Question about 1989 Ford Thunderbird

1 Answer

Need wiring pictures for door sensors the ding button

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

What make and model

Posted on Feb 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Constant dinging sound whenever the key is in the ignition. all doors are closed, and still the ding, one every second, until the car is off. continues no matter how long the ride is. 45 minute trip and...


These can be annoying and hard to find, Since it's a 2 door , check the buttons that the door hits when closing. Snap them in and out several times and if you have it, soak them with something like WD40. Is a dashboard light on to give you a clue ? The ding might also be related to the seat belts. Make sure ALL are snapped into their sockets to test that. Last resort is cut or disconnect the wire that goes into the "ding" module. I would recommend a mechanic with a tester who can pin down the problem and it should not take more than a hour labor or around a hundred bucks.

Oct 20, 2013 | Ford Cars & Trucks

1 Answer

How can I disable the seat belt sensor because it continues to beep even if we are all buckled.


I wouldn't disable the sensor but are you sure it is a seat belt sensor dinging at you and not a door sensor? They both sound the same. With all the doors closed but the key in the ignition. If the warning ding starts then your problem is a door sensor, a common issue in that model and usually related to the side door.

Nov 04, 2011 | 2001 Ford Windstar

1 Answer

I have a problem with my 2001 sebring lxi. It makes a ding sound ( the same ding as when the gas gage light comes on) when it dings the odomiter reading goes off and the word (deck) appears. If you push...


It is saying your trunk lid/trunk sensor is open, unlatched or the sensor is not functioning properly. Check the wiring going to your trunk lid sensor, make sure it is clean and not corroded. Sometimes a good cleaning will do the job.

May 02, 2011 | 2001 Chrysler Sebring

1 Answer

I own a 2007 montana and had it for 1 month now ..It keeps making a ding ding ding chime while driving ..The passengers rear door is automatic and when I press the button it makes the same noise but when...


1. Turn off the overhead over-ride switch. Drive again. Do the chimes stop? If yes, the door is not closing properly due to the door contacts. Clean them yourself or have them serviced.
2. If the chimes did not stop in step 1. above, it's not likely the door but rather something else.
3. Chimes occur for many reasons. Suggest checking - a. are the rear back-up warning sensors blocked/dirty? b. any other lights on the dash like oil, abs, airbag, etc? c. passenger side airbag disabled - something heavy placed in passenger seat?

In my experience, it's the automatic door contacts. We have a long history of problems with these auto doors, that are still not resolved. problems all throughout the warranty period, and now into the extended warranty period. We must unite and get GM to resolve the quality of these doors. My next step (next incident) is going to be to have the dealership inspect the entire wiring system.

Oct 14, 2010 | 2007 Pontiac Montana

1 Answer

Looking for a free link where i can find schamatic for electrical


Does the door ajar light come on when it makes the dinging sound? If so you probably have a stuck door sensor in the drivers door. The drivers door is the only one, I believe, that makes the dinging sound when it is opened when the ignition is on. Spray some WD-40 into the door latching mechanism and try to free up the micro switch, this is not a bad idea as preventative maintenance even if you are not having a problem.

Apr 03, 2010 | 1998 Ford Windstar

1 Answer

Annoying alarm dinging until van reaches 17mph


This means one of the door ajar sensors is stuck. You need to remove the door trim panel and then the latch and then the sensor. Once out clean and lube it. There is a sensor inside every door.

Mar 16, 2010 | 1998 Ford Windstar

2 Answers

How can i fix my car door from not dinging and


there is a switch inside the door that is called the door ajar switch, replace it

Nov 11, 2009 | 1999 Dodge Stratus

2 Answers

2006 Pontiac montana SV6 power sliding door sensor will not acknowledge door is closed and 'ding ding ding' is now heard in my sleep!!! I've had this to three different Pontiac dealers and nothing seems to...


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Sep 25, 2009 | 2006 Pontiac Montana SV6

3 Answers

Door ajar light & washer fluid light & bell dings,


sound like your fluid sensor may be stuck or bad if light stays on try tapping the washer motor on the resevoir if it goes out faulty sensor as for the door ajar light it might have bad connection with sensor saying the door is closed local dealer should be able to troubleshoot sensor

Aug 23, 2009 | 2003 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...