Question about 1996 Acura Integra GS-R

1 Answer

I push the clutch and cant get it into gear sometimes i can sometimes i have to put in first gear and start it with the clutch in the car will start to go

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 463 Answers

Usually there is a rod or cable that adjusts the 'throw' of the clutch. Sounds like this is out of adjustment. I think you need a couple of 13mm wrenches to adjust this in your car.

Posted on Feb 27, 2009

5 Suggested Answers

rockitman187
  • 2559 Answers

SOURCE: I have got the flywheel resurfaced put it on

does the clutch pedal have pressure as soon as you push it or is it going beyond halfway down before you feel the pressure?

Posted on Jul 21, 2009

j_del
  • 1586 Answers

SOURCE: 1993 nissan 240sx clutch problems

Did you bleed the system fully after changing the cylinders? Those are the two main components that cause such problems. If you bled the system out, and it still has the problem, then you most likely have a ruptured line somewhere that is allowing air into the system.

Posted on Aug 24, 2008

  • 111 Answers

SOURCE: when i push the clutch in it won't go into gear

Check the master cylinder resevoir and make sure you have sufficient fluid. Hopefully it isn't your tranny.

Posted on May 23, 2009

  • 365 Answers

SOURCE: clutch wont engage or disengage

You may need to have the cable adjusted to allow the pressure plate to disengage from the clutch plate

Posted on Jul 13, 2009

SOURCE: cant put car in gear..clutch peddle stays

your transmission gear sir maybe could have mechanical problem.

Posted on Dec 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just put a new slave cylinder and clutch master cylinder on a 2003 Honda accord 3.0 V6 six speed and you can shift the gears without the clutch pedal pushed in or the car started


that is normal if the gear synchro dogs ( teeth) are in line in the box
problems concerning a clutch are
slashing gears when trying to engage first or reverse with the pedal to the floor ---needs bleeding
slipping when the clutch pedal is released--- slipping clutch from the pressure not being released ---problem in master cylinder
reverse gear is the only gear not synchronised so even with the clutch depressed it is possible sometimes that it will not go into gear unless you let the clutch up to move the gears in the box then attempt to re-engage reverse

May 04, 2016 | Honda Cars & Trucks

1 Answer

I have a 2001 mitsubishi challenger manual which is sticky to put in and out of gears sometimes not letting me access a gear I have to find one then easy again


Try putting pressure on the gear shift while letting out the clutch. When you feel the gear shift move a little push the clutch back in.

Apr 19, 2016 | Mitsubishi Cars & Trucks

1 Answer

1998 Honda Civic manual trans will not shift into gears. Car starts, push in clutch and it goes to the floor, release clutch and comes back up. Unable to put into gears. Brake fluid and clutch fluid seem...


Eric, how are you confirming whether or not the car goes into gear if you shift gears without the engine running? One way would be to put it in 1st and see if you can push the car. If you can't, it is in gear.

Another option is to roll the car slightly forward or backward (engine off) while trying to put the car in gear. Once it is in gear, then the car shouldn't move any further. However, if it goes into gear, DO NOT start the car without taking it back out of gear.

The clutch is much more likely to be the problem than the transmission.

If the clutch fluid ever ran dry, then the clutch hydraulics will need to be bled of air. Otherwise, the problem could be the clutch master cylinder, slave cylinder or throwout bearing. Since you didn't report the clutch slipping (e.g. engine revving without accelerating when in gear) it is likely not the clutch disks themselves.

Jun 11, 2014 | Cars & Trucks

1 Answer

Suzuki won"t shift into gear unless I turn the car off and put it into first


make your adjustment to clutch, see how that works, but start saving up for a new clutch, or just have your inspection mechanic, take a look @ it for you, make the adjustment, and he can remove a cover and inspect the condition of your clutch with his own eyes. its a lot easyier for him than you. then, you'll know for sure. good luck

Jan 13, 2013 | 2001 Suzuki Grand Vitara

1 Answer

On my 1996 chevy silverado, i have problems shifting in to first gear, as i start pushing forward to clutch into first, the truck starts to move forward as if im pushing it when im trying to clutch in, and...


it hyd clutch the fliud could be to full take paper towol get some out then tray you might have to replace clutch mastercylinder tray bleed at slave cylinder could have air in system

Jan 30, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

2 Answers

2003 chevy s-10 want start sometimes


there is a clutch switch on the end of clutch peddle this is for safety reasons so you dont launch into lets say your house if it was in gear when you tried to start the truck without pushing in the clutch .i dont recommend bypassing the switch though there are two wires that go to it if put together that will bypass the switch.

Feb 26, 2009 | 1988 Chevrolet S-10

Not finding what you are looking for?
1996 Acura Integra GS-R Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...