Question about 2000 GMC Jimmy

2 Answers

97 gm sierra, ABS screwing up. When coming to a stop, brakes are fine then pedal goes to floor and at last minute they come back. Doesn't happen all the time. sometimes you can hear ABS pump running when you're not on the brakes. Took out ABS fuse and brakes work great. Intermittent problem with constant nerve and hair loss!!!

Posted by on

  • baby_weasle Feb 27, 2009

    I already did and there is no codes stored

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

I have a 2000 gmc sierra . and the brakes did the same thing . and yes i took out fuse and brakes work better than ever . been looking around for a new one they are about $300 . forget used around my area cannot find any . did however find a place online that does rebuild them . just waiting for a reply back to see the cost

Posted on Oct 23, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Check system for trouble codes

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 corolla, brake pedal goes to the floor. how can we fix the brakes?


is the abs light on?the abs system only effects the pedal when you are stopping quickly to activate the system. you still have a hydrualic brake pressure problem. are the rear brakes shoes or pads? rear shoes out of adjustment can cause a low brake pedal.even though the master cylinder has been replaced doesn't mean you got a good part.if the part was a remanufactered part very likely it is bad. to determine if it is the master cylinder, plug off the lines from the side off the master cylinder and hit the brake pedal. if the pedal stays up look for a problem elsewhere in the system. if the pedal drops the the master cylinder is defective.

Jun 11, 2012 | Toyota Corolla Cars & Trucks

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Brake pedal


You will need to bleed the brake fluid again starting at the furthest wheel cylinder working your way up to the closest to the master cylinder. This way you will remove all air from the lines. Do the master cylinder last. The ABS must be done as well before the master cylinder

May 23, 2010 | 2002 Toyota Camry Solara

5 Answers

Brake pedal goes to the floor only when engine is running. Pedal is perfect with engine off.


your power brake booster is blown out
the seal has a leak in it
run the truck for 3 minutes and shut it off. with the windows up listen carefully while you gently apply the brakes
listen for a hissing sound of air leaking.
the sound of these leaking is a very soft sound

Mar 27, 2010 | 1998 Chevrolet K1500

1 Answer

1997 GMC Sierra 5.7 changed master cylinder calipers and brake pads. I have a hard pedal until I turn the truck on and the pedal goes to the floor? Is there something I am missing? I have bled the brakes...


check under your master cylinder,is there another clyinder below with one line in and one line out,if you do I found this is for the Abs to the rear,I had to replace this it was full of air,and did exactly what yours is now

Dec 06, 2009 | 2003 GMC Sierra 1500

1 Answer

Clattering out of left front on braking


pedal goes to floor .... did you change the calipers.... sounds like air in the system

Jun 18, 2009 | 2001 Ford Explorer Sport

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

3 Answers

97 sierra ABS problem


ABS comes on all by it self at low speed braking, A GM defect with their brakes!!!! Sensor thinks the tires are locking up an puts on the ABS, my advice pull the ABS fuse the brakes work better!!!!! Sensor is **** never had a problem with my Honda's ABS I sent a letter to GM 0 response, never will buy one again!!!

Feb 28, 2009 | 1998 GMC Sierra

3 Answers

1998 GMC 1500 4x4 4.3L ABS brake problems


Or you could just pull the fuse for the abs and not have abs but you won't wreck from pulsating pedal.

Jan 01, 2009 | 1998 GMC Sierra

2 Answers

97 ford e350 brake pedal goes to the floor...


are your rear drums set up? why did you bleed the brakes. when only when you installed new pads?

Sep 11, 2008 | 2002 Ford E350

Not finding what you are looking for?
2000 GMC Jimmy Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...