Question about 2000 Toyota Avalon

Open Question

How to change front directional light bulbs in a 2001 toyota aval

Need access to kight socket for directional front light bulbs

Posted by on

6 Suggested Answers

  • 1 Answer

SOURCE: How do I replace the Rear Brake light bulb of 2001 Toyota Sienna?

I have a 2001 Sienna and have had to replace most of my tail light bulbs.

The bulbs that are mounted in the fender (wrap arounds) have acess panels in the van's interior that easily pop out and expose the back of the light assembly.

However, the bulbs that are found in the lift gate are a different matter. You have to remove the whole interior panel to the lift gate to expose the light assemblies. Go to your auto parts store and get a tool to help pop out the plastic retainers from the lift gates metal frame. Don't force the retainers out. Go slowly and gently so that you don't damage the interior panel. If you are really gentle you might even get to reuse the retainers.

Good luck!

Posted on Jul 01, 2009

  • 7353 Answers

SOURCE: toyota spacio changing headlight. Access bulb from behind or

behind

Posted on Sep 21, 2009

jlisagearhea
  • 412 Answers

SOURCE: how to change light bulbs both front headlights

nothing at all...simply remove your light bulbs by spinning them counterclockwise and then reinstall new

Posted on Nov 14, 2009

  • 215 Answers

SOURCE: How do I change the headlight bulb?

rubber gasket can be peeled back to expose conector.

Posted on Feb 21, 2010

Testimonial: "Thanks so much. The advice worked perfectly. "

Bray2thaden
  • 173 Answers

SOURCE: how to change head light bulb toyota corolla 98.

no!!!! its difficult, but possible... the headlights have a rubber cover over the wiring harness. pull it off, un plug the harness, and there is a metal wire bracket, hard to explain, if you check out the driver side first (easier to access) the other side should be a breeze. hope this helps

Posted on Mar 08, 2010

Ironfist109
  • 3018 Answers

SOURCE: How to Change a 2001

  • It's a tight fit for that third one. It takes some force but it just turns like the others, this one is just a bit harder. No secret just give it a stiff turn to the left.


Regards, Tony

Posted on May 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the license plate lights on 2004 Toyota Camry


You must remove as many of the retainers holding in the liner for the trunk lid to get at the bulb assembly. You must take the bulb socket and twist 1/4 turn counter clockwise to release it. You then gently pull the bulb directly out of the socket. reverse for installation.

Mar 16, 2012 | 2004 Toyota Camry

1 Answer

How do you change the front turn signal bulbs on a 2001 Mercury Grand Marquis LS?


open hood you will see a long black panel across the front. this panel is called a sight shield you will see 3 "twist clips" one on ether side of each head light and one right by the hood latch . twist all 3 and remove panel.at this point you will see the light sockets.each headlight assembly has 2 retainers. simply unlatch the retainers and the lamp assemblies come out easily and you have access to the bulbs.

Dec 15, 2009 | 2001 Mercury Grand Marquis

1 Answer

How to change light bulbs both front headlights and tail lights, what needs to be removed to allow access to the light bulbs, 1991 toyota tercel


nothing at all...simply remove your light bulbs by spinning them counterclockwise and then reinstall new

Nov 14, 2009 | 1991 Toyota Tercel

1 Answer

The light in the back of my toyota echo has gone out i have tried replacing the bulb and it has not justified the problem, can u lead me into the right direction?


frist thing is to check for power at the wires at that bulb socket,may have bad socket or bad wire, start there.

Oct 08, 2009 | 2001 Toyota Echo

1 Answer

How do I change the front turn signal bulb in my 2001 WS6 Trans am? How do I get to it?


Remove two bolts that secure the plastic panel on the underside of the front end of the car, directly below the turn signal housing. The panel will then hinge down allowing you to reach up and access the bulb socket, which has a lock ring that must be compressed while you turn the socket to remove it from the housing. If yours is like mine, the wires are too short to drop below the access panel, so you'll have to reach up with both hands to change the bulb. Also, if yours is like mine, you may see evidence that the bulb gets so hot that the socket shows evidence of burning and/or heat degradation. I'm actually on this site looking for information on a possible recall by Pontiac for this, or at least maybe an upgrade socket.

Jun 03, 2009 | 2001 Pontiac Firebird

3 Answers

Left turn signal blinks fast in rear and regular in front


Very simple the bulb is out. When the blinker does that its telling you the bulb needs to be replaced

May 17, 2009 | 2001 Chevrolet Corvette

1 Answer

Signal light bulb change/who and where


  1. From under front wheelhouse, remove access cover behind park and turn signal lamp
  2. Through access hole in wheelhouse, rotate park and turn signal socket counterclockwise one quarter turn.
    1. Pull socket from back of lamp.
    2. Pull bulb from socket. INSTALLATION
      1. Align key on bulb base to groove in socket and insert bulb into socket.
      2. Through access hole in wheelhouse, insert socket into back of lamp.
      3. Rotate park and turn signal socket clockwise one quarter turn.
      4. Install access cover and verify lamp operation.
Hope this helps with your prob

Mar 27, 2009 | 1998 Plymouth Voyager

2 Answers

Replace turn signal bulbs on 2001 corvette


Rears are simply remove the two screws on the lens and remove the tail light from the Vette, twist the connector to get to the bulb. Reverse instructions to install. For the fronts jack up the front, remove the small closeout panel under each side, push the brake cooling duct to one side and twist the bulb socket out of the light to get to the bulb. Reverse instructions to install.
sebring1962@yahoo.com

Feb 22, 2009 | 2001 Chevrolet Corvette

1 Answer

Break kight burned out


Open the liftgat and you should see the screws on the side of the lamp. Unscrew then and pull the lamp away from the vehicle. There should be sockets in the tailamp that screw in and out about the size on a half dollar. Pull this out and pull the bulb out straight and replace by pushing in a new bulb. Follow these directions backwards to replace the lamp. Hope this helps.

Jan 12, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
2000 Toyota Avalon Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...