Question about 1993 Dodge Caravan

1 Answer

1993 dodge caravan transmssion

After removing all of the bell housing bolts and mounts on trans, does the halfshaft have to be removed in order to get between housing and block to repair freeze plugs?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

No they make special tools but if you want to make it easy on yourself yes.. or get a rental tool with the right curve and cup size to install hammer needed to tap in with special tool for freeze plugs. Also keep in mind if your just replacing one its quick but if all are rusted or you think there are always doubt there are some in the middle of the housing and motor side behind your flywheel and diffrent sizes two.

Posted on Feb 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the transfer case in a 1999 dodge grand caravan


need to drop the cradle down leaving the engine and transmission suspended in the vehicle pull both half shafts disconnect shifter and wiring pull the exhaust pipe from front manifold to rear and and drop starter pull shield between engine and transmission and pull the three or four torque convertor bolts pull 18mm bell housing bolts and and trans mount tilt engine and trans to drivers side (support engine) and separate

Oct 30, 2015 | 1999 Dodge Grand Caravan

1 Answer

91 continental remove trans


Disconnect battery remove drive shaft, remove starter ,remove mounts undo bolts around bell housing,leave one bolt in so it won,t fall out, remove speedo wires and trans pipes if auto undo bolts to convertor put a floor jack under it and ,then remove the remaining bolt lower Trans down.

Aug 12, 2014 | 1991 Lincoln Continental

2 Answers

1996 grand caravan leaking trans fluid from bell housing i changed the seal at the front pump torque converter but still leaking


Here the thing you did the torque convertor seal but there is six bolts behind the torque convertor you take that out and remove the front pump housing, also the trans pan is famous for leaking all the time

Jun 08, 2011 | Dodge Grand Caravan Cars & Trucks

2 Answers

How do i change a flywheel on a 1993 chevrolet k1500 pickup


remove trans bolts and slide trans back to gatn acces to fly wheel bolts u dont have to fully remove the trans.

Aug 23, 2010 | 1992 Chevrolet K1500

2 Answers

Cannot remove transmission


Did you remove the torque converter bolt's from the fly wheel, should be 4. You will have to turn the motor by hand to remove all the bolt's.

Jul 22, 2010 | 1999 Ford Escort

2 Answers

Hard time with transaxle to fix clutch


ok this is fun

you need to remove the strut lower ball joint and the trans mount then remove the motor mount from front of opisite side frame rail to allow motor to rotate
then trans will drop about 4-6 inches undo the bolts slowely arround the bell housing when all bolts out shake the bastard it will slowely slip off
remember to jack the car up high i usualy go 2 feet off the ground with swifts and geo remove the cluch cable and i believe the starter stays in place just need to undo the bolts \
this job takes about 3 hours start to finish trans drops out the botom and goes in the same way use a small jack to suport the trans untill all bolts out and dont forget to use your ball joint fork to pop the drive shafts out of the trans and btw use new fluid to replace3 your losses on the ground c
and if all else fails buy a chilton book they are a god send

May 23, 2010 | 1993 Geo Metro

1 Answer

Locate bolts to remove the strater of 1996 dodge caravan


Almost all starters have ears with holds in them that bolts go through to threaded holes in the bell housing. Find the starter and look around the end without the wires for the bolts.

May 07, 2009 | 1996 Dodge Caravan

1 Answer

Removal and installation of an auto trans in 2002 toyota camry


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the transaxle fluid.
  3. Remove or disconnect the following:

    Negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding Battery Air cleaner assembly Throttle cable from the throttle body Cruise control actuator cover and connector, if equipped Ground wire Starter Speed sensor connectors, direct clutch speed sensor, and the park/neutral position switch connector on the transaxle Solenoid connector on the transaxle Shift control cable Oil cooler hoses Front side transaxle mounting bolts Front engine mounting bolts Oil cooler line mounting bolts from the front frame Upper transaxle to engine mounting bolts

    0900c15280197a59.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Tie the steering rack to the engine support fixture components, as shown-Avalon and Camry
    Front exhaust pipe Engine side covers and undercovers Both halfshafts Front side engine mounting nut Rear side engine mounting bolts (remove hole plugs) Left side transaxle mounting bolts Steering gear housing Front frame assembly Rear end plate mounting bolts Torque converter cover Torque converter retaining bolts Remaining transaxle mounting bolts Transaxle

Apr 09, 2009 | 2002 Toyota Camry

2 Answers

Getting space between trans and block 1993 caravan 3.0


unfortunately the only answer is to take the trans out of your way. you would need plenty of space in order to pry out old freeze plug and hammer in new one, of course with freeze plug installer.

Feb 27, 2009 | 1993 Dodge Caravan

1 Answer

Hello Friend, I have a Dodge Caravan 1997 and in the process of changing out my water pump and timing belt. I am in the stage where I need to open the damper harmonic bolt. Which direction does this bolt...


I have managed to open the harmonic damper bolt. This bolt opens in the counter clockwise rotation. A breaker bar was used with the flywheel locked in place. In order to get to the flywheel, the starter motor was removed to get access. The manual suggest removing the bell housing plate. This takes more effort and one of side engine mount also need removal. I decided to remove the starter motor instead. In order to remove the starter motor, first remove the cables from the starter motor and three mounting bolts. Secure a rod or a screw driver between the flywheel and bell housing through a hole in the flywheel. The size of the size is about 1/2". This hole was visible when the engine is set to TDC (top dead center). There could be more than one hole but I did not try to rotate the engine to find out. Once the rod or the screw driver in place in the flywheel, use the 22mm socket head and breaker bar and undo the harmonic damper bolt counter clockwise (CCW). I believe an impact air gun could do this job as well. The spec on the bolt is 100 ft lbs torque - Hendry

Jan 13, 2009 | 1993 Dodge Caravan

Not finding what you are looking for?
1993 Dodge Caravan Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...