Question about 2005 Toyota Corolla

1 Answer

Change rear wiper on toyota matrix

Where is the clip release

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 36 Answers

There no clip, is kinda tricky but you just have to bend the blade back until reach about 90 degree angle then slide down.

Posted on Mar 30, 2009

5 Suggested Answers

  • 2976 Answers

SOURCE: Rear Wiper replacement

Normally, all you need to do, is lift the arm and slide a small locking tab into place. Then, just lift the arm off. If it doesn't work like this, it has a screw in the center.

Posted on Aug 06, 2009

  • 18 Answers

SOURCE: Rear windscreen wiper V70 1998

Pull, and the plastic clips will disengage.  Some will break, there is nothing you can do about that.  Best to make a run to the dealer and pick up a handful of extra clips for the ones that do break.  There are tools that help prevent the clips breaking but they'll still break and it's not worth it.

Posted on Aug 22, 2009

Testimonial: "Thanks managed to get it off without breakage - another handy tip use a push knife under the rear portion of the internal release moulding to assist"

michigan man
  • 3533 Answers

SOURCE: Need to replace rear wiper blade. Purchased

give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your local Toyota dealership in the service department and some one will help you wish you the best of luck Michigan Man.

Posted on Nov 27, 2009

  • 36 Answers

SOURCE: how to change front pads on 2006 toyota matrix

http://us.toyotaownersclub.com//index.php?s=bb18602e7ff4236dab25828b356169e0&showtopic=141&pid=7424&st=0&#entry7424

here you can find detail instructions and pictures. Have Fun!!

Posted on Jan 13, 2010

  • 62 Answers

SOURCE: I have a 2004 Toyota Matrix with rear brake drums....

First: make sure the emergency brake is not applied. Second: over time the drum wears inside where the brake linings make contact, which makes an outer ridge. You will have to retract the brake linings to clear that ridge. Look on the back side of brake, and there should be a slotted access port to loosen the linings. If present remove cap cover, then insert wide blade flat screw driver to manually turn a star type toothed gear. Note: you will not be turning the screw driver, but making muliple up and down prybar movements to turn that hidden gear. I am not certain which way loosens the linings on your model. You will have to try going clockwise or counter clockwise.

Posted on May 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Toyota matrix rear window wiper sometimes


try spraying some wd40 into the wiper axle.

Oct 06, 2014 | Cars & Trucks

1 Answer

2003 toyota sienna van rear wiper not working


Either the linkage from the motor to the arm is broke,or a clip has came off and needs to be put back on.

Apr 26, 2012 | Toyota Sienna Cars & Trucks

1 Answer

I installed a new wiper motor. I ran it before installing the wiper arms. it will not stop at zero. it over travels down into the cowling. I try to rest them higher then they stop some where in the middle...


Try to run the motor without the wiper arms tightened down and turn it off so it can cycle down to its rest state. Then install the wiper arms.

Make sure, that the car's windshield wiper wiring is correct for this motor.
---
Wiper Arm & Blade Removal & Installation Front To Remove:
CAUTION
When the wipers are parked (off), the driver’s wiper arm must be above the passenger’s wiper arm.
  1. Remove the clip holding the outside end of the wiper arm cover to the arm.
  2. Lift the arm cap up to expose the nut.
  3. Remove the wiper arm mounting nut.
  4. Using a suitable two jaw puller, remove the wiper arm from the wiper pivot.
To Install:
  1. Verify that the wiper motor and linkage are in the parked position.
  2. Place the wiper arm in position over the wiper pivot.
  3. Install the nut to hold the wiper arm to the wiper pivot. Torque nut to 26 ft. lbs. (35 Nm). CAUTION
    Make sure to tighten the wiper arm nut properly.
  4. Push the arm cap cover down.
  5. Secure the clip holding the cover to the wiper arm.
Rear To Remove:
  1. Lift and hold the wiper arm away from the rear window.
  2. Lift the lock securing the wiper arm to the pivot.
  3. Slowly release the wiper arm so it rests against the lock.
  4. Remove the wiper arm from the pivot.
To Install:
  1. Install the wiper arm on the pivot.
  2. Pull the arm outward and release the lock.
  3. Gently release the wiper arm until it rests on the rear window.
prev.gif next.gif

Aug 22, 2010 | 1996 Dodge Grand Caravan

1 Answer

How do you remove a rear windshield wiper blade from a Toyota Highlander year 2008


This is a dealer only change. front are standard 26 and 20 inch clip on

May 07, 2010 | 2008 Toyota Highlander

1 Answer

How do you change the rear wiper blade


Easiest thing to do is buy the OEM replacement whole assembly from Advance Auto Parts like I did. One snap click, 10 seconds and your done.
Trico 12A.

http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_Exact-Fit-Wiper-Blade-Trico_20190000-P_326_R%7CGRPWIPEAMS_617335222____

Mar 12, 2010 | 2009 Toyota Matrix

1 Answer

How to change rear wiper motor?


Take the metal Wiper Arm up off the window.
These are held-on by a "U" clip on the Blade which is snapped into the "U" shape of the metal Arm.
On the Plastic "U" clip is a Release Tab.
Press the Release Tab while pulling the Wiper Blade (not arm) out of the "U" of the Arm.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!
FYI: Sometime the Arm and/or Blade gets bent or warped, causing it not to make full contact with the window. People change their Blade, only to find out their Arm was warped. Inspect this and adjust the Arm (gently) if this is the case.

Jan 20, 2010 | 2000 Dodge Caravan

1 Answer

Need to replace rear wiper blade. Purchased assembly from Toyota and can't find clip to release old blade from arm.


give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your local Toyota dealership in the service department and some one will help you wish you the best of luck Michigan Man.

Nov 27, 2009 | 2005 Toyota Highlander

1 Answer

How to replace the wiper insert at the back of


moz-screenshot.jpg
  1. REMOVE RR WIPER BLADE
    1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
    2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

  1. REMOVE REAR WIPER RUBBER
    1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
f54b10a.gif
  1. INSTALL REAR WIPER RUBBER
    1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
0dd144d.gif
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
8f40009.gif
c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

Sep 12, 2009 | 2005 Toyota Matrix

1 Answer

Rear windscreen wiper V70 1998


Pull, and the plastic clips will disengage.  Some will break, there is nothing you can do about that.  Best to make a run to the dealer and pick up a handful of extra clips for the ones that do break.  There are tools that help prevent the clips breaking but they'll still break and it's not worth it.

Aug 08, 2009 | 1998 Volvo V70

1 Answer

2006 Toyota Highlander


just how you remove your front wiper blades, they are the same.

different clips, different solutions.

if the rod's end is bend as a "u" shape, then press the plastic in the middle of the "u" and pull it downwards towards the back shield.

if the rod's end is just straight, push the clip downwards and this time, pull the wiper blade outwards , away from the back shield.

tnx 4 using fixya,

drcool

Sep 14, 2008 | 2006 Toyota Highlander

Not finding what you are looking for?
2005 Toyota Corolla Logo

Related Topics:

970 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...