Question about 2000 Dodge Dakota Quad Cab

1 Answer

Burned out front turn signal bulb in 2000 dodge dakota

I can get my hand up inside the cavity to remove the bulb, but after I turn the bulb assy to loosen it, it won't come out because it hits the wall behind it. How do you get it out. I figure you have to remove the lens from the front but I can't see how.

Any help will be appreciated.

Phil Glaze

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

THERE IS A TORQUE SCREW JUST BELOW WHERE THE CLEAR LENSES CONNECT. JUST CHANGED MY DRIVERS TURN BULB PULLED OUT FAR ENOUGH SO THAT I DIDN'T HAVE TO REMOVE THE SCREW

Posted on Mar 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change headlight assy on 2000 dodge caravan


Remove the screw from the black tab on top of the headlamp assembly. Around the headlamp plug, there are 3 nuts, remove them carefully, as they are easily dropped and lost, remove the ring that secures the bulb to the assembly, it only turns a portion of a turn. Slide the entire headlight assembly partially out the front, then disconnect the rubber plug that contains the marker/turn signal bulbs. Re assemble in reverse order, making sure the headlight bulb is properly aligned or the ring will not tighten. Also,take care not to touch the headlight bulb glass, as the oil from your fingers may cause the bulb to break when it heats up. Hope this helps.

Feb 26, 2015 | 2000 Dodge Caravan

1 Answer

Blinker come on but don't flash bulbs and flasher are ok


this usually means you have a turn signal bulb that is burned out. The blinker measures the power to the bulbs and that controls the flash rate. If a bulb is burned out it does not flash.

Also if you changed your bulbs to LED the current draw is less and could cause the same situation

Aug 24, 2013 | 1991 Dodge Dakota

1 Answer

Left turn signal blinks faster than right turn signal blinks


The blinker is made to warn you that one of the bulbs is not working. When it blinks faster than normal one or more bulbs are burned out.

Sep 10, 2010 | 2001 Dodge Dakota

1 Answer

The passenger side signal lights light but will not flash on the front and the rear one flashes fast


You need to replace the bulb in the front right signal light socket.Remove the lense assembly then twist the socket to the right and it will be in your hands.Pull the tabs on the bulb together and pull out the bulb,reverse everything to install.

Nov 21, 2009 | 2001 Dodge Dakota

1 Answer

How do you change a burned out front right side turn signal bulb?


YOU HAVE TO REMOVE RIGHT SIGNAL BULB FROM INSIDE THE FENDER NEXT TO FRONT WHEEL.

Sep 28, 2009 | 2000 Chevrolet Corvette

1 Answer

How to remove and replace right front turn signal bulb?


SEE IF YOU CAN PULL IT JUST A LITTLE BIT FROM THE CLAMPS (CAREFULL). IF NOT REMOVE THE TORQUE SCREW JUST BELOW WHERE THE CLEAR LENSES CONNECT.

I JUST REPLACED MY DRIVERS SIDE WITHOUT REMOVING THE SCREW.

Mar 22, 2009 | 2000 Dodge Dakota Quad Cab

1 Answer

Should be simple pass. side headlight bulb replacement.


JUST REMOVE THE AIR BOX INTAKE TUBE . THE BULB REMOVES FROM THE BACK OF THE LIGHT ASSY. .

Mar 14, 2009 | 2001 Dodge Dakota

1 Answer

1992 Dodge Dakota LH tailight problem


Have you taken bulb out & cleaned terminals inside socket & either cleaned bulb base & terminals, or tried replacing bulb?

Mar 10, 2009 | 1992 Dodge Dakota

1 Answer

2000 dodge caravan rear passenger blinker not working


CHANGE THE SOCKET FOR THE BULB THATS FAILED ALSO CHECK THE TAIL LAMP ASSY, THE CONECTOR ON THE LAMP MAY BE DISTORTED AND NO CONTACT TO THE SOCKET.

Dec 30, 2008 | 2000 Dodge Caravan

1 Answer

I can't figure out how to replace the front turn signal


There is one screw on top of headlight assembly that holds turn signal lens in place you have to remove that screw and pull lens straight out. As far as head lamps go its just a matter of getting your hand behind headlight assembly to remove the collar that holds the bulbs in place.

Nov 11, 2008 | 2000 Honda Accord

Not finding what you are looking for?
2000 Dodge Dakota Quad Cab Logo

241 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...