Question about 2001 Chevrolet Impala

1 Answer

WHERE DO I LOCATE THE EGR VALVE ON MY 2001 CHEVY IMPALA 3.8 V6

Egr valve locatio

Posted by on

  • 1 more comment 
  • Anonymous Mar 14, 2014

    Find egr valve

  • Anonymous Mar 18, 2014

    need to replace the egr valve where is it located

  • Anonymous Mar 21, 2014

    Where is the egr valve in a 2001 Tahoe

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 333 Answers

The egr valve is located at the end of a hose that plugs into youe valve cover. It is pushed right into a rubber grommet that is located in one of the valve covers. I hope this helps. don.t forget to rate my nswer, thanks

Posted on Feb 27, 2009

  • Frank Russo Feb 27, 2009

    Sorry I misunderstood your question. I was thinking of the pcv valve. But now for you real question.The egr valve is usually located on the intake manifold or head. There is a diaphram in the egr valve. The valve uses manifold vacuum on the diaphram to lift or close a valve allowing exhaust gas to enter the intake manifold. An easy test for the diaphram is to remove the vacuum line that runs to the egr valve. You can normally reach the diaphram area with your finger. Move this opposite from the direction it normally sits at. Then cover the vacuum port located on the egr valve with a plugged hose or your finger. The diaphram should either stay in this other position or slowly move to the normal position. If it won’t hold vacuum and instantly returns to it’s origional position, either a vacuum port is still not plugged or the diaphram is leaking. If it is leaking replace the egr valve. If the egr valve holds vacuum then remove the valve from the manifold.












    window.google_render_ad();




    â





    window.google_render_ad();

  • nicholas meola Oct 01, 2013

    there is no vacuum hose attached to the ERG valve, this is a 2001 Acura MDX. only an electrical plug in

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p401 for chevy impala


Code 401 is for a problem with the EGR valve air flow. It could be the EGR valve or the sensor.

Aug 09, 2013 | 2007 Chevrolet Impala LS Sedan New Cars

1 Answer

Where is the egr valve located in my 2002 chevy impala 3.4


the EGR valve is located at the rear of the upper intake manifold, on the driver's side. It is electrically controlled and has a black plastic looking cylindrical cap with a wire connector at the top.

Feb 11, 2011 | 2002 Chevrolet Impala

1 Answer

I am looking for the location of the EGR valve on a 2204 chevy Impala 3.4 engine


EGR VALVE LOCATED ON DRIVER SIDE ITS A AROUND LOOKING THING SITTING NEXT TO MASTER CYLINDER IT HAS A SMALL FLEXIBLE METAL PIPE THAT CONNECTS TO IT AND THE EXHAUST MANIFOLD.

Jan 02, 2011 | 2004 Chevrolet Impala

2 Answers

Chevy 2002 Malibu ERG valve


Symptoms of a bad EGR valve are usually stumbling idle or the engine stalling when the car is warm (normal operating temperature). Find the EGR valve and locate the vacuum line attached to it. Start the engine cold and wait for it to warm up. When the engine starts to stumble, pull off the vacuum line. If the EGR is bad, the engine idle will stabilize and no longer stumble.

May 25, 2010 | 2002 Chevrolet Malibu

1 Answer

How do I locate and replace EGR valve?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT

REMOVAL PROCEDURE
1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
1.
Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.

Jan 30, 2010 | 2001 Buick Regal

1 Answer

Chevy Impala 2001 w/ 3.8L engine - EGR stuck open


there are a couple of things, first make sure there are not restriction in the exhaust, i know the dealer has had to replace converters under warranty because of this problem, then theres a reflesh program for the computer due to this problem, and lastly,run with egr off make sure it clean of carbon,carbon gets stuck in pintle sets check eng lightbut carbon then blows by so when you remove egr you see nothing, well start with these good luck.

Nov 28, 2009 | 2000 Chevrolet Impala

1 Answer

Car sputterd and stalled while driving.


ECU is the engine computer and the EGR valve allows exhaust gas to recirculate back into the intake manifold at certain times and is usually vacuum controlled. EGR valves are replaced fairly often because of the high heat from the exhaust. Check for a loose or damaged vacuum hose (or if an electrically controlled valve, look for loose wires, or connector). ECU faults may or may not require replacement of the unit. Have you replaced the fuel filter?

Jul 26, 2009 | 2001 Chevrolet Impala

3 Answers

FAILED EGR VALVE


The EGR valve helps your car more efficiently and completely burn fuel by recirculating a portion of your exhaust and running it through the combustion process again. This results in a cooler, more complete burn of the fuel which decreases you car's noxious emissions by prohibiting the formation of some harmful gases.

The EGR valve is vital to your car's emission controls.

When the EGR valve goes bad, it must be replaced - it cannot be repaired.

  • EGR Valve = Exhaust Gas Recirculation Valve.
  • The EGR valve controls formation of noxious emissions.
  • Rough idle and poor acceleration can be caused by a faulty EGR valve.

  • The EGR valve, or Exhaust Gas Recirculation valve, is a vacuum controlled valve which allows a specific amount of your exhaust back into the intake manifold. This exhaust mixes with the intake air and actually cools the combustion process. Cooler is always better inside your engine. The exhaust your EGR valve recirculates also prevents the formation of Nitrogen related gases. These are referred to as NOX emissions, and are a common cause for failing emissions testing. Unfortunately, your EGR valve can get stuck, causing NOX gases to build up. You'll know if your EGR valve is stuck or malfunctioning because your car will experience symptoms like rough idle and bucking on accelertaion.

    The only short term problem is a decrease in gas mileage - but it should really be replaced before sensors become sooted or your cat. convertor gets overworked prematurely.

    Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

    Apr 15, 2009 | Chevrolet Impala Cars & Trucks

    1 Answer

    EGR VALVE


    REMOVAL PROCEDURE
    1. Turn OFF the ignition.
    2. Disconnect the EGR valve electrical connector.
    3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back.
    4. Remove the EGR valve retaining bolts.
    5. Remove EGR valve assembly.
    6. Remove the gasket.
    INSTALLATION PROCEDURE
    1. Install the EGR valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions.
    2. Reinstall the bolts through the EGR valve into the intake manifold. Tighten Tighten the EGR bolts to 30 N.m (22 lb ft).
    3. Connect the exhaust pipe assembly to the EGR valve.
    4. Reinstall the exhaust pipe bolt. Tighten Tighten the nuts to 30 N.m (22 lb ft).
    5. Connect the EGR valve electrical connector

    May 28, 2008 | 2000 Chevrolet Impala

    Not finding what you are looking for?
    2001 Chevrolet Impala Logo

    Related Topics:

    2,951 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    63242 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21981 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...