Question about 1989 GMC S-15 Jimmy

1 Answer

89 S15 4.3L Need instructions to remove and install pwr steering

Power steering pump bracket, bolt on engine side of pump, bolted such that I cannot get a tool on the bolt head to remove bracket and pump

Posted by on

  • 2 more comments 
  • etman7 Feb 28, 2009

    denny

    The pump is located on the front of the engine just below the alternator. The pully is on the outside of the bracket, the pump is encased front and back and one bolt is located between the pump and the brackets rear plate. The bracket and the pump prevent tool insertion. I hope that I do not need to pull the pully.



    Thank You for your reply, I would appreciate any further advice.



    Larrycarroll

  • Anonymous Mar 22, 2014

    need power steering bracket

  • Anonymous Mar 28, 2014

    where does the bracket go for installation of the power steering pump?

  • Anonymous Mar 28, 2014

    installation whereabouts for bracket

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

I know what bolt your talking about,you canreach it thru the wheel well with an extention!!!
but if your just removing the pump,some of the pullys have three holes in them too get too the pump bolts if not then you need a power steering pump pully remover auto zone loans them out!!!!

Posted on Feb 28, 2009

  • Dennis Mulford
    Dennis Mulford Feb 28, 2009

    yes you must remove the pully !!! sorry about the first answer ithought you were talking about another bolt

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

How to remove power steering pump on a 2007 subaru b9 tribeca


before start job suction out power steering fluid out of pump using large sirenge or siphon pump then.you need a table vise and two pieces of wood.okay to remove power steering pump. you need to disconnect the ground cable.remove air intake duct.remove the pulley cover.remove the drive belt.disconnect power steering pump switch connector.disconnect the pressure hose and the suction hose from the power steering pump.cover power steering hose and pipe keep getting trash dirt and debris.remove the installation bolt of the power steering pump bracket.place the oil pump bracket in a vise btween two pieces of wood keep from damaging bracket and remove the two bolts from the front side of the pump.remove bolt from rear side of the oil pump.disassemble the oil pump and the bracket by inserting flat tip screw driver.to install tighten oil pump to bracket bolts 12 ft lbs. tighten the bolt from the rear side of the oil pump to 27 ft lbs.tighten steering hose eye bolts to 30 ft lbs.replace fluid bleed air out power steering system.

Nov 28, 2012 | 2007 Subaru B9 Tribeca

1 Answer

I want to know how to remove the alternator kia optima 2003


  1. Disconnect the negative battery cable.
  2. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  3. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  4. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  5. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  6. Remove the power steering pump, 2.0L engine only.
  7. Remove the power steering pump bracket, 2.0L engine only.
  8. Remove the alternator B terminal cover cap.
  9. Disconnect the alternator electrical connections.
  10. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  11. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  12. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  13. Remove the power steering pump, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  15. Remove the alternator tensioner mounting bolt and the belt tensioner.
  16. Remove the alternator pivot bolt.
  17. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  18. Remove the alternator.

    0996b43f80207fa4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0996b43f80207fa5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0996b43f80231908.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Alternator mounting-2.4L and 2.7L engine


To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Feb 09, 2011 | 2003 Kia Optima

1 Answer

NEED HELP WITH TORQUE SPECS ON 1998 CHEVROLET SURBURBAN CYLINDER HEADS 5.7


Cylinder Head Removal & Installation 5.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Drain the engine coolant.
  3. Remove the air cleaner assembly.
  4. Remove the upper radiator hose.
  5. Remove both heater hoses.
  6. Disconnect spark plug wires at distributor cap.
  7. Remove distributor cap.
  8. Remove the coolant bypass hose from the water pump.
  9. Remove the drive belt. NOTE: It is not necessary to evacuate the A/C refrigerant.
  10. Remove the A/C compressor from the mounting bracket and set it aside.
  11. Remove the wiring bracket from the rear of the cylinder head.
  12. Disconnect the accessory bracket and slide forward.
  13. Remove the upper and lower intake manifold.
  14. Remove the exhaust manifolds.
  15. Remove the valve rocker arms and pushrods.
  16. Remove the power steering pump pulley.
  17. Disconnect the electrical connector from the power steering pump.
  18. Remove nuts attaching the power steering pump to the engine.
  19. Remove power steering pump mounting bracket bolts and nut.
  20. Slide power steering pump/bracket assembly forward and remove stud.
  21. Set power steering pump/bracket assembly aside.
  22. Disconnect the wiring bracket from rear of the right cylinder head.
  23. Remove the generator.
  24. Remove the oil indicator tube bracket bolt.
  25. Remove the generator mounting bracket.
  26. Remove the sixteen cylinder head bolts.
  27. Remove cylinder heads and gaskets.
  28. Clean all sealing surfaces.
To Install:
Right Side NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the generator mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the generator mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the generator.
  16. Install the oil indicator tube bracket bolt.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.
Left Side To Install:
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
NOTE: Clean all dirt, debris, and coolant from the engine block cylinder head bolt holes. Failure to remove all foreign material may result in damaged threads, improperly tightened fasteners or damage to components.
NOTE: Do not use any type of sealant on the cylinder head gasket (unless specified).
  1. Clean the cylinder head bolt holes with a thread chaser and compressed air.
  2. Check the cylinder head locating pins for proper installation.
  3. Place a new cylinder head gasket over the engine block dowel pins.
  4. Install the cylinder head to the engine block.
  5. Apply sealant (GM P/N 12346004 or equivalent) to cylinder head bolt threads.
  6. Install the cylinder head bolts. gm-03-50-685.gif

  7. Tighten the cylinder head bolts in sequence on the first pass.
    • Torque to: 22 ft. lbs. (30 Nm)
  8. Using a torque angle meter, tighten the long bolts (1, 2, 5, 6, 9, 10 and 13) on the second pass in sequence to 75°.
  9. Using a torque angle meter, tighten the medium bolts (14 and 17) on the second pass in sequence to 65°.
  10. Using a torque angle meter, tighten the short bolts (3, 4, 7, 8, 11, 12, 15 and 16) on the second pass in sequence to 55°.
  11. Install the valve rocker arms and pushrods.
  12. Install the power steering pump mounting bracket stud.
    • Torque to: 15 ft. lbs. (20 Nm)
  13. Loosely assemble the mounting bracket over the stud.
  14. Install all nuts and bolts finger tight.
    • Torque to: 30 ft. lbs. (41 Nm)
  15. Install the power steering pump pulley.
  16. Connect the electrical connector to the power steering pump.
  17. Install the exhaust manifold.
  18. Install the lower intake manifold.
  19. Install the valve rocker arm covers.
  20. Install the wiring bracket to the rear of the cylinder head.
  21. Connect the accessory bracket.
  22. Install the A/C compressor.
  23. Install the drive belt.
  24. Install the distributor cap.
  25. Connect the spark plug wires to the distributor cap.
  26. Install both heater hoses.
  27. Install the upper radiator hose.
  28. Install the air cleaner assembly.
  29. Refill the engine coolant.
  30. Connect the negative battery cable.

Aug 31, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

What r the torque specifications on installing a head on a 1999 yukon and the tightening sequence


Check this procedure...
  1. Tighten the first design cylinder head bolts as follows:
    1. M11 bolts 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1,2,3,4,5,6,7,8): + 90 degrees.
    4. M11 bolts (9 and 10): + 50 degrees.
    5. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.
  2. Tighten the second design cylinder head bolts as follows:
    1. M11 bolts (1-10) 1st pass: in sequence to 22 ft. lbs. (30 Nm).
    2. M11 bolts (1-10) 2nd pass: in sequence + 90 degrees.
    3. M11 bolts (1-10): + 70 degrees.
    4. M8 cylinder head bolts (11,12,13,14,15) to 22 ft. lbs. (30 Nm). Begin with the center bolt (11) and alternating side-to-side, work outward tightening all of the bolts.

c409909.jpg

Fig. Cylinder head bolt tightening sequence-4.8L, 5.3L and 6.0L engines (click for zoom)


Install the cylinder head bolts in sequence to 22 ft. lbs. (30 Nm). The bolts must be tightened once, then be tightened again in sequence in the following order:
  1. Step 1: Short length bolt: (3, 4, 7, 8, 11, 12, 15, 16), plus 55 degrees.
  2. Step 2: Medium length bolt: (14, 17), plus 65 degrees.
  3. Step 3: Long length bolts: (1, 2, 5, 6, 9, 10, 13), plus 75 degrees.

7f05cb7.jpg

Fig. Cylinder head bolt tightening sequence-5.0L and 5.7L engines

Aug 04, 2010 | 1999 GMC Yukon Denali

1 Answer

Step by step to replace water pump on a 1995 chevrolet camro.


Water Pump - REMOVAL & INSTALLATION
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
3.4L ENGINE
(see Figures 1 and 2)
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the air intake duct.
  4. Remove the top coil of the ignition coil pack.
  5. Loosen the tensioner pulley bolt/screw.
  6. Disconnect the heater hose from the water pump.
  7. Loosen the water pump pulley bolts/screws.
  8. Unfasten the power steering bracket bolts/screws.
  9. Remove the serpentine drive belt.
  10. Remove the water pump pulley.
  11. Remove the power steering pump bracket and swing the bracket and pump aside. Do NOT disconnect the power steering lines from the pump.
  12. Unfasten the water pump and engine front cover bolts/screws, then remove the water pump assembly from the vehicle.
  13. Remove and discard the gasket and thoroughly clean the gasket mating surfaces.
9940b19.jpg

Fig. 1: Exploded view of the water pump mounting - 3.4L engine

To install:

  1. Position a new water pump gasket, then install the pump. Secure using all of the water pump retaining bolts/screws, except the bottom three, and tighten to 33 ft. lbs. (45 Nm).
  2. Install the engine front cover bolts/screws and tighten to 16 ft. lbs. (21 Nm) for 1993-94 vehicles, or to 97 inch lbs. (11 Nm) for 1995 vehicles.
371be42.jpg

Fig. 2: Water pump retaining bolt tightening sequence
  1. Install the three bottom water pump retaining screws and tighten to 89 inch lbs. (10 Nm).
  2. Place the power steering pump into position and install the pump bracket.
  3. Install the water pump pulley.
  4. Install the serpentine drive belt.
  5. Install the power steering pump bracket retaining bolts and tighten to 30 ft. lbs. (40 Nm).
  6. Connect the heater hose to the water pump.
  7. Install the top coil to the ignition coil pack.
  8. Attach the electrical connector to the alternator.
  9. Install the air inlet duct and air cleaner assembly.
  10. Connect the negative battery cable.
  11. Fill the cooling system. Start the engine and check for leaks.


3.8L Engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system into a suitable container.
  3. Remove the serpentine belt.
  4. Disconnect the radiator inlet hose from the water pump.
  5. Unfasten the water pump pulley bolts/screws and remove the pulley.
  6. Remove the water pump pulley retaining bolts, then remove the pump from the vehicle.
  7. Remove and discard the gasket and thoroughly clean the gasket mating surfaces

To install:
  1. Position a new water pump gasket, then install the pump. Secure using the water pump retaining bolts/screws and tighten to 11 ft. lbs. (15 Nm), plus an additional 80 degree rotation.
  2. Install the water pump pulley and retaining bolts. Tighten to 115 inch lbs. (13 Nm).
  3. Install the serpentine drive belt.
  4. Connect the radiator inlet hose to the water pump.
  5. Connect the negative battery cable.
  6. Fill the cooling system. Start the engine and check for leaks.

5.7L ENGINE
  1. Unplug the electrical connector from the cooling fan.
  2. For 1993-95 vehicles, remove the right side cooling fan.
  3. For 1996-98 vehicles, remove both cooling fan assemblies.
  4. Place a suitable drain pan under the vehicle, then remove the block coolant drain plug and the knock sensor. Drain the radiator.
  5. Install the drain plug and knock sensor.
  6. Remove the air intake duct and air cleaner.
  7. Disconnect the upper and lower radiator hoses from the water pump.
  8. Remove the heater hoses from the water pump and throttle body.
  9. Unplug the electrical connector from the coolant sensor.
  1. Unfasten the retainers and reposition the ignition coil and bracket.
  2. If equipped, remove the air pump and bracket.
  3. Unfasten the water pump attaching bolts, then remove the water pump and discard the gasket. Remove the shaft coupling and water pump driveshaft seals, if necessary.
  1. Thoroughly clean the gasket mating surfaces
To install:
  1. If removed, install the shaft coupling and water pump driveshaft using J 39089 or equivalent water pump driveshaft O-ring installer.
  2. Install the water pump with a new gasket. Tighten the bolts to 30-32 ft. lbs. (41-43 Nm).
  3. If equipped, install the air pump and bracket.
  4. Reposition and secure the ignition coil and bracket.
  5. Attach the coolant sensor connector.
  6. Connect the heater hoses to the water pump and throttle body.
  7. Connect the upper and lower radiator hoses to the water pump.
  8. Install the air cleaner and air inlet duct.
  9. Install the electric cooling fan(s), then attach the electrical connector.
  10. Refill the cooling system.
  11. Connect the negative battery cable, then start the engine and check for leaks.


Hope helps (remember rated this).

Jul 01, 2010 | 1995 Chevrolet Camaro

1 Answer

How do you get the power steering pump/alternator bracket off to remove the front driver side exhaust bolts on a 1995 k1500


there bolts holding the bracket on the engine frist u have to remove the alt make sure u discount battery frist then u have to unbolt pwr steering unit then ur bolts are free to remove

Mar 28, 2010 | 1995 Chevrolet K1500

1 Answer

How to check alternator, and how to replace it.



Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator.

    0900c15280028419.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-1.5L and 1.6L (VIN 5) engine shown


    0900c1528002841a.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.0L and 1.6L (VIN 3) engines shown


    0900c1528002841b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Alternator mounting-2.4L and 2.7L engine

To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).

  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).

  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).

  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).

  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.

Jul 29, 2009 | 2002 Kia Spectra

4 Answers

Torque specs for the cylinder head


2004 ENGINE
Engine Mechanical - 1.6L (L91) - Aveo
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fastener Tightening Specifications
Application
Specification
Metric English
A/C Compressor Mounting Bolts 27 N.m 20 lb ft
A/C Compressor Mounting Bracket Bolts 50 N.m 37 lb ft
Air Filter Housing Bolts 12 N.m 106 lb in
Alternator Adjusting Bolt 20 N.m 15 lb ft
Alternator Adjusting Bracket Retaining Bolt 20 N.m 15 lb ft
Auxiliary Catalytic Converter-to-Exhaust Manifold
Nuts and Bracket Bolts
40 N.m 30 lb ft
Camshaft Cap Bolts 16 N.m 12 lb ft
Camshaft Gear Bolt 67.5 N.m 49 lb ft
Camshaft Pressure Plate Bolts 10 N.m 89 lb in
Connecting Rod Bearing Cap Bolts 25 N.m+30°+15° 18 lb ft+30°+15°
Coolant Pump Retaining Bolts 10 N.m 89 lb in
Coolant Temperature Sensor 20 N.m 15 lb ft
Crankshaft Bearing Cap Bolts 50 N.m+45°+15° 37 lb ft+45°+15°
Crankshaft Position Sensor Retaining Bolt 10 N.m 89 lb in
Crankshaft Pulley Bolt 95 N.m+30°+15° 70 lb ft+30°+15°
Cylinder Head Bolts - Camshaft Support Housing
and Cylinder Head Mounting Bolts
25 N.m+60°+60°
+60°+15°
18 lb ft+60°+60°
+60°+10°
Electronic Ignition System Ignition Coil Mounting
Bolts
10 N.m 89 lb in
Electronic Ignition System Ignition Coil Mounting
Plate Bolts 10 N.m 89 lb in
Engine Mount Bracket Retaining Bolt 65 N.m 48 lb ft
Engine Mount Bracket-to-Engine Mount Retaining
Bolts
60 N.m 44 lb ft
Engine Mount Retaining Nuts 40 N.m 30 lb ft
Exhaust Flexible Pipe Bracket Bolts 40 N.m 30 lb ft
Exhaust Gas Recirculation Valve Adapter Bolts 25 N.m 18 lb ft
Exhaust Manifold Heat Shield Bolts 15 N.m 11 lb ft
Exhaust Manifold Nuts 25 N.m 18 lb ft
Flexible Plate Bolts 60 N.m 44 lb ft
Flexible Plate Inspection Cover Bolts 10 N.m 89 lb in
Flywheel Bolts 35 N.m+30°+15° 26 lb ft+30°+15°
Flywheel Inspection Cover Bolts 12 N.m 106 lb in
Front Muffler-to-Main Catalytic Converter Nuts 30 N.m 22 lb ft
Fuel Rail Retaining Bolts 25 N.m 18 lb ft
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 1 of 330
http://www.eautorepair.net/app/PrintItems.asp?S0=2097152&S1=0&SG=%7BEEDCF... 3/30/2009
ENGINE MECHANICAL SPECIFICATIONS
Engine Mechanical Specifications
Intake Manifold Retaining Nuts 25 N.m 18 lb ft
Intake Manifold Support Bracket Lower Bolt-to-
Engine Block 40 N.m 30 lb ft
Intake Manifold Support Bracket Upper Bolts 25 N.m 18 lb ft
Lower Timing Belt Cover Bolts 10 N.m 89 lb in
Oil Pan Retaining Bolts 10 N.m 89 lb in
Oil Pressure Switch 40 N.m 30 lb ft
Oil Pump Retaining Bolts 10 N.m 89 lb in
Oil Pump/Pickup Tube and Support Bracket Bolts 10 N.m 89 lb in
Oil Pump Safety Relief Valve Bolt 36 N.m 22 lb ft
Oil Pump Rear Cover Bolts 6 N.m 53 lb in
Power Steering Pump Mounting Bolts 25 N.m 18 lb ft
Power Steering Pump Pulley Bolts 25 N.m 18 lb ft
Rear Timing Belt Cover Bolts 10 N.m 89 lb in
Spark Plug Cover Bolts 3 N.m 27 lb in
Spark Plugs 25 N.m 18 lb ft
Thermostat Housing Mounting Bolts 20 N.m 15 lb ft
Throttle Cable Bracket Bolts 8 N.m 71 lb in
Timing Belt Automatic Tensioner Bolt 25 N.m 18 lb ft
Timing Belt Idler Pulley Bolt 40 N.m 30 lb in
Transaxle Bell Housing Bolts 75 N.m 55 lb ft
Transaxle Brace Bolts 40 N.m 30 lb ft
Transaxle Torque Converter Bolts 65 N.m 48 lb ft
Upper Timing Belt Cover Bolts 10 N.m 89 lb in
Valve Cover Bolts 10 N.m 89 lb in
Application
Specification
Metric English
General Data
 Engine Type 4 Cylinder - In-Line
 Displacement 1598 cm3 97.51 in3
 Bore Stroke 79.0x81.5 mm 3.1x3.21 in
 Compression Ratio 9.5:1
 Firing Order 1-3-4-2
 Maximum Power - At 6200 RPM 77 kw/103.3 hp
 Maximum Torque - At 3400 RPM 145 N.m 106.9 lb ft
Cylinder Bore
 Diameter 79 mm 3.1 in
 Out of Round - Maximum 0.0065 mm 0.00025 in
 Taper - Maximum 0.0065 mm 0.00025 in
Piston
MITCHELL 1 ARTICLE - 2004 ENGINE Engine Mechanical - 1.6L (L91) - Aveo Page 2 of 330

Jan 07, 2009 | 2004 Chevrolet Aveo

1 Answer

Changing the starter on a Kia Spectra


Here's step-by-step instructions on how to access, remove and re-install your alternator. Hope it helps! Have a great day!

Alternator Kia_Sephia_Rio_Spectra_Optima_1998-2006
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Temporarily loosen the water pump pulley bolts, 1.6L (VIN 3) engine only.
  4. Remove the front air intake inlet pipe bolts, 1.8L engine only.
  5. Remove the top hose from the air intake inlet pipe, 1.8L engine only.
  6. Remove the air intake inlet pipe clamp and the pipe, 1.8L engine only.
  7. Remove the power steering pump, 2.0L engine only.
  8. Remove the power steering pump bracket, 2.0L engine only.
  9. Remove the alternator B terminal cover cap.
  10. Disconnect the alternator electrical connections.
  11. Loosen, but do not remove the alternator pivot bolt and the tensioner mounting bolt.
  12. Remove the drive belt(s); relieve tension on the belt by rotating the adjustment bolt.
  13. Remove the water pump pulley, 1.6L (VIN 3) engine only.
  14. Remove the power steering pump, 1.6L (VIN 3) engine only.
  15. Remove the power steering pump bracket, 1.6L (VIN 3) engine only.
  16. Remove the alternator tensioner mounting bolt and the belt tensioner.
  17. Remove the alternator pivot bolt.
  18. Loosen the bolt at the base of the adjusting bracket and rotate the bracket up.
  19. Remove the alternator. 0900c15280028419.jpgAlternator mounting—1.5L and 1.6L (VIN 5) engine shown 0900c1528002841a.jpgAlternator mounting—2.0L and 1.6L (VIN 3) engines shown 0900c1528002841b.jpgAlternator mounting—2.4L and 2.7L engine
To install:
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Install the alternator.
  3. Install the alternator pivot bolt and hand-tighten at this time.
  4. Rotate the adjusting bracket into position, place the belt tensioner into position. Hand-tighten the mounting bolt.
  5. Install the drive belt.
  6. Adjust the belt tension by rotating the adjustment bolt.
  7. The belt deflection for 1.5L, 1.6L (VIN 5), 2.4L and 2.7L engines, is as follows:
    1. New belt: 0.22-0.28 in. (5.5-7mm).
    2. Used belt: 0.24-0.28 in. (6-7mm).
  8. The belt deflection for 1.6L (VIN 3) engine is as follows :
    1. New belt: 0.13-0.15 in. (3.3-3.7mm).
    2. Used belt: 0.17-0.19 in. (4.2-4.7mm).
  9. The belt deflection for the 2.0L engine, is as follows:
    1. New belt: 0.22-0.31 in. (5.5-8mm).
    2. Used belt: 0.33-0.45 in. (8.5-11.5mm).
  10. The belt deflection for the 1.8L engine, is as follows:
    1. New belt: 0.23-0.31 in. (6-8mm).
    2. Used belt: 0.28-0.35 in. (7-9mm).
  11. Tighten the tensioner bolt to 14-19 ft. lbs. (19-26 Nm) and the pivot bolt to 28-38 ft. lbs. (38-51 Nm).
  12. Connect the alternator electrical connections.
  13. Install the alternator B terminal cover cap.
  14. Install the power steering pump and adjust the power steering belt tension, 2.0L and 1.6L (VIN 3) engines only.
  15. Install the water pump pulley, 2006 1.6L engine only.
  16. Install the air intake inlet pipe and fasten the clamp, 1.8L engine only.
  17. Install the top hose to the air intake inlet pipe, 1.8L engine only.
  18. Install the front air intake inlet pipe bolts, 1.8L engine only.
  19. Connect the negative battery cable.
 

Nov 23, 2008 | 2003 Kia Spectra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...