Question about 1988 Chevrolet Blazer

1 Answer

I have a 94 GMC 1500 pick up. I replaced the

I have a 94 GMC 1500 pick up. I replaced the igniton switch down on the column. When I went to connect the linkage back on it, it does not line up and when I lock the key it tries to start and when I try to start it turns everything off.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,055 Answers

The thing too do is take out the 4 bolts holding the colum drop it down so you can see what your doing,take the swtich out,turn the key too the off poistion,now find the hole in the switchstick a small philips screwdriver in it pull it back all the way too the end (that will be thee acc setting)then move it one click foward ,then put the switch on the rod and bolt it up,then see if it will statr, if it does put it all back togethe your in adjusment!!!!

Posted on Feb 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove key switch from 94 gmc Sierra 1500


It might have a small lever just behind the key that you push down and then can rotate the key a bit before taking out

Jun 12, 2015 | GMC Sierra 1500 Cars & Trucks

1 Answer

I need an Illustrated Parts Break down for a 1989 GMC Sierra 1500. 350 w/ PS/PB loaded. Steering column Removal Repair or Replace


Hi.

Below you get all the parts breakdown for GMC Sierra 1500, including steering column assembly:

1500 SIERRA

Here diagrams for all 1989 GMC trucks.

If you need to take apart the steering column you will also need wiring. below the color codes and wiring tips:

GMC SIERRA 1988-2005 VEHICLE WIRING

Regards.

Ginko

Aug 31, 2011 | GMC C1500 Cars & Trucks

1 Answer

Location of ac low pressure switch 2003 gmc 1500 and how to change it. thanks mike


What makes you think it needs replacement? It lives in a very clean environment and rarely fails. Low refrigerant, on the other hand, would be picked up by the low pressure switch, and it would shut down the system to prevent EXPENSIVE damage... Great design, I think.

Replacement of the low pressure switch would require recovery of refrigerant, evacualtion of the system, and recharge, at minimum.

this job is best left to a qualified shop, as you risk serious personal injury.

May 22, 2010 | 2003 GMC Sierra 1500

1 Answer

I have 1994 gmc 1500 5.7 brake lights want work replaced brake switch also brake relay control still not working help


next is to check the wiring at the signal light switch,check were the connecter from the switch plugs into the main harness this is located at the lower part of the steering column, its common for the brake light hot wire to heat up there causing a bad connection, ive repaired a few of these, also heres a wiring diagram to help you, hope this is helpful.13bfafc.gif

Feb 13, 2010 | 1994 GMC Sierra

1 Answer

Can you put a steering column from a 1997 c/k 1500 chevy truck in a 1994 c/k 1500 chevy truck? I am putting the motor (4.3 V6) from a 1997 c/k 1500 chevy truck into a 1994 c/k 1500 chevy truck. I need...


pick up a chilton book from chapters indago and check the diagrams they might be similar but i believe the wiring is a lot different '
it is likely you will need both manules

Jan 08, 2010 | Chevrolet Chevy Cars & Trucks

1 Answer

96 gmc yukon headlights will not turn on


Before the lights went out did you have trouble with your high and low beams not always doing what you wanted?If so you'll have to replace your dimmer switch in the column.The wires, over time will fray and break.

Jun 29, 2009 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

90 gmc sierra no start


Try another coil and mount it correctly. Check wires for power.

Apr 15, 2009 | 1990 GMC Sierra

1 Answer

Ignition switch does not shut off motor


The connection between the Lock cylinder and the Ignition switch has come apart. There is pin that holds it together where the column tilts to allow for the tilt. The bad thing is the column needs to be completely disassembled to fix it, or replace the column with one from a salvage yard. The pin that falls out is usually still inside the column if you take it apart.

Feb 27, 2009 | 1996 Ford Windstar

1 Answer

Igniton switch installation


Remove column cover, remove wiring harness, cut a slot in 2 bolts (originally breaw away bolts) holding swith assembly to steering column ??? remove put in new one

Dec 24, 2008 | 1988 Mazda B2200

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...