Question about 2001 Chevrolet Impala

1 Answer

Check engine licht on and high idle

I have replaceed maf sensor and idle air contrl valve faut code 1635 still active any suggestions

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 463 Answers

Vacuum leak?

Posted on Feb 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2004 buick rendezvous idle at 3000 rpm and put in gear it drops to 1500 rpm and shifts hard while driving due to high engine speed?


Stuck throttle plate . gummed up with varnish or a problem with IAC valve . IAC - idle air control valve ! Videos on youtube , how they work how to clean . Idle Air Control Valve Could have unmetered air entering the engine pass the MAF sensor , a bad MAP sensor ! I would check the throttle plate first , if dirty clean it . Then check IAC valve if not the throttle plate . GM Idle Air Control IAC Function Diagnostics and Repair

Dec 14, 2016 | Buick Cars & Trucks

1 Answer

Code p1506


P1506 - Idle Air Control (IAC) Overspeed Error This DTC is set when the PCM detects engine idle speed that is greater than the desired rpm.
  • IAC circuit short to GND
  • Damaged IAC valve
Disconnect IAC valve and look for little or no change in engine rpm as an indication of a stuck or damaged valve.
Ford Idle Air Control IAC valve test how to adjust minimum idle speed
Ford Idle Air Control Valve Diagnostics High Idle DTC P1506

Dec 05, 2017 | 2000 Ford Explorer

1 Answer

I just got my car scanned and a few codes pop up


Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .


Apr 30, 2013 | 2004 Honda Civic

2 Answers

My 1998 chevy lumina ls is runnig rough at idle


Rough idle could be the throttle position sensor, or the idle air control valve.abs could be you need brakes or just the abs sensor is bad

Oct 10, 2017 | 1998 Chevrolet Lumina

3 Answers

My 2004 toyota tacoma has a rough idling problems and I was told to replace MAP sensor. Now, would it be Mass air flow sensor ? Because I can not locate any info on MAP sensor of this yeat truck


Yes your truck is equipped with a mass airflow sensor (MAF). However, I would not just replace that because its running rough. I would begin diagnostics by first checking to see if there were any trouble codes in the engine to give you a clue as to the rough running condition. I would expect a trouble code to be present to support the descision to replace the MAF Sensor. If no codes are present I would suggest that you get the vehicle tuned up. (Spark plug replacement and throttle body cleaning and I would also suggest removing the idle control valve and cleaning the carbon and dirt out of it. Although what you were told might be correct I dont belive that is where I would start.

Feb 18, 2011 | 2004 Toyota Tacoma

2 Answers

It idles very low and then dies, it drives but very very slow 0 pick up


lots of possibilities
in no particular order...
  • MAF sensor (Mass Air Flow)
  • TP sensor (throttle Position)
  • IAC motor (Idle Air Control)
  • Torque converter
  • restricted exhaust
  • IAT sensor (Intake Air Temperature)
  • EGR valve (Exhaust Gas Recirculation)
  • Restricted fuel flow
  • clogged intake
  • burnt valves
However, based on the low idle and slow acceleration I am leading towards the MAF

Have you been to the parts store and replaced anything yet?

Has anyone "pulled" codes?


Please update and let me know how else I can assist you today!
Sean

May 28, 2010 | 1997 Ford Escort

2 Answers

Jaguar xj6 4.0 1990. showing fault code fuel 14, fail 14. what does this code mean ?


2 airflow sensor out of operating range 3 coolant temp sensor out of operating range 4 oxy sensor indicates full rich 5 throttle potentiometer/airflow sensor... (low throttle pot signal with high airflow sensor signal) 6 throttle pot/airflow sensor...... (high throttle pot signal with low airflow sensor signal) 7 throttle pot...idle fuel adjustment failure(idle speed??) 8 intake air temp sensor...open or shorted circuit to sensor 11 Throttle pot at idle: Throttle pot idle trim out of normal range 12 Airflow meter: MAF signal out of range 14 Coolant thermistor: Resistance out of range or static during engine warm up 16 Air thermistor: Resistance out of range 17 Throttle pot: Out of range 18 Throttle pot/Airflow: Low throttle pot signal at high airflow 19 Throttle pot/Airflow: High throttle pot signal at low airflow 22 Fuel pump drive: ECU output to fuel pump relay 23 Fuel supply: Engine running too rich 24 Ignition Drive: ECU output to ignition Amp 26 Air leak: Engine running too lean 29 ECU self check 33 Injector Drive: ECU output to injectors 34 Injector: Looks for Injector dribble 37 EGR Drive: ECU output to EGR switching valve 39 EGR check sensor: EGR not working (normally pipe blocked) 44 Lambda (O2) sensor: Poor mixture control rich or weak (or misfire) 46 Idle speed Control valve: ECU output to Coil AB 47 Idle speed Control valve: ECU output to Coil CD 48 Idle Speed Control Valve: Stepper motor grossly out of position 66 Air pump: ECU output to air pump relay 68 Road speed sensor: Seen speed < 5km/h at high engine airflow 69 Drive/Neutral switch: Seen cranking in "D" or high airflow in "N" 89 Purge Valve drive: ECU output to purge valve
this is all I could find

Nov 09, 2009 | 1990 Jaguar XJ6

3 Answers

2003 ford taurus idle problems had trouble codes


A code P0174 may mean that one or more of the following has happened:
  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filters can cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor. and your solutions are.
    • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner . Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
    • Inspect all vacuum and PCV hoses, replace if necessary
    • Check for a dirty fuel filter and proper fuel pressure

Oct 24, 2009 | 2003 Ford Taurus

1 Answer

Fault codes, p0102,p0122,po507


po102--maf sensor, could be a bad air cleaner and not letting air into engine, po122--tps pedal position sensor low, replace or adjust tps sensor,or wiring,po507--idle control system high input. for this you can take off idle air control, and clean out carbon from were it mounts on engine. it is just before throttle body at end of air intake hose, it is black. do not push on pintle on end of valve when cleaning, use a old toothbrush to clean carbon off of valve, use carb cleaner but do not soak valve in liquid of any kind. good luck!!

Mar 20, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
2001 Chevrolet Impala Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...