Question about 1983 Ford Mustang Hatchback

1 Answer

Need to know what size bolts bolt together the bellhousing.

Its a c4 tranny on a 83 mustang has the v8 302. I lost the bolts for it. if someone could give me which size bolt to use and where to get them it would be greatly appriciated. Thanks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is a 7/16 ths size bolt about two and a half inches long. i just pulled mine saturday

Posted on Apr 28, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's what size bolt do I need for a 89 Diahau charade bellhousing?


We have no reference material to look that up

Remove one bolt ,measure its diameter in inches
& divide by .0395 to convert to metric bolt size

Oct 03, 2012 | 1989 Daihatsu Charade

1 Answer

Need to know bolt size transmission 1991 s10


The heads are actually 9/16, the bell housing bolts are standard, not metric. All the other bolts are metric.

May 04, 2010 | 1991 Chevrolet S-10 Blazer

1 Answer

I have a 96 F150 and I need to replace my clutch. My tranny code is M which should be the M5OD-R2 (correct?) I'm not sure if my clutch plate is a 10in or an 11 in.


You will take old parts in so no need to know ahead of time what size.
Basically clutch sandwiched between engine and transmission.
Transmission usually easiest to remove.
Drive shaft first.
If starter on tranny, then remove batter cable.
Sometimes ground strap.
Speedo cable, backup lights cable, etc.
Small bolts on bottom plate.
Support transmission and engine separately.
Some trucks have removable tunnel cover, which makes it much easier.
6 large bolts between engine and bellhouseing.
Lower transmission and back of engine only enough so you can slde transmission back.
Then slide it back out of engine and clutch.
Usually about 6 inches or less.
Then get it out of the way.
About 10 bolts on pressure plate.
Do diagonally and in steps.
Friction disk sandwiched between pressure plate and flywheel, will just fall out.
Throw out bearing is on fork back in bellhousing of tranny.

Check pilot busing in center of flywheel.
Supports tranny shaft, so must be good, well greased, no rust, no binding.

Install is reverse of procedure, except you need to hold the friction disk in center, while tightening pressure plate. They sell a cheap plastice stub shaft substitute that you can buy or improvise. But important, because you will be trying to get that heavy transmission with long imput shaft back through the fiction disk hub and into pilot busing. Alignment is critical. Sometimes turing engine helps.
Extra long bolts temporarity, also helps. A little rocking and shoving. Constantly compare gap on bottom and top of bellhousing to engine.
When it slides in, youwll know, and an bolt it back up. But don't try to just force it.
Also don't over tighern pressure plate bolts, because they are small. Use torque wrench.

Feb 18, 2010 | 1996 Ford F150 Regular Cab

1 Answer

How to pull out tranny and fix TO bearing on a 97 mustang v6. 5 speed thanks alex


start by removing the the shifter lever and boot, next remove the drive shaft,then remove clutch cable or hydraulic line for throw out fork,it may be neccessary to remove y-pipe and some of the exhaust using a transmission or floor jack support transmission and remove crossmember, remove bellhousing bolts and transmission should now be free to remove.

Jul 18, 2009 | 1999 Ford Mustang Cobra

1 Answer

I don't know the size of the original Transmition,that came in my Cutlass supreme 1987.,i jst put a 350 rocket in the car and need a tranny,the bolt patterns,weather or not the tranny has...


If I remember correctly that engine used a 350 trans. You will need to check bolt patterns on bellhousing to make sure there are no differences in bolt pattern but I believe they are the same. With a little work you could also stuff a 400 or a 700r4 (with overdrive) unit in there but you would need some mods to do that. Don't forget that tailshaft lengths vary depending upon where the unit came from so you may need to either change tailshaft or have a driveshaft made to fit.

Apr 03, 2009 | 1987 Oldsmobile Cutlass Supreme

2 Answers

Replace the starter on a 95sn mustang convertable


There are two bolts holding the factory starter/reducer onto the 5.0 block. The bottom bolt should be easily accessible from underneath while up on ramps/stands but the top bolt must be reached by feeding several long extensions through the front of the motor (by the pulleys) onto the top bolt. If you look down the passenger side by the header you will see the top bolt. You will have to take the intake piping off as well.

Mar 19, 2009 | 1995 Ford Mustang

1 Answer

What bolt to use for the bellhouseing on tranny?


most bolts for your bell housing are two inchs in lingth and are mittrck or mm. but what tipe of moter do you have i need the size and what tipe of tran's, do you have''''is it a v8''' or a 4-banger or a 6--''''' or a v--6'' my name is james'' you can e-mail me back at '' jay_win2002@yahoo.com'''

Jan 30, 2009 | 1983 Ford Mustang Hatchback

2 Answers

Installing


you have two bolts on your starter take the two bolts out and take the wire off the strater

Jun 11, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...