Question about Hyundai Motor 1999 Tiburon

1 Answer

Can't get my alternator belt back on 1999 hyundai tiburon, and the alternator is slid all the way back toward the engine

Posted by on

  • dreamcar90 Feb 27, 2009

    thanks for reply, but i found the problem was that after jacking up the car, which wasn't easy in the hill driveway, i loosened the bottom nut on the alternator, and she slid up to firewall allowing easy placement of the belt.
    thanks again for your help...next time i might try that.


×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 60 Answers

IF your sure you have the correct replacement belt, AND your sure that you have the belt routed correctly, you could try bumping the belt on. CAUTION, DANGER, SEVERE INJURY MAY OCCUR. The method I'm about to describe is very dangerous, use extreme care if you attempt this method. You'll need two people and a long (preferably 2 or 3 foot long) prybar. First disconnect the coil wire so the car won't accidentally start. Next, you have to be able to get at least the first inch or two of the belt on the pully. If you can't get the belt that far, don't install it. Take it back and get a longer belt or you'll damage the alternator bearings. Once you get the belt to that point, place the blade of the prybay tightly against the belt, holding it against the pully. Keep your hands and fingers away from the engine compartment as much as possible and be ready to move quick. Have your helper bump the ignition key for just an instant. Just a very quick on/off of the key. It may take a few tries before the belt jumps onto the pully. If this helps you, please remember to rate my responce but most of all, BE CAREFUL!! Thanks.

Posted on Feb 26, 2009

  • VonZeppelen
    VonZeppelen Feb 28, 2009

    Great, thanks for the rating.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I adjust the tension on the alternator belt for my 2003 Hyundai Tiburon?


Adjusting alternator belt tension - bolt & pivot bracket design ...

? 13:06
https://www.youtube.com/watch?v=8JN0RtZk_2Y
Nov 26, 2012 - Uploaded by backyardmech
Releasing tension on the alternator belt to remove the alternator- 4 cylinder Honda in this video. ... How to ...

How To Install replace Alternator Belt 1999-06 Hyundai ...

? 4:51
https://www.youtube.com/watch?v=6IWgXTijclo
May 15, 2013 - Uploaded by 1A Auto Parts
How To Install replace Alternator Belt 1999-06 Hyundai Elantra 2.0L .... Adjusting alternator belt tension ...

Dec 21, 2015 | 2003 Hyundai Tiburon

2 Answers

Where is the alternator on a 99 doge caravan


If it has a 3.3 or 3.8 it is located on the passenger side on the top towards the back.

Sep 22, 2010 | 1999 Dodge Caravan

1 Answer

Where can I buy a water pump of Hyundai Galloper 1999-2000 model Engine - D4BXN or its alternative products that fit the car or model. Please help?


the only information I could find on that engine is that it is apparently a Mitsubishi product, you might try locating a part number on the water pump, that would be very beneficial, then you could google the part number or even take it to your local parts store and have them locate it.

May 28, 2010 | Hyundai Motor 2000 Tiburon

1 Answer

1999 Hyundai Tiburon losing complete power while driving


sounds like the alternator is going out sometimes it works sometimes it doesnt it will blow the battery up if not taken care of

May 03, 2010 | 2003 Hyundai Tiburon

2 Answers

Need the timing marks for 2001 hyundai tiburon


1.5L And 1.6L Engines

a826891.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


4e7384e.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines



1.5L Engines

238c1f1.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L DOHC engines


b1c71ee.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines


c200f83.jpg

Fig. Proper pulley alignment for timing belt installation at TDC-Hyundai 1.5L SOHC engines, 1.6L similar



1.8L (VIN M) And 2.0L (VIN F) Engines

656db91.jpg

Fig. Proper alignment of the timing belt alignment marks for belt removal and installation-Hyundai 1.8L and 2.0L (VIN F) engines



2.0L (VIN P) Engines

7208166.jpg

Fig. Oil pump and crankshaft inner timing belt sprocket alignment marks-Hyundai 2.0L (VIN P) engines


7080ea8.jpg

Fig. Timing belt sprocket alignment mark locations and positioning for belt removal and installation-Hyundai 2.0L (VIN P) engines



3.0L (VIN G)

3b377fb.jpg

Fig. Installation of the timing belt-3.0L (VIN G) engine




7b32092.jpg


Fig. Timing belt sprocket alignment mark positioning for belt removal and installation-Hyundai 3.0L engine


Hope this helped (remember comment and rated this post).

Apr 13, 2010 | 2001 Hyundai Tiburon

1 Answer

How do I change the timing belt on a 2003 Tiburon


2003 Hyundai Tiburon 2.7L MFI DOHC 6cyl

Inspection
Inspect the drive belt for signs of glazing or cracking. A glazed belt will be perfectly smooth from slippage, while a good belt will have a slight texture of fabric visible. Cracks will usually start at the inner edge of the belt and run outward. All worn or damaged drive belts should be replaced immediately.
Removal & Installation
  1. Raise and support the vehicle.
  2. Remove the engine splash shield.
  3. Rotate the drive belt tensioner clockwise to release the drive belt tension.
  4. Remove the drive belt from the alternator.
  5. Slowly release the drive belt tensioner.
  6. Remove the drive belt from the accessory drive pulleys.
To install:
  1. Install the drive belt to the accessory drive pulley.
  2. Rotate the drive belt tensioner clockwise.
  3. Install the drive belt to the alternator.
  4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
  5. Slowly release the drive belt tensioner
  6. Install the engine splash shield.
  7. Lower the vehicle.
b3e0cbe.jpg

Fig. Accessory drive belt routing-3.0L and 3.5L engine


4a6b54d.jpg

Fig. Accessory drive belt routing-2.5L and 2.7L engines


3b0d2d5.jpg

Fig. Accessory drive belt routing-2.4L engines


6470b70.jpg

Fig. Accessory drive belt routing-2.0L engines


6d43bf5.jpg

Fig. Accessory drive belt routing-1.5L engine


508cf9b.jpg

Fig. Accessory drive belt routing-3.0L engine


99b1d12.jpg

Fig. Accessory drive belt routing-2.5L engines


97529b0.jpg

Fig. Accessory drive belt routing-2.4L engines


5cd1383.jpg

Fig. Accessory drive belt routing-1.8L and 2.0L engines


3e72758.jpg

Fig. Accessory drive belt routing-1.5L engine


2aafa70.jpg

Fig. Accessory drive belt routing-2.4L engines


aa6cd2c.jpg

Fig. Accessory drive belt routing-2.0L engines


4081274.jpg

Fig. Accessory drive belt routing-1.5L engine


I hope help you with this (remember rated this help) Good luck.

Sep 15, 2009 | Hyundai Tiburon Cars & Trucks

1 Answer

How do you change a timing belt on a 1998 hyundai tiburon


put engine at TDC. place a jack under the oil pan, remove the engine mount followed by the belts remove the mount bracket, timing cover and the timing tensioner, remove the belt and reinstall make sure its in time by cranking by hand about 3 full turns

Jun 30, 2009 | 1998 Hyundai Tiburon

3 Answers

MY SUNROOF WONT CLOSE


Check the owner's manual. There should be a section showing how to manually close the sunroof. You will use an allen wrench to turn the gears manually, I just don't know exactly what size or where the hole is located. It is typically located right behind the sunroof with a plug covering the hole in the headliner.

Mar 16, 2009 | Hyundai Motor 1999 Tiburon

2 Answers

I need instructions on replacing the timing belt


1. Remove the Alternator Belt.
2. Remove the Water Pump Pulley
3. Remove the Air Conditioner Belt and Power Steering Belt.
4. Remove the Crankshaft Pulley.
5. Remove the timing belt cover
6. Remove the timing belt tensioner pulley.
7. Remove the Timing Belt.
8. (If Replacing) Remove Idler Pulley.
Installation is reverse of removal. Keep a close eye on the timing marks on the cam sprockets to make sure you don't knock anything out of whack.

I would strongly recommend replacing the water pump while you are replacing the timing belt. (The water pump usually comes in the timing belt kit.) Otherwise you are going to have to do this all over again when your water pump goes out. Good Luck.

Nov 10, 2008 | 2004 Hyundai Tiburon

Not finding what you are looking for?
Hyundai Motor 1999 Tiburon Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...