Question about 2004 Chevrolet Silverado 1500 Crew Cab

1 Answer

Remote will not operate

My remote will not work and it appears that I have lost all power to the passenger door. Window, lock,seat heater..... The drivers door is fine except that I cannot raise or lower the passenger window. I have replaced the battery in the primary remote and tried it and the secondary remote with the same results. All fuses appear OK...

I'm baffled!!

Thanks

Larry

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

The passenger door control module might be bad. The window switches are built into the module.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the control module for the windows and locks etc.


The vehicle is equipped with power door locks. Each lock actuator is powered and controlled by the door module mounted in the individual door. The driver door module (DDM) is the master control for the door lock system but the rear integration module (RIM) contains the program that determines when the lock functions are permitted. ( RIM ) is rear integrated module , under the back seat . Also a fuse box is also located under the back seat.
The door lock operation modes are controlled by the rear integration module (RIM). The RIM examines the requested function from the DDM, or the remote function actuator (RFA), as well as the transmission shift selector position and the ignition switch position information available over the Class 2 serial data circuits. The RIM determines if a locking function is permitted, and commands the DDM to perform the function permitted. The DDM then sends commands to the rest of the door modules via the SBI to implement the selected locking function.
The vehicle is equipped with power windows controlled by the door modules. The DDM receives a window switch request, over the SBI serial data, from either the passenger door module wired to the window switch pressed or from the driver door switch assembly. The DDM checks the Class 2 serial data to see if the status information is correct (i.e. ignition switch position) to permit window operation.
Your best bet is take the vehicle to the dealer or a repair shop that knows how the system works . Are you familiar with GM class 2 serial data communication network ? You could inadvertently render your vehicle unable to start an run if the class 2 bus were to become shorted to ground .
You
Buick Class 2 Operation Diagnosis 1998

May 03, 2016 | 2000 Buick LeSabre

1 Answer

1993 Ford F150 4X4 Power door locks, power window on passenger side and lumbar control on seats stopped working


CK FOR POWER TO LOCK @ WINDOW SWITCH IT COMES FOR MASTER WINDOW SWITCH ON LEFT SIDE DOOR NOT SHORE ON LUMBAR CONN.UNDER SEAT CK IT FOR POWER

Aug 11, 2009 | Ford F-150 Cars & Trucks

1 Answer

98 chevy blazer power window issue


sugest fuse ck 1st thing. Master bypasses individual controls. Power supply to rear windows is interupted. Ck for connevtor under front seats. Fuse may be labrled accessory or per win.

May 12, 2009 | 1998 Chevrolet Blazer

2 Answers

2005 Chrysler Pacifica passenger doors have no power


If your alarm went off, it could be that someone had tried to break into your car. They most likely may have cut some of the wires inside your door with what ever device they may have been using. Look for evidence between the bottom of the windows and doors where the problem is. If not, then it is possible that your automatic window assemblies are malfunctioning. Do you hear the motors run on the windows when you go up or down with the switch? I also have a Pacifica, 2005, however no window problems yet.

Good Luck,

Ray

Apr 21, 2009 | 2005 Chrysler Pacifica

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

4 Answers

2004 Jeep Grand Cherokee driver side power windows do not work


I had the same problem with now power to windows, mirrors and seat. The common soulution is the orange and or black wire in the boot have broken between the door and post.

Nov 25, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...