Question about 2000 Oldsmobile Intrigue

1 Answer

Power Steering Pump?

What's the best way to replace a power steering pump in an 99' intrigue? I put fluid in daily and by the end of the night it's drained.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,674 Answers

May just be a line leaking, that can be repaired or replaced. Have someone put it on hoist and look for sure at what's wrong, may be cheaper & easier than replacing pump.

Posted on Feb 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pump replacement


Your going to have noises and fluid drop when you first do this project there is air in the system have you turned the steering wheel several times left to right while running to bleed the air and re check fluid level?

Jan 07, 2014 | 2004 Acura TL

1 Answer

2001 Chevy Silverado 3500 6.0L V8 4x4 Dually, I replaced the power steering pump about 2 months ago, now I have power steering fluid leaking from underneath drivers side dash and carpet is saturated, also...


This sounds like the hydroboost unit is leaking.behind the master cylinderThe braking system on this using the power steering pump to provide power assisted brakes instead of a brake booster. The hydroboost unit most likely needs replaced.

Apr 19, 2011 | Chevrolet Silverado 3500 Cars & Trucks

1 Answer

99 olds intrigue power steering belt very hot, I just replaced the power steering pump, it's makes a clicking sound and is getting very hot, sounds like it could be the steering colume.


remove the drive belt and check each pulley by hand for drag, or noise. Usually noises from the serpentine belt area are from the tensioner pulley, but since you installed a new PS pump I'd pay particular attention to that-also, watch the belt and pulleys for any 'wobble' too.

Apr 12, 2011 | 1999 Oldsmobile Intrigue

1 Answer

How to change vane pump o/h kit


FIRST OF ALL TURN OFF RADIO REMOVE NEGATIVE BATTERY CABLE. THEN REMOVE POWER STEERING PUMP FLUID FROM POWER STEERING PUMP.USING A HAND PUMP SIPHON. BE CAREFUL DONT GET POWER STEERING FLUID ON CAR PAINT IT WILL DAMAGE PAINT JOB.PUT A DRAIN PAN UNDERNEATH CAR TO CATCH POWER STEERING FLUID THEN DISCONNECT POWER STEERING PUMP LINES.REMOVE POWER STEERING PUMP ADJUSTER BOLT AND MOUNTING BOLT.REMOVE POWER STEERING PUMP.MOST OF THE TIME NEW POWER STEERING PUMP DONT HAVE DRIVE PULLEY ON IT SO TAKE TO A MACHINE SHOP THE WILL REMOVE PULLEY FROM OLD PUMP AND PRESS ON THE PULLEY TO NEW POWER STEERING PUMP.BESURE TO BUY NEW O RINGS TO END OF PRESSURE LINE.ONCE NEW POWER STEERING PUMP HAS PULLEY IN PLACE AND YOU HAVE NEW O RING FOR HIGH PRESSURE LINE.INSTALL NEW PUMP.ADJUST BELT TENSION.NOW BLEED POWER STEERING PUMP WITH FRONT WHEELS POINT STRAIGHT A HEAD POSITION.POUR POWER STEERING FLUID IN PUMP UNTIL FLUID LEVEL ON COLD MARK ON POWER STEERING PUMP DIP STICK.KEEP ADDING FLUID UNTIL FLUID STOP DROPPING. START THE ENGINE LET IT RUN AT IDLE ADD MORE FLUID IF DROPS KEEP FLUID ON FULL COLD MARK.ON DIP STICK TURN OFF ENGINE.CHECK TO MAKE SURE POWER STEERING PUMP NOT LEAKING AT THE LINES THEN.SAFELY RAISE SUPPORT FRONT OF THE VECHICLE WITH JACK STANDS. MAKE SURE VECHICLE ON SOLID LEVEL GROUND CHECK.FLUID LEVEL MAKE SURE AT FULL COLD MARK. NOW START ENGINE.LET IDLE MINUTE.THEN TURN STEERING WHEEL ALL THE WAY TO THE LEFT TO RIGHT SEVERAL TIMES WITH OUT STOPPING IT IN PLACE. CHECK POWER STEERING FLUID WHEN FLUID LEVEL STOP DROPPING.AND FLUID IS NOT A TAN COLOR WHICH MEAN LOTS OF AIR IN SYSTEM. TURN OFF CAR UNTIL AIR BUBBLES DISAPPEAR.CHECK FLUID LEVEL BLEED POWER STEERING AGAIN. DONT DRIVE VECHICLE UNTIL STEERING FEEL NORMAL.IF FLUID REMAIN TAN WITH AIR BUBBLES CHECK FOR LEAKS AT POWER STEERING PUMP PRESSURE HOSE ORING. AND CHECK POWER STEERING LINES TO PUMP FOR LEAKS.

Mar 07, 2011 | 2000 Honda Civic

1 Answer

Show me how to replace power steering pressure hose on 1995 GMC Yukon


It's very easy, undo screw one end from back of power steering pump, no need to remove pump, and unscrew other end of hose from steering gear box, replace hose and top off with power steering fluid, when you undo power steering hose have a pan to catch the power steering fluid that will drip out.

Aug 17, 2010 | GMC Yukon Cars & Trucks

1 Answer

Where do you add poersteering fluid on a 99 Oldsmobile Intrigue. I have searched everywhere and sadly can not find


Passenger side of the engine. The power steering pump is part of the top center pulley, there is a black reservoir attached to it. This reservoir is the power steering fluid reservoir.

Aug 10, 2010 | 1999 Oldsmobile Intrigue

1 Answer

Is it hard to change a 98 Olds Intrigue power steering pump for someone who's not a mechanic? We knew the pump was going but were waiting for money to replace. Then when refilling the fluid one day and...


Power Steering Pump Replacement

Removal Procedure
  1. Place a drain pan under the vehicle.
  2. Remove the fuel injector site shield.
  3. Remove the power steering pump pulley from the power steering pump.
spacer.gif 2008-08-27_145449_diag1.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif 4. Remove the power steering pump pressure hose (1) from the power steering pump.

5. Remove the power steering pump return hose from the power steering pump.
2008-08-27_145520_diag2.gif6. Remove the power steering pump mounting bolts.

7. Remove the power steering pump.
spacer.gif 2008-08-27_145611_diag1.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif 8. Remove the power steering pump reservoir from the power steering pump.

Installation Procedure
  1. Install the power steering pump reservoir to the power steering pump.
spacer.gif 2008-08-27_145711_diag1.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif 2. Install the power steering pump to the vehicle. Notice: Refer to Fastener Notice in Service Precautions.

3. Install the power steering pump mounting bolts. Tighten the power steering pump mounting bolts to 25 Nm (18 ft. lbs.).
spacer.gif 2008-08-27_145739_diag2.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif 4. Install the power steering pump return hose to the power steering pump.
spacer.gif 2008-08-27_145822_diag1.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif 5. Install the power steering pump pressure hose (1) to the power steering pump. Tighten the power steering pump pressure hose to 30 Nm (22 ft. lbs.).

6. Install the power steering pump pulley to the power steering pump.

7. Install the fuel injector site shield.

8. Bleed the power steering system. You can do this by removing the power steering fluid cap and lifting the front of the vehicle with jack stands. Turn the engine on and turn the steering wheel slowly lock to lock. This will take 5-10 minutes as you will see the power steering fluid foam up. This is bleeding the air out of the system.

9. Inspect the power steering system for leaks.


Nov 03, 2009 | 2000 Oldsmobile Intrigue

1 Answer

How to r&r powersteering pump 1998 mercury grand marquis


Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL
  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Oct 04, 2009 | 1998 Mercury Grand Marquis

1 Answer

I'm trying to replace the power steering pump on my acura integra 1994 how can i replace it


drain power steering fluid.disconnect the inlet and out let hoses from power steering pump.remove belt by loosen the adjusting bolts on pump bracket.remove power steering bolts and remove pump.put in new power steering pump torque it 17 ft lbs . connect hoses .put belt back on adjust the belt tension. add fluid check level . bleed the air from system.

Apr 13, 2009 | 1990 Acura Integra Hatchback

1 Answer

Power Steering


will be the pump. when it happens try revving the engine and turning steering it it gets lighter then definatly is pump

Feb 27, 2009 | 2002 Oldsmobile Intrigue

Not finding what you are looking for?
2000 Oldsmobile Intrigue Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...