Question about 1995 GMC Sierra C1500

1 Answer

1995 gmc sierra clutch pressure problem

Just blew the clutch in my truck and replaced the hydralic line and slave cylinda. bled the line out but when i pump the pedal there is still no pressure and its making a "gurggling" noise up around the master/firewall. anyone have any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 64 Answers

Could be wrong here but sure sounds like its out of fluid at the "master cylinder" look near the brake master cylinder for a seperate little container for the clutch. bleeding is tricky because it is small and wants to run out of fluid quick. you have to keep adding each time you bleed. Hope I helped. Thanks

Posted on Apr 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have to push clutch all the way to floor to get in gear


I am assuming that you have a hydraulic clutch. You may have a fluid leak in the clutch system. Leaks often develop at either the master cylinder end at your foot, or the slave cylinder end at the gearbox. Once any piston seals have been replaced or master/slave cylinders have been replaced then the system will need to be bled and this should then rectify the issue.

Sep 22, 2013 | 2000 GMC Sierra

1 Answer

Clutch has no pressure behind it


Check your clutch slave cylinder. If this fails you can be unable to engage the clutch at all.

Mar 04, 2013 | 1995 GMC Sierra

2 Answers

Replaced clutch then it seemed like there wasnt enough pressure to release it so i have since replaced the slave cylinder no differance so i took a C clamp and worked it in place of the slave cylinder and...


These and Blazers were notoriously hard to bleed the air out of the system. I actually had to make up a clutch reservoir cap with a nipple on the top so I could hook it up to a vacuum pump. With the system full, try to attach a vacuum pump (hand operated one works fine) over top of the reservoir, or if need be to the feed line to the master cylinder. Apply vacuum until you can see fluid, soon you should see bubbles in the line. Maintain constant vacuum until all air is gone the system should be fully functional after that.

Mar 19, 2011 | 1995 GMC Sierra C1500

1 Answer

I cant get pressure to my clutch pedal in my 1995 saturn sc2. i changed out the slave cylinder and the clutch. I tried bleeding the slave cylinder, and still no pressure, why?


You cannot bleed these clutch hydraulics. They are meant to be a pre-bled sealed unit that you buy. You should never replace just the slave or the master. Buy them both and replace them as one unit which is already bled from the factory. Otherwise you will experience what you are describing.

Make sure you install the slave cylinder (into the transmission hole) first and then the master cylinder (pedal side) next and do not hook up the pedal until everything is installed.

If you take the slave out with the pedal attached it will extend the rod and ruin the hydraulics rendering them useless.

Feb 20, 2010 | 1995 Saturn Sc

1 Answer

HI, I HAVE A 1995 PROBE 2.0 16V,& I JUST RECENTLY REPLACED THE CLUTCH & PRESSURE PLATE.JUST YESTERDAY WHEN I WANTED TO DRIVE IT,I COULD NOT SEEM TO SELECT ANY GEARS TO PULL AWAY. WHEN I PRESSED...


If hydralic, it sound like you have air in the hydralic line. You need to bleed it off at the slave cylinder (gearbox end of the line)

If cable type, then you may need to reset the ratchet on the clutch pedal.

Dec 07, 2009 | 1994 Ford Probe

1 Answer

We have bled the lines on a 1994 gmc sierra and are getting no tension in the clutch what do we do?


From your comments, your clutch master is no longer
working. Check your clutch master, and replace all the
worn out parts. You can buy all of these in one pack,
specify Clutch Master Repair Kit for 1989 GMC Sierra.

Oct 05, 2009 | 1989 GMC Sierra

1 Answer

My 94 gmc sierra 6.5 td keeps blowing the clutch master cylrnder


It needs a clutch pressure plate force is to great do lining & reface flywheel then good to go for a longggggg time

Sep 01, 2009 | GMC Sierra 2500 Cars & Trucks

1 Answer

Clutch wont engage


With the hydraulic systems, there is no adjustment. So what pedal travel you have is likely normal for that vehicle.

May 30, 2009 | 1994 GMC Sierra

3 Answers

1995 GMC Sierra Clutch


either the clutch master cylinder went bad or the clutch slave went bad. look for dripping fluid

Apr 19, 2009 | 1995 GMC Sierra

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

643 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...