Question about Toyota Xtracab

Open Question

Removing ashtray mounting 2008 Hilux. I want to mount my voyager electric brake controller where the ash tray is mounted. I can see the retaining bolts but they are covered by bits of the dash

Posted by on

  • jakencb Apr 22, 2009

    I am trying to do the same thing.  From what I understand is that you need to remove the middle dial knob from air conditioning unit.  Behind this is a screw.  Once this is out then you need to pull your glove box out.  Just open it the gently pull it up, the bottom lugs of the glovebox click off, then you can remove it.  Look under the bottom of dash and you can see lugs that attach the dash on..


    I have yet to do it but will be hopefully this week.  Maybe this will help

×

3 Suggested Answers

Technopro
  • 243 Answers

SOURCE: install front motor mount

Probably you have to loosen the rear mounting as well so that you can get a little bit more play in the movement to fir the bolt in.
Cheers

Posted on Oct 28, 2008

  • 3 Answers

SOURCE: 2001 S60 Volvo Engine Mount

yes,, do exactly as you describe

Posted on Nov 26, 2008

dennymulford
  • 1055 Answers

SOURCE: allen wrench size to fit caliper mounting bolt

some are 7/16 and some are 3/8 amd some are torx

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove a radio from a 1993 suzuki sidekick


well thats in the FSM. easy peasy
stock radio , we cant do non stock. (vast )
i guess step 4 is it?

heater control page.
  1. Disconnect the negative battery cable.
  2. If equipped, disable the air bag system. (skip)
  3. Carefully pull the knobs off of the control levers.
  4. On Sidekick, Tracker, Sidekick Sport and X-90 models, grasp the trim panel and pull it off of the instrument panel.
  5. stop.... here.
radio out
electronic version not analog
remove ash tray, and hidden tray screw and tray guide

  1. Pull the heater control lever knobs off of the levers.
  2. On 1996-98 models, separate the heater control trim panel from the control unit by pulling it straight away from the instrument panel. Allow the trim panel to hang loose.
  3. Open the ashtray, then depress the ashtray retainer and remove the ashtray from the sliding track. While it is removed from the vehicle, now would be a good time to wash it out.
  4. Loosen the two retaining screws, then remove the ashtray track from the instrument panel center trim bezel.
  5. On 1989-95 Sidekick and Tracker models, remove the trim panel (Bezel) by prying it carefully away from the instrument panel.
  6. On 1996-98 models, remove the center trim bezel from the instrument panel by loosening the four retaining screws and maneuvering the heater control trim through the appropriate hole. Set the bezel out of the way.
  7. Use a screwdriver to loosen the one rear mounting bracket-to-radio screw; access can be gained to this screw through the ashtray hole.
  8. Remove the four radio front retaining screws, then pull the radio out of the instrument panel just far enough so that the electrical connections on the rear of the radio can be accessed.
  9. Detach and label the wiring from the radio. Also, detach the antenna cable from the rear face of the radio
  10. pull radio. now. (if stock if not stock look for locks)


step 5
25477768-tiechxycrusckuccgw3t0yzs-2-0.jpg

Feb 25, 2015 | 1993 Suzuki Sidekick

1 Answer

How to remove the ash tray in a 1998 ford taurus lx


Ash Receptacle Console Mounted
Removal
  1. Remove beverage holder by carefully unsnapping front portion using a flat-blade screwdriver. Grasp beverage holder and unsnap from console panel (045A36) .

    swh~us~en~file=k23657a.gif~gen~ref.gif
  1. Open ash receptacle (30702) and move gearshift lever (7210) to 1 position.
  1. Grasp console top panel (044D90) and pull rearward to unsnap from console center finish panel. Disconnect electrical connectors from cigar lighter socket and retainer (15055) and lamp assembly.
  1. Remove console top panel from vehicle.

    swh~us~en~file=k23664a.gif~gen~ref.gif
Installation
  1. Follow removal procedure in reverse order.
Instrument Panel Mounted
Removal
  1. Disconnect battery ground cable (14301) .
  1. Open ash receptacle .
  1. At RH rear of ash receptacle, disconnect electrical connectors to cigar lighter socket and retainer .
  1. Depress locking tab on LH rear and RH rear corners of ash receptacle toward center and pull ash receptacle from instrument panel (04320) .
  1. Unscrew retainer from socket and remove cigar lighter socket and retainer .
Installation
  1. Follow removal procedure in reverse order.
c3090c04-8e43-44a7-8627-af5c7da3b8d1.gif

Sep 19, 2014 | 1998 Ford Taurus

1 Answer

Removing heater core


This is for a 2.3L
Hope this helps, it it does please leave feedback Thank You and Good Luck

REMOVAL
  1. Disconnect battery ground cable.
  2. Drain cooling system.
  3. Raise and support vehicle.
  4. Disconnect heater hoses from heater core assembly.
  5. Remove drain tube.
  6. Lower vehicle.
  7. If equipped, remove console as follows:
    1. Apply parking brake and block drive wheels.
    2. Position transaxle shift lever in Neutral.
    3. On models with automatic transaxle, remove clip retaining shift lever handle to lever, then remove shift lever handle.
    4. On models with manual transaxle, turn shift lever handle counterclockwise to remove from lever.
    5. On all models, carefully pry upward on outer edges of console trim plate.
    6. Disconnect electrical connectors and ashtray lamp from console trim plate, then remove trim plate from console.
    7. Remove console to mounting bracket attaching screws, then remove console.
  1. Right and left sound insulators.
  2. Steering column opening filler.
Floor Air Duct Outlet 58917672

  1. Floor air outlet duct.
  2. Heater core cover.
  3. Heater core mounting clamps and remove heater core.
INSTALLATION
  1. Heater core and heater core mounting clamps.
  2. Heater core cover.
  3. Floor air outlet duct.
  4. Right and left sound insulators.
  5. Console.
  6. Steering column opening filler.
  7. Raise vehicle.
  8. Heater hoses to heater core.
  9. Drain tube to heater case.
  10. Lower vehicle.
  11. Negative battery cable.
  12. Fill cooling system and check for leaks.

Jan 01, 2011 | 1994 Pontiac Grand Am

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

Replace rear brake pads


Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
rear_brake_pads.jpg Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
rear_brake_pads_2.jpg To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
rear_brake_pads_3.jpg After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
rear_brake_pads_4.jpg With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
rear_brake_rotor.jpg Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
rear_brake_rotor_2.jpg Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
rear_brakes_7.jpg Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
rear_brake_rotor_3.jpg After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
rear_brake_rotor_4.jpg Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

Jun 01, 2010 | 1995 Saab 900

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

How do I remove the front rotors from my 1999 honda accord


Removal & Installation

d4d9fd4.gif
After removing the caliper body, unfasten the retaining bolts and remove the caliper mounting bracket, in order to remove the rotor

  1. Use a siphon or clean turkey baster to remove about half of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle and remove the tire/wheel assembly.
  3. Remove the caliper mounting bolts, then lift the caliper assembly away from the brake rotor.
  4. Use a suitable piece of wire to suspend the caliper assembly. This will prevent the weight of the caliper from being supported by the brake flex hose which will damage the hose.
  5. Once the caliper body and brake pads are removed, unfasten the caliper bracket mounting bolts, then remove the bracket from the rotor.
  6. Remove the rotor retaining screws.
  7. Remove the brake rotor by pulling it straight off the wheel mounting studs or if seized in place, remove the stubborn brake rotor by threading in two 8 x 1.25mm bolts, two turns at a time until the brake rotor is released.
To install:
  1. If necessary, completely retract the piston into the caliper using a large C-clamp or other suitable tool as provided in the front disc brake pad replacement procedures in this section.
  2. Install the brake rotor onto the wheel hub and tighten the mounting screws.
  3. Install the caliper mounting bracket and secure with the retaining bolts.
  4. Install the caliper and pad assembly over the brake rotor and mounting bracket and install the mounting bolts.
  5. Fill the master cylinder to the proper level with fresh brake fluid.
  6. Install the tire/wheel assembly and lower the vehicle.
  7. Pump the brake pedal until the brake pads are seated and a firm pedal is achieved before attempting to move the vehicle.
CAUTION Do not move the vehicle until a firm pedal is obtained.

  1. Road test the vehicle to check for proper brake operation.

Nov 01, 2009 | 1999 Honda Accord

1 Answer

* * * Removal of Interior Trim Panel * * *


There are 2 finish covers on each side,looks like the one on the left is directly over ash tray?
You have to remove these 2 covers and there will be a screw located there. Remove these 2 screws remove the upper center finish panel by pulling outward to release the panel retaining clips.

Jan 30, 2009 | 2008 Ford F 250 Super Duty 4WD

2 Answers

Dash


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the ashtray.
  3. Unfasten the accessory trim plate screws, then remove the accessory trim plate.
  4. Remove the glove box door strap, then remove the glove box hinge screws.
  5. Remove the glove box door frame.
  6. Loosen the ashtray support screws, then remove the ashtray support.
  7. Remove the glove box.
  8. Unfasten the radio bracket bushing nut, then remove the radio.
  9. Disconnect the speaker grille screws, then remove the speaker grilles.
  10. Loosen the speaker retainers, then remove the front radio speakers.
  11. Unfasten the sound insulation panel screws, then remove the sound insulation panels.
  12. Loosen the steering column filler screws, then remove the steering column filler.
  13. Disconnect the hood release cable.
  14. Disconnect the shift indicator cable from the column bowl.
  15. Disconnect the steering column support nuts, then lower the steering column. For details regarding this procedure, please refer to of this guide.
  16. Unfasten the switch plate trim screw, then remove the switch trim plate.
  17. Disengage the electrical wiring harness from the rear defogger and the light switches.
  18. Disconnect the heater and A/C control.
  19. Disconnect the cluster housing bezel mounting nuts, then remove the bezel.
  20. Remove the instrument cluster from the vehicle. Disconnect and allow to hang:
  21. The speedometer instrument panel electrical connector and the Vehicle Speed Sensor connector
  22. The courtesy lamps and the cruise control module
  23. The horn relay, multi-function alarm and the flasher assembly
  24. If necessary, remove the applicable computer control module.
  25. Remove the instrument panel-to-cowl mounts:
    1. Unfasten the screws from under the panel.
    2. Remove the instrument panel support.
    3. Unfasten the screws in the defroster outlets.
    4. Remove the ductwork, dash plugs, wire looms, and heater cables attached to the panel.
  26. Disengage any electrical connections/wires routed through the instrument panel, then remove the instrument panel from the vehicle.
To install:
  1. Install the instrument panel assembly to the cowl, carefully routing and connecting the electrical wires and cables.
  2. Connect the instrument panel-to-cowl mounts:
    1. Connect the ductwork, dash plugs, wire looms, and heater cables to the instrument panel.
    2. Secure the screws in the defroster outlets.
    3. Install the instrument panel support, then fasten the screws (located under the panel).
  3. Install the computer control module, if removed.
  4. Install the instrument cluster. Reconnect and mount:
  5. The speedometer and Vehicle Speed Sensor electrical connectors
  6. The flasher assembly, multi-function alarm, and horn relay
  7. The cruise control module and the courtesy lamps
  8. Install the cluster housing bezel using the mounting nuts. Tighten the nuts to 12 inch lbs. (1.4 Nm).
  9. Install the heater and A/C control.
  10. Engage the rear defogger and light switch electrical harness.
  11. Install the switch trim plate using the retaining screw. Tighten the screw to 12 inch lbs. (1.4 Nm).
  12. Raise the steering column to the mounting bracket, then install the steering column support nuts.
  13. Install the shift indicator column to the column bowl, making sure that the indicator is aligned.
  14. Connect the hood release cable.
  15. Install the steering column filler panel using the retaining screws. Tighten the screws to 14 inch lbs. (1.6 Nm).
  16. Install the sound insulation panels using the retaining screws. Tighten the screws to 14 inch lbs. (1.6 Nm).
  17. Install the front radio speakers and speaker retainers, then connect the speaker grilles using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  18. Install the radio and tighten the fastener to 12 inch lbs. (1.4 Nm).
  19. Install the glove compartment, then install the ashtray support using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  20. Install the glove compartment door frame, door and door hinge screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  21. Install the glove compartment door strap.
  22. Install the accessory trim plate using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  23. Install the ashtray, then connect the negative battery cable.

Oct 02, 2008 | 1989 Chevrolet S-10 Blazer

1 Answer

Removing stereo


right above the radio are two screws in the black plastic trim... then remove the ashtray and youll see two more.. pay attention to how the ash tray track goes in..

Aug 31, 2008 | 2002 Suzuki XL-7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

419 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...