Question about 1999 Jeep Grand Cherokee

1 Answer

Turn signals ...help

I have the same problem with the brake light on driver side when all other lights are on what to do about my turn signals they dont work all the time

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 37 Answers

Replace the socket that the bulb fit into because it might be burnt this will be a dealership item.

Posted on Mar 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If it is the blinker switch why do I not have brake light on right rear side as well as no turn signal


The brake light circuit runs through the blinker switch, which is how the turn signal is able to override the brake light.

Jan 13, 2015 | Seat Cars & Trucks

2 Answers

Dash and tail lights not workjng brake and turn signal on passanger side not working


The dash and tail lights are on two different circuits, and the brake and turn signals are on different circuits, so at least 4 circuits total.
I would start at the headlight switch and check for power on the first two issues.

Jan 18, 2014 | 1990 Buick Century

2 Answers

ELECTRICAL PROBLEM


take it to a body shop

Nov 27, 2013 | 2000 Dodge Stratus

2 Answers

Have a 89 ford ranger all lights work except brake lights. I replaced the switch, fuses are good and so are the bulbs. What else could be causing the brake lights not to work??


It could be the turn signal switch, since the brake wire travels through the turn switch after it leaves the brake switch and then goes to the bulbs. That is how you get a steady brake light on one side, and a blinking light on the turning side. The rear turn signal lights and brake lights share the same filament in the bulbs (and the same wire). The wire on the turning side has to first travel through the flasher relay.
If you have a test light, first check for power out of the brake light switch with the pedal depressed. Then check for power in and power out at the turn switch connector-power in on the brake light wire and power out on either of the wires going to the rear bulbs-if no power out, the turn switch is bad-brake pedal still depressed so you still have the signal.

Sep 17, 2013 | 1986 Ford Ranger 2WD

2 Answers

I have no break lights or turn signals


Turn signal tail lights and BRAKE LIGHTS NOT WORKING


It can be faulty brake light switch causing the problem or its blown brake light bulb. First check and confirm brake light lamp is working and that's not the case.

For turn signal not working it can be faulty turn signal switch or its issue with wiring:----


==========

To trouble shoot brake and turn signal related problem, check the help links mentioned below:-----


Click the link:----
1996 Buick Regal Grand Sport Brake light Switch Location? http://schematicsdiagram.blogspot.in/2012/04/1996-buick-regal-gran-sport-brake-light.html

-----------
No brake lights on Buick? http://schematicsdiagram.blogspot.in/2012/04/no-brake-lights-on-buick.html

----------
Brake lights not working on 1989 BUICK REGAL?

http://schematicsdiagram.blogspot.in/2012/04/brake-lights-not-working-on-1989-buick.html

-------
How to replace Brake light switch on Chevrolet Tahoe?

http://technoanswers.blogspot.in/2012/02/how-to-replace-brake-light-switch-on.html

---------------
How to replace Parking, turn, and Brake Lights on car?

http://schematicsdiagram.blogspot.com/2011/06/how-to-replace-parking-turn-and-brake.html

----------
Upper brake lights work, but low brake light not working?

http://schematicsdiagram.blogspot.com/2011/12/upper-brake-lights-workbut-low.html

------------
1997 Cadillac Catera: How to replace Brake Light Switch?

http://howtobyme.blogspot.in/2012/06/1997-cadillac-catera-how-to-replace.html

------------


2003 Chevrolet S10 Tail light Fuse http://schematicsdiagram.blogspot.com/2012/11/2003-chevrolet-s10-tail-light-fuse.html

---------
Chevrolet Parking light and Tail lamp light Wiring diagram http://schematicsdiagram.blogspot.com/2012/11/chevrolet-parking-light-and-tail-lamp.html

----------
Car Tail Lights Not Working?

http://schematicsdiagram.blogspot.com/2011/12/car-tail-lights-not-working.html

----------
Turn Signal Not working http://technoanswers.blogspot.com/2012/11/turn-signal-not-working.html

----------
Right turn signal not working on Pontiac Car?

http://schematicsdiagram.blogspot.com/2011/12/right-turn-signal-not-working-on.html

--------
Only one side indicator light working on car?

http://schematicsdiagram.blogspot.com/2011/12/only-one-side-indicator-light-working.html

-----------
Turn signals not working on 1987 Jeep Wagoneer? http://schematicsdiagram.blogspot.com/2011/12/turn-signals-not-working-on-1987-jeep.html

1996 Chrysler LHS brake light circuit wiring diagram?

http://technoanswers.blogspot.in/2012/02/1996-chrysler-lhs-brake-light-circuit.html

----------
How to replace rear Brake lights on 2004 Toyota RAV4? http://schematicsdiagram.blogspot.in/2012/02/how-to-replace-rear-brake-lights-on.html

------------
One brake light on driver side not working, but other lights work?

http://schematicsdiagram.blogspot.com/2011/12/one-brake-light-on-driver-side-not.html

----------
2002 Lincoln Town car Fuse Box http://schematicsdiagram.blogspot.com/2012/11/2002-lincoln-town-car-fuse-box.html 2007 KIA Rio: Brake Light Fuse Box Diagram?

http://repairhelpcenter.blogspot.in/2012/06/2007-kia-rio-brake-light-fuse-box.html

-------------
Overhead Brake lights not working on 1999 GMC Sierra 4x4?

http://technoanswers.blogspot.in/2012/03/overhead-brake-lights-not-working-on.html

---------
2004 Ford Mustang: Brake light Fuse Location?

http://howtobyme.blogspot.in/2012/05/2004-ford-mustang-brake-light-fuse.html

---------

These will help.

Thanks.

Nov 24, 2012 | Cars & Trucks

1 Answer

No turn signals, 1 driver brake light bad, ABS light on. 2002/2003 CVPI


Sounds like you have 'ground' issues. Apply the brakes using a broom stick or more apropriate tool so that the brake lights are activated. Then go to the brake light that is not bright enough. using a test-light with a sharp pointed probe, poke the ground wire close to the bulb (usually a black wire) make sure the test light is attached to a grounded bolt. if the brake light gets brighter with ground added, you need a new ground wire. Splice it in to the existing wire & attach it to a bolt. Lights should work better with proper ground. (each bulb has a positive post & neg. post, don't add ground to the side with power coming through it from Battery (+)(red light on test light) - probe wires FIRST with test light to find (+) POS. Hot wire, and leave that one alone.

Aug 09, 2012 | 2003 Ford Crown Victoria

2 Answers

My brake light and signal light stopped working on my 1998 dodge neon on drivers side back can you help?


Does any lights on the right side work? It sounds like the ground connection to the assembly is loose.

Jan 04, 2011 | 1998 Plymouth Neon

2 Answers

Tail lights work on both sides. turn signal and


Sounds like you need to replace the drivers brake/tail light.

Dec 14, 2009 | 1998 GMC Sierra

1 Answer

The drivers side rear brake light/turn signal only not working


you replaced the bulb with the wrong one i.e. a two filament bulb with a one filament bulb

Oct 05, 2009 | 2006 Ford F-250 Super Duty

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...