Question about 1986 Ford Ranger 2WD

1 Answer

2001 Ford Ranger right turn signal doesn't work when the braking

When I have the right turn signal on and apply the brakes the turn signal lights stop flashing and stay on until I take my foot off the brake...then they flash again...
All of my bulbs are working.
The left turn signal works properly...

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 319 Answers

Flasher Unit sounds bad... change the flasher, which is in the inboard fuse panel.

Posted on Feb 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Wen i press break pedal the flasher stop blinking On my ford ranger 2009


check the brake lamp/turn signal bulbs. sometimes in a dual filament bulb the filament will break and lay over on to the other, so when the turn signal is on and the brakes are applied, it just powers the circuit by-passing the flasher

Jan 13, 2017 | Ford Ranger Cars & Trucks

1 Answer

2005 Suburban brake signal light issue


Sounds like a faulty turn signal switch. The brake light wire is routed through the turn switch, so it appears the turn switch has gone crazy.

Dec 27, 2013 | 2005 Chevrolet Suburban 1500

1 Answer

97 Oldsmobile bravada my right brake light won't


Sounds like a short in the socket or a bad ground.
The parking light is one circuit and the brake turn signal is another.

Jul 24, 2013 | Cars & Trucks

1 Answer

Brake Light will not work? Cab brake light does.


The high mount stop light and the regular brake lights are actually on different circuits. The regular stop lights go through the turn signal switch which is known to go bad on older ford vehicles. Something to check into. Also be sure to check all the fuses.

Jan 10, 2010 | 1999 Ford Ranger SuperCab

1 Answer

Emergency flashers remain constant ON when the brakes are applied


It is as intended. If you check with everyone else, their car does exactly the same thing!!

Oct 09, 2009 | 1987 Ford Ranger

1 Answer

2006 Ford Ranger. Rear passenger side tail light


Bad earth connection.Clean or replce wire.

Jun 18, 2009 | 2004 Ford Ranger

1 Answer

I have a '05 Ford Ranger. I bought a camper shell that has a Third Brake Light and I would like to hook it up so it works when I apply the brakes. Hooking the camper shell 3rd Brake lights to the p/u brake...


there will be four wires going to your lights you will have to test each wire to see which wire is for the brake light and tap into that wire. on all ford rangers one bulb controls everything so you can't just hook it up thru your bulb so you will have to hookit up thru your wires. it's not that difficult but you will have to have a helping hand. and test till you find the one for the brakes only.

Jun 09, 2009 | 2005 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

463 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...