic spark plug wire router/holder on the front valve cover to gain access to the two hidden screws. There is a outer cover that can be snapped off. The main block that holds and routes the spark plug wires is covering the screws about 1/3 so a socket can not be used unless the plastic block can be removed.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

The are tight but they just slide striaght up if you bust them they are real cheap at auto zone

Posted on Feb 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change left side front marker light 2002 park ave


Should be the same as my lesabre. You have to remove the wheel well cover (black plastic cover in the wheel well). You *might* be able to remove the clips from the front and bend it back far enough to reach in to remove the bulb. The clips are easy to remive. Using a flat screw drive, small pliers or a trim removal tool pull the center pin back about 1/4 inch. This release the ears on the pin and you should be able to pull the entire clip out.

Jul 06, 2016 | 2002 Buick Park Avenue

1 Answer

Anti freeze on top of valve cover


Bad news!!! Blown head gasket. Sorry

Apr 02, 2014 | 2000 Buick Park Avenue

1 Answer

I am looking for a "backup light cover"? for my


Pliz try ebay or online junkyarddog.com or junkyardparts.net, its not gonna be easy but can be found. Good luck.

Jun 11, 2011 | 1994 Buick Park Avenue

2 Answers

1994 Buick Park Avenue will turn but won't start. They say it's an ICM Code. Can someone other than a mehanic put it in?


Yes. will sit under the coil pack's, that's where the spark plug cable hook to coming from the spark plug's, sit on top if engine, easy to get to, remove all three coil pack, two small screw's to each coil pack, disconnect harness to ICM will have about 26 small wires on the connector, connector will have a small bolt, in center of harness connector, unscrew small bolt and harness will come out, revese to install new ICM.

Jul 19, 2010 | 1994 Buick Park Avenue

2 Answers

How to install a new top and bottom hvac heater hose fitting for a 2002 buick lesabre custom


The hoses are moved by turning them a few degree's, then pulling them off. See diagram below.

658aa5f.gif

Jun 19, 2010 | 2002 Buick LeSabre

1 Answer

1994 Buick Park Avenue The outside temperature sensor


Open the hood

Find the "hood spring", sticking up from the frame in front of you

The sensor is located almost directly below that spring, about two feet down on a bracket that runs vertically from the bottom of the frame where the spring is mounted.

It's easy to replace, with a simple connector and a couple screws.

Oct 18, 2009 | 1994 Buick Park Avenue

1 Answer

How do you remove the rear view mirror from mount.


Is the mount made of metal or plastic? In either case, it will be attached to a "base" that is glued to the windshield. A metal mount should have a tiny little screw in it that pins it against the base. Loosen this crew and the mount should slide upwards (towards roof) off the base. A plastic mount should have a tab that you can pull on and slide it off upwards....

Aug 10, 2009 | 1994 Buick Park Avenue

1 Answer

I have 94 buick park avenue how many screws hold


5 hold it in 3 in the front 2 in the back

Jun 30, 2009 | 1994 Buick Park Avenue

1 Answer

Passenger door panel


The panel is pinned unto to door but there are some hidden screws that have to be removed first. I think one is under the window switch panel and ohe should be around the arm rest. Don't be to conerned if some pins break that happens to us pros all the time.

Sep 29, 2008 | 1994 Buick Park Avenue

Not finding what you are looking for?
1994 Buick Park Avenue Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...