Question about 1993 Saturn SL2

1 Answer

Problem with all door lock/unlock and dome light.

The problem Is;
Yesterday I was trying to set a new keyless remote control with my Saturn SL2 1996. I used a paper clip to do It. First I jumped the 4th pin and then, when I was going to jump the  8th pin, the paper clip touched the 16th pin causing a short circuit. Then the dome light went out and none of the 4 doors are locking or unlocking. I did  check the door lock/unlock fuse and apparently It Is ok (there is 2). Please, tell me what to do to fix it!! Thanks  a lot In advance. While attempting to program a replacement remote for my 1996 Saturn SL2 by using a U shaped paper clip I accidentally shorted the wrong terminals and lost power door locking capability and dome light. Underhood fuse appears to be all right. Relay modules on the instrument panel junction box show no burned terminals but I have no way to test them. Replacement poses to be difficult as there is no part number.on these 5 connector relays of OMRON manufacture.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,800 Answers

Check ur model and statt from here

http://www.autzone.com/shopping/repairGuide.htm

plz rate

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

I have a 1995 F350 crew cab with keyless entry and the dome lights controlled by...


There are two jam switches located on the latch assymbly. One on top and one at the bottom. They can become dirty and not function properly causing the dome light to stay on until it "times" out. They can be removed and cleaned so they don't stick. Once I found them, it took me about an hour to completely remove the door panel, latch assymbly, and to reinstall everything back.

on Jul 22, 2009 | 1996 Ford Ranger SuperCab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Keyless entry not working


Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. Remove key from ignition switch. Close all doors. Open driver's door. Carry out the following within 24 seconds: Turn ignition switch ON and back to LOCK position 3 times. Remove key. Press and release driver's door courtesy light switch 3 times. Ensure doors lock and unlock. If not, wait 40 seconds and repeat procedure starting with driver's door already open. Press each remote control lock or unlock button twice. Ensure doors lock and unlock after each remote control operation. If not, proceed as follows: Press and release driver's door courtesy light switch once. Ensure doors lock and unlock twice. Repeat procedure starting with driver's door already open.
NOTE: A maximum of 3 remote controls can be programmed.

Mar 29, 2010 | 2004 Mazda 6

1 Answer

Alarm sets itself with doors unlocked


An auto Electrition will bypass the alarm for you.As a temporary mesure remove the battery earth lead and leave off for 6 hours..

May 28, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Keyless entry blinks dome light and does nothing else


The remote is fine - your problem is the lock actuators in the doors. They're a bit of a pain to replace - so, you may want to have a professional do it.

May 03, 2009 | Dodge Dakota Cars & Trucks

1 Answer

Problem with all door lock/unlock and dome light.


open the fuse box on the passenger side of the console. Check all the fuses. Also there is a fuse box under the hood I believe on the driver side. check all these fuses also. The only other thing to check if your motors are working fine, is the wiring.

Oct 18, 2008 | 1993 Saturn SL2

1 Answer

My car is acting crazy!


" turn the key on engine off 8 times. the doors will lock and unlock. push one of the buttons on the key fob and the doors will lock and unlock. do this for each remote that you have. when you are done turn the key off. the door locks will lock and unlock. the remote fob should work after this."
From My SecuriLock..

Sep 05, 2008 | 2006 Ford Taurus

Not finding what you are looking for?
1993 Saturn SL2 Logo

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...