Question about 1984 Toyota 4Runner

1 Answer

1988 4Runner RH Dash Removal

1988 Toyota 4 Runner How do I remove the right side of the dashboard? It seams to be free in the front and a mysterious connection in the back, near the windscreen. The solution eludes me.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I know this post is a bit older, but... You have to remove the right most vent. --To do this slide a thin, flat screwdriver on the tops and bottoms of the vent to press the spring clips. Behind it is one last bolt (10mm) that holds it on.
Hope it helps sammy

Posted on Jun 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

1 Answer

How do i remove instrument panel cluster on 98 towncar


Removal
  1. Remove the steering column
  1. Remove the passenger side air bag module
  1. Position the speed control servo aside.
    1. Remove the nuts.
    1. Position the speed control servo aside.
    gr2792a.gif
  1. Disconnect the LH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the LH bulkhead connector.
    gr2793a.gif
  1. Unclip the LH bulkhead connector from the dash panel.
    gr2794a.gif
  1. Remove the windshield washer reservoir
  1. Disconnect the blower motor electrical connector.
    gr2795a.gif
  1. Disconnect the A/C pressure cut-off switch electrical connector.
    gr2796a.gif
  1. Disconnect the in-line wiring harness connector.
    gr2797a.gif
  1. Disconnect the electronic automatic temperature control (EATC) variable blower motor controller electrical connector.
    gr2798a.gif.
  1. Raise and support the vehicl
  1. Remove the RH front wheel and tire assembly.
    1. Remove the lug nuts.
    1. Remove the RH front wheel and tire assembly.
    gr2845a.gif
  1. Remove the front fender splash shield bolts.
    gr2800a.gif
  1. Position the front fender splash shield away from the dash panel.
    gr2801a.gif
  1. Unclip the wiring harness from the evaporator case.
    gr2802a.gif
  1. Unclip the wiring harness from the dash panel.
    gr2803a.gif
  1. Lower the vehicle.
  1. Lower the RH instrument panel lower insulator.
    1. Remove the pushpins.
    1. Lower the RH instrument panel lower insulator.
    gr2805b.gif
  1. Remove the RH instrument panel lower insulator.
    1. Disconnect the power point electrical connector.
    1. Remove the courtesy lamp from the lamp socket.
    1. Remove the RH instrument panel lower insulator.
    gr2806a.gif
  1. Unseat the wiring grommet and feed the wiring harness through the dash panel.
    gr2804a.gif
  1. Remove the LH and RH cowl side trim panels.
    gr2807a.gif
  1. Remove the LH and RH windshield side garnish moldings.
    gr2808a.gif
  1. Disconnect the electronic crash sensor (ECS) module electrical connector.
    1. Disconnect the locking clip.
    1. Disconnect the electrical connector.
    dr0308a.gif
  1. Disconnect the antenna cable in-line connector.
    gr2809a.gif
  1. Remove the RH ground bolts.
    gr2810a.gif
  1. Disconnect the EATC hose from the evaporator housing.
    gr2811a.gif
  1. Disconnect the RH bulkhead connector.
    1. Loosen the bolt.
    1. Disconnect the RH bulkhead connector.
    gr2812a.gif
  1. Position the LH and RH door weatherstrip seals away from the instrument panel.
    gr2813a.gif
  1. Remove the tunnel brace trim cover.
    gr2814a.gif
  1. Disconnect the climate control head vacuum harness connector.
    gr2815a.gif
  1. Remove the instrument panel tunnel brace.
    1. Remove the nuts.
    1. Remove the instrument panel tunnel brace.
    gr2816b.gif
  1. Remove the LH ground bolts.
    gr2817a.gif
  1. Disconnect the LH wiring harness connectors.
    gr2818a.gif
  1. Disconnect the parking brake switch electrical connector.
    gr2819a.gif
  1. Remove the instrument panel defroster opening grille.
    1. Unclip the instrument panel defroster opening grille from the instrument panel.
    1. Disconnect the electrical connectors.
    1. Remove the instrument panel defroster opening grille.
    gr2820a.gif
  1. Remove the three instrument panel cowl top screws.
    gr2821a.gif
  1. Remove the RH instrument panel cowl side nut.
    gr2822a.gif
  1. Remove the upper LH instrument panel cowl side nut.
    gr2823a.gif
  1. Remove the lower LH instrument panel cowl side bolt.
    gr2824a.gif
  1. NOTE: Removing the instrument panel from the vehicle requires two technicians.
    Remove the instrument panel from the vehicle.
    gr2879a.gif

Mar 07, 2011 | 1998 Lincoln Town Car

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

Where is the location of turn signal flasher? I have looked under the dash to the left of the steering column. Am I close?


1993 Toyota Truck 4 Runner 4WD 3.0L FI 6cyl the Flasher is located: Front seating area, driver side, under dash, mounted driver side of steering column

Hope helps.

Oct 09, 2010 | 1993 Toyota 4Runner

1 Answer

Starter removal on a 1990 toyota 4 runner. Where


it is not fun w/o lift look behind passenger wheel you will need to raise front end remove wheel ,remove skid pan,and of course battery ends if 4wd I highly reccomend a lift good luck and please rate this

May 05, 2010 | 1990 Toyota 4Runner

2 Answers

Need to pull the panel off driver side door of 2004 ford f150


SECTION 501-01: Body System — Interior 2004 F-150 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/17/2004 Front Door Trim Panel adobe.gif Printable View (229 KB) Removal and Installation
NOTE: LH side is shown. RH side is similar.
  1. Remove the front door speaker. Refer to Section 415-00.
  1. If equipped, remove the window regulator handle.
    1. Separate the handle cover from the handle.
    1. Remove the screw.
    1. Remove the window regulator handle.
    1. Remove the spacer.
    r12386a.gif
  1. Remove the parts in the order indicated in the following table.

    a0005479.gif
    Item Part Number Description 1 224A60 Cover plate 2 N602704-S301 Screws (2 req'd) 3 14B132A (RH) / 14B133B (LH) Window control switch 4 14630 (RH) / 14631 (LH) Window control switch electrical connectors 5 W505424-S301 Bolt 6 W701930-S424 Bolts (2 req'd) 7 19A034 Water shield 8 W709132-S300 (High series trim) / W709133-S300 (Low series trim) Speaker standoff (2 req'd) 9 219A65 (LH)/ 219A64 (RH) Front door handle
    Removal Note 10 23942 (RH) / 23943 (LH) Front door trim panel
    Removal Note
  1. To install, reverse the removal procedure.
Item 9: Front Door Handle Removal Note
  1. Guide the door handle through the opening in the trim panel.
Item 10: Front Door Trim Panel Removal Note
ani_caut.gif CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.
  1. Lift upward and remove the front door trim panel.

2010&c18=modelyear&c20=n717901&c35=wsm%2cfront%20door%20trim%20panel%2cs42%2c501-01%2cremoval%20and%20installation&pid=wsm%2ctitle%20page%202004%20f-150%2cs42&pidt=1&oid=functiononclick%28%29%7bdosearch%28%29%3b%7d&oidt=2&ot=img&oi=27&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=491&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 2004 Ford F150

2 Answers

90 4 runner v-6 crank shat pulley bolt removal . Right or left to remove


Not quite sure, but rule of thumb, which ever way it turns while running, that's the way it comes off. This prevents it from ever coming loose.

May 02, 2009 | Toyota 4Runner Cars & Trucks

1 Answer

Need help with dash removal.


  1. Remove the A-pillar and cowl side Trim Panels
  2. Remove the front floor console.
  3. Depower the supplemental restraint system (SRS).
  4. Remove the instrument panel side finish panels.
  5. Remove the 2 steering column opening cover screws.
  6. Remove the steering column opening cover.
  7. Remove the 3 lower steering column cover screws.
  8. Remove the lower steering column cover.
  9. Disconnect the steering column electrical connectors.
  10. Disconnect the RH side bulkhead electrical connector.
  11. Disconnect the RH side body harness electrical connector.
  12. Remove the 2 parking brake release handle screws.
  13. Disconnect the LH side instrument panel electrical connectors.
  14. CAUTION: To avoid damage to the clockspring, do not allow the steering column shaft to rotate while the intermediate shaft is disconnected.
  15. Remove the pinch bolt..
  16. Disconnect the adjustable pedal electrical connector.
  17. Disconnect the brake light switch electrical connector.
  18. Remove the 2 LH instrument panel center brace bolts..
  19. Remove the 2 LH instrument panel center brace nuts.
  20. Remove the LH instrument panel center brace.
  21. Disconnect the transmission range selector lever cable.
  22. Disconnect the RH side bulkhead electrical connector.
  23. Disconnect the LH side body harness electrical connector.
  24. Remove the 3 ground strap bolts.
  25. Disconnect the inertia switch electrical connector.
  26. Disconnect the RH side instrument panel electrical connectors.
  27. Remove the 2 RH instrument panel center brace bolts.
  28. Disconnect the vacuum connector.
  29. Remove the 2 RH instrument panel center brace nuts.
  30. Remove the RH instrument panel center brace.
  31. Remove the cowl panel grille
  32. Remove the instrument panel bolt located under the cowl panel grille
  33. Remove the instrument panel defroster grille.
  34. CAUTION: To avoid damage to the sunload sensor and electrical connector, remove the grille just enough to disconnect the connector.
  35. Disconnect the sunload sensor electrical connector.
  36. Remove the 2 instrument panel top cowl bolts.
  37. Disconnect the antenna lead-in cable.
  38. Disconnect the RCM electrical connector.
  39. Disconnect the center ground strap bolt.
  40. CAUTION:To avoid damage to the instrument panel, an assistant is required to support the panel before carrying out this step.
      • Before removing the instrument panel make sure all electrical connector wiring is free and not hindered.
  41. Remove the 4 instrument panel bolts.
  42. Remove the instrument panel.
  43. To install, reverse the removal procedure.

Feb 11, 2009 | 2005 Ford Explorer

1 Answer

Where do the plug wires go to on my 1998 toyota 4 runner


contact your local Autozone parts store and they can give you a print out for free.

Nov 22, 2008 | 1998 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

593 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...