Question about 2005 Chevrolet Suburban

1 Answer

Chevy Subruban 2007 remote control

I change the remote control battry, since than the remote did not work with me, is there away to re program the remote control again.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

You will have to take it to a chevy dealer to have it reset...

Posted on Feb 28, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Key fob

Walk out to the vehicle with a new battery in the key fob and press the lock AND unlock button at the same time while you stand close to the vehicle for 7 seconds. You will hear the doors go thru a lock and unlock cycle, your fob is now programmed. This will sync existing programmed controllers, security sync. to program new remotes:In the trunk, connected to the wireless remote controller (driver side on wheel well, need to remove 'mat') is an empty connector with 2 wires connected. short the two connector pins. The locks will all cycle. Press and hold lock/unlock buttons on remote until locks cycle on/off. repeat for other remotes. Remove short across connector pins. Test new remote(s).Warning:existing remotes are deprogrammed, only remotes programmed will work from now on.This worked on my 1998 Cavalier. Be sure battries in new remote(s) are good! Answer Locate the data link connector under the dash (under the steering column). Ground out pin #8 of the DLC (top right port) with a jumper wire to any piece of metal close by (I use the e brake hardware). The door locks will then lock & unlock to let you know you are in the programming mode. Simultaneously press & hold the lock & unlock button on one of the keyless entries until the locks cycle (this lets you know the transmitter has been programmed). Repeat this step for your second transmitter. You must reprogram the 2nd transmitter within 60 seconds of programming the 1st one or you have to start over.

Read more:

Jun 03, 2012 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Our keyless remote stoped working on our 2007 chevy impala. we put a new battery in and proceded to reprogram it according to directions, it still will not work. is it that we just need a new remote or...

If your vehicle accepted the programming codes, then it tells me that your vehicle sensing is working and that your remote worked at least during that period.

Whenever, you change batteries in a remote you should clean the battery and remote contacts with a pencil eraser to get rid of an corrosion.

Sep 22, 2011 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Remote does not work on my 2007 GMC Yukon. I changed battery and I used spare remote, but no response. After I drive the vehicle, the remote will work, but after I few minutes, it goes back to not working.

{: ) Try to reprogram your remote transmitter again. If you have two or more remote transmitters, they should be programmed at the same time (in one session only). Otherwise you may need to replace and reprogram your remote control receiver.

Apr 27, 2011 | 2007 GMC Yukon Denali

1 Answer

How do I program my car to have remote start? My 2007 Grand Prix came from the factory without this option but I would like to have this option. I have purchased a remote start fob, now I need help...

Sorry , but you need to take it to a GM dealer ! They need to go into the computer an turn that option on with factroy scan tool . Had to do samething to get speed control to work on 2006 chevy cobalt . BCM - body control module function .

Oct 28, 2017 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

I changed the car battery on my 07 chevy tahoe and both remotes are not working any more? do I have to go to the dealer in order to program them.

No. turn the key to the on position (not run). In your driver Information Center you should have an option to program your keyless entry. Access this option through your steering wheel controls. There are two buttons. One is a page button and the other is a select button. It will guide you to the reprogramming just make sure you do both remotes at the same time unless you only have one remote. When you are prompted to begin programming hold the lock and unlock buttons at the same time on the first remote and wait for it to program. Then do the second remote the same way. When you are done turn the key off then start the engine and confirm they work.

May 29, 2010 | 2007 Chevrolet Tahoe

1 Answer

How to recode remote door opener on 2007 chevy

The only way to program a transmitter is with a scan tool.If you have more than one transmitter then you have to program them both or if you program one the other one will not work.They do this at the dealership but if you are just replacing the batteries then you should not have to program the remotes.Hope this helps.Good luck.

Feb 23, 2010 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Key fobs not working i have changed the battries on both

: If a double audible warning sounds during the programming procedure a system malfunction has occurred. Repeat programming procedure.
Obtain all keys fitted with remote control. Open driver's door. Operate headlamp high/low beam switch to flash high beam position and hold. Insert key into ignition switch, turn to ACC position. Ensure system LED flashes once and an audible warning sounds. Operate headlamp high/low beam switch to flash high beam position 5 times. Ensure system LED flashes once and an audible warning sounds. Programming mode activated: Press and release lock or unlock button on first key. Ensure system LED flashes once and an audible warning sounds to indicate correct programming. Repeat programming procedure for remaining keys. Switch ignition OFF and remove key. Close driver's door. Check operation of keys. Keys can also be programmed using diagnostic equipment

Jan 31, 2010 | 2002 Jaguar X-Type

2 Answers

Keyless entry for my 07 Chevy Impala works on and Off

my 2006 impala keyless remote dont work i change the battery still the same problem the spare remote same problem how to solve this problem

Jul 21, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

Not finding what you are looking for?
2005 Chevrolet Suburban Logo

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides