Question about 1992 Dodge Ram 250

1 Answer

No spark power in&out of coil but no spark

Posted by on

  • mator123 Apr 04, 2009

    no spark coil and pickup coil ok

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Check for signal from distrubutor as it acts as your igniter open and close switch or get a haynes manual from auto parts store to trouble shoot it multi meter required for ohm test and voltage drop test and test light. you may have power and ground but no signal. your igniter or incorrect gaps. Its a 20$ book with pictures....

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark at plugs. Has power to coil


By power to coil do you mean spark comes out of coil tower or only the feed wire to the coil has power ? If only the feed wire has power the coil may be bad. Which engine do you have ?

Mar 31, 2016 | 1987 Honda Civic

1 Answer

James what can I do to check coils on ,2003 accord lx 2.4


Not James, but maybe I can help: Under the dash in the fuse/relay box is the ignition coil relay. This sends battery voltage on the black/white wire to all four coils. With key in on, all 4 coils should have power to them on this black/white wire. If no power, check fuse #2, a 15 amp fuse which sends power to the ignition coil relay, and on to the coils when the relay is energized by the ecu/pcm. Only thing else to cause spark is when the ecu/pcm sends a signal to the coil's Ignition Control Module (housed inside each coil assembly), which controls the primary circuit (the black/white wire), and causes high voltage to the spark plugs.

So check the black/white wire to the coils. If power there with key in on, check for spark at a spark plug when cranking the engine over. If power to coils but no spark, possibly a crankshaft position sensor or cam position sensor giving a bad signal to the ecu/pcm. Good luck.

Sep 01, 2015 | Cars & Trucks

2 Answers

Ford Escape 3.0 no power to #4 coil


Need to change the coil. Is likely the problem. Sometimes that means replacing the whole coil pack.

Apr 10, 2014 | 2005 Ford Escape

1 Answer

Have a 1986 chevy celebrity tec4 an have no fire from coil ive replaced coil checked fuses an have power going to coil still no fire


ignition will trigger if signal from crank sensor, with hei spark plug tester ,read to coil wire and spark plugs wire if spark , depends wich engine
if c3i coil and module the module could be the problems you can check it before replace
hope it helps

Mar 29, 2014 | 1986 Chevrolet Celebrity

2 Answers

I dont have any spark. have power to the coil pack just nothing past that. what to do??


Check the crank shaft postioning sensor. If you are getting power to the coil pack and there is no power coming out of the coil pack the coil pack might be bad or have corrioson between the coil pack and the mount. Thanks

Mar 07, 2011 | 1999 Mitsubishi Eclipse

1 Answer

I'm not gettin power through my ignition or to my distributer therefore I'm not getting spark why is this?


Need to look at ignition module since it provides power to primary terminal of ignition coil. If there is no power to the primary coil, then no power to the second coil. If there is no power on the secondary terminal of ignition coil connecting to the distributor then there is no spark at spark plugs. Good luck

Sep 21, 2010 | Chevrolet Blazer Cars & Trucks

1 Answer

No spark runns fine then loses spark wait 10 minutes starts


The spark plugs receives power to spark from coil pack.Check the power at the coil pack and also check the voltage at the coil pack with meter.If the coil pack shows proper power as well as voltage then its fault in spark plugs.Otherwise its faulty coil pack.The coil pack receives power from battery.so also check the voltage of the battery it should be exact 12 volt.
If the battery shows low voltage then the battery needs to be re-charged.
Then check out.
Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 1992 Pontiac Bonneville

1 Answer

My nissan


If you have a 12 volt test light put the point on the positive lead to
the coil and the ground lead to a good ground ( Negitive side of battery ). Then turn the key on. If the test light comes on then you have power to the coil. With power to the coil confirmed have someone crank the engine and put the test light on the negitive side of the coil. The light should flash at a rapid steady rate. If not then your pickup in the distributor may be bad. If no power to coil with key on or when cranking you may have a bad ignition switch.
Another way to test for spark is to remove the coil wire from the dist cap and hold the end close to a ground ( 1/4 inch away) and
have some one crank the engine. If you get a good spark but no
spark to the spark plugs you may have a cracked dist cap or a bad rotor. If no spark at coil wire use a wire in place of the coil wire to check for spark. You may have a bad coil wire. Good luck. Neil W.

Dec 24, 2008 | 1983 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...