Question about 1993 Oldsmobile Cutlass Ciera

2 Answers

I need to locate and replace the multi function switch

1993 Olds Cutlass Supreme S
Both Turn signals light, but do not blink
Fuses are good
Bulbs all good
Turn Signal flasher replaced

None of these fixes have worked
Multifunctiion switch. Is it in the steering column and how do you go about replacing it?

Posted by on

  • drob504 Apr 25, 2009

    Just change out turn signal switch. Passenger side bulbs(front and rear) light when the right turn signal should be flashing. However there is no flashing, clicking...Now, what should I consider at this point. Before I changed out the turn signal switch the problem was: the passenger side would occasionally light but would not flash I had to flash them manually. Also, the brake lights would not illuminate when the brakes were pressed. The brake lights work fine now.

    Not afraid to do it myself.
    drob504@att.net

  • drob504 Apr 25, 2009

    1996 Cutlass Oldsmobile Supreme...Just changed out turn signal switch. Passenger side bulbs(front and rear) light when the right turn signal should be flashing. However there is no flashing, clicking...Now, what should I consider at this point. Before I changed out the turn signal switch the problem was: the passenger side would occasionally light but would not flash I had to flash them manually. Also, the brake lights would not illuminate when the brakes were pressed. The brake lights work fine now.

    Not afraid to do it myself.
    drob504@att.net

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My turn signal flasher was located to the right of the ash tray, I looked around the column for HOURS and it wasn't there... I also have an 93 oldsmobile cutlass ciera, it drove me crazy because the manual wasn't correct.

Posted on Mar 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

Are both signal on at the same time. If they come on like they should but just don't blink it is more likely a bulb or a flasher, not the switch. The Turn signal switch is in the column. You have to remove the steering wheel and lower dash cover, but you don't have to remove or completely disassemble the column.

Posted on Feb 27, 2009

  • Clint Smock
    Clint Smock Feb 27, 2009

    Make sure you replaced the turn signal flasher and not the hazard flasher. They look exactly the same. Turn on your hazards and listen for the click, that way you can determine that the other flasher is for the turn signals. The turn signal flasher is usually attached to the steering column near the brake pedal.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 olds cutless brake lights will not work. bulbs, fuse and switch are good


Its a faulty turn signal switch.Try this,push down and hold brake pedal while pushing on the hazard switch and if the brake lights come on then replace the signal switch.

Jan 29, 2012 | 1997 Oldsmobile Cutlass Supreme

1 Answer

1989 olds cutlass supreme. None of the brake lights work. All other lights work. Fuses are good.


You probably have a bad brake light switch. This switch is located on the brake pedal arm or a bracket next to the arm. This switch activates the brake lights when the pedal is pushed. You can check this by turning on your turn signals or warning flasher if your light flash in the rear. Your bulbs are good so this will bring you back to the brake light switch.
d870a.jpg

Feb 08, 2011 | 1989 Oldsmobile Cutlass Supreme

2 Answers

Brake and turn signals not working


usually this indicates that the brake light switch or turn signal or flasher have failed.i would start by replacing the brake light switch located on the upper area of brake pedal and fix ya problem. 

Jul 12, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

Have a 96 Olds Cutlass Supreme, brake lights will not work. We've replaced bulbs, fuses and brake light switch and still nothing. Help!


Try having someone push on brake pedal at the same time thay move the turn signal lever up and down slightly to see if your brake lights work this would tell me that you have a faulty turn signal switch because GM runs the brake lights thru the turn signal switch so they work if you are driving with your 4way flashers on.

Jun 06, 2010 | 1996 Oldsmobile Cutlass Supreme Coupe

2 Answers

92 olds cutlass supreme turn signal broken


Start by checking the fuses that's simple
than relay than bulbs
last you may have to remove the steering wheel and than replace the entire signal assembly those are pretty much all your options so start with 1 and work your way down the list

Sep 24, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

88 olds cutlass, no brake lights


Your brake light circuit runs thru your turnsignal switch if your hazard switch is on your column I have seen numerous inop brake lights caused by faulty turn signal switches.

Aug 23, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Both turn signals light, but do not blink


under the dash on the driver side there is a round or square sliver box that should say turn signal or flasher on it in the fuse box.

Feb 26, 2009 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

908 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...