Question about 1995 Lexus ES 300

1 Answer

No power stearing new rack 3 weeks ago

When i pulled into the gas station i could hardly turn the wheel new rack and allignment 3 weeks ago has power stearing fluid

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You probably need a new power steering pump

Posted on Feb 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mercedes gl 450 2007 stiff turning


Check the ball joints and the belt tension.

Nov 11, 2013 | Cars & Trucks

2 Answers

I had a new rack put on my 93 5.0 mustang. The steering wheel is turned to the right when driving straight, not pulling. Seems like a little play in steering wheel. How do you fix this? Thanks


Seems to me the steering wheel was not aligned to the central position when the new rack was installed. This may be a job that needs to be rectified by the installer. If the steering is sloppy thisoo may need to be looked at by the installer.

Nov 18, 2010 | Ford Mustang Cars & Trucks

1 Answer

Why would my right passenger front wheel vibrate and shake when hitting a bump?


first check the wheel bearing on that side if its not floppy check the ball joints for wear try lifting them any life in them shows there worn out,,,then check the shocker bounce the wing a fuw times and let it go if it keeps bouncing up and down more than a fuw times (2) the shocker is worn out,,,the last thing to test is the stearing arm from the stearing box/rack get hold of the wheel at 3 and 9 o clock push and pull on it,,if its easy to turn and floppy look for any bits in the stearing that flop about

Aug 24, 2010 | 2004 Mitsubishi Lancer

1 Answer

Lot of play in sterring wheel


the stearing wheel with a play usually means one thing.. the stearing box..

you can eighter change the seals and stuff in the box,, or change the box all together.. Also the stearing rack could be at fault as well.. same thing applies,, change seals of change rack.. Remove the rack firstmm its the most likey cause.

Mar 17, 2010 | 1994 Chevrolet C1500

1 Answer

Power stearing isnt working it is shreaded


If it is just the pump, not too awful. need to pull the right front wheel and remove some splash guards on the inner fender well.
Replacing the steering rack is alot more work.
Hope this helps.

Jun 02, 2009 | 1997 Plymouth Voyager

1 Answer

Power steering difficult to turn wheels in tight stationary spots


no its not.. something is wrong with the power stearing assemply. is there oil leaking ? if so there may be a hole i the line. of nothave the power stearing motor checked.

Apr 04, 2009 | 2000 Chevrolet Silverado 1500

1 Answer

Stearing pump nnoise 1995 toyota tacoma


you may have air in the lines to the steering rack. or the fluid is low. there is also a chance your replacement pump is defective. a lot of steering pumps are remanufactured. a way to check for air in the lines is to take the filler cap off, have someone turn the steering wheel lock to lock a few times and hold for a few seconds at full lock each time, check to see if any air bubbles arise in pump reservoir. if no bubbles are seen you can also try a vacuum pull on the reservoir if you have the tool to do so, that tool will pull any air from the lines, but the engine has to be off because it will also pull some fluid from the pump in the process, when you don't see any air bubbles in the vacuum tools's lines it should be ok.

Jan 03, 2009 | 1995 Toyota Tacoma

Not finding what you are looking for?
1995 Lexus ES 300 Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...