Question about 1996 Dodge Ram 1500 Club Cab

1 Answer

Replacing front wheel ujoint on 2001 ram dodge 1500

Ujoint has lost caps ive pulled rotor off ive dropped sway bar it has auto locking hubs i removed center nut i dont kno what to do next please help,my wife has cancer in hospital im disabled cant afford someone else to repair if u can send me diagram i would bless u an your family please in the name of god help i cant afford haynes mannual godbless you my name is Tracy if you have any other web sites that could help that would be great

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

HUB BEARING AND AXLE SHAFT REMOVAL

  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake components from the axle, Refer toBrakes.
  4. Remove the cotter pin and axle hub nut.
  5. Remove the hub to knuckle bolts Hub and Knuckle Remove the hub bearing from the steering knuckle and axle shaft
  6. Remove the brake dust shield.
  7. Remove the axle shaft from the housing. Avoid damaging the axle shaft oil seal.
INSTALLATION
  1. Clean the axle shaft and apply a thin film of Mopar Wheel Bearing Grease to the shaft splines, seal contact surface, hub bore. Install the axle shaft into the housing and differential side gears. Avoid damaging the axle shaft oil seals in the differential.
  2. Install dust shield and hub bearing on knuckle.
  3. Install the hub bearing to knuckle bolts and tighten to 170 N·m (125 ft. lbs.) torque.
  4. Install the axle washer and nut, tighten nut to 237 N·m (175 ft. lbs.) torque. Align nut to next cotter pin hole and install new cotter pin.
  5. Install the brake components, Refer toBrakes.
  6. Install the wheel and tire assembly.
  7. Remove support and lower the vehicle. replacing front wheel ujoint on 2001 ram dodge 150 - 8014d67b.gif

Posted on Feb 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the hub assembly from the front wheel of my 2001 dodge ram RWD?


  • Jack up your Dodge Ram. Block the wheels to keep it from rolling as you work. Get started by removing the first tire and wheel assembly. Remove the hub extension and the brake caliper as well as the caliper adapter.
  • Remove the grease cap, cotter pin, nut lock, nut, washer and outer wheel bearing. Now, pull the old rotor off of the spindle. Clean the area with a damp cloth to remove any debris. Pack the wheel bearings with grease.
  • Install the new rotor and hub onto the spindle. Replace the outer wheel bearing, washer, and then the retaining nut. Torque the nut to 30 to 40 ft. lbs. while rotating the hub and rotor. Then tighten the nut and install the nut lock and a new cotter pin.
  • Clean the grease cap and then coat it with new wheel bearing grease and replace the cap. Put the caliper adapter back into place and then tighten the two mounting bolts with a torque wrench. Install the wheel and tire assembly.
  • Repeat this process for each additional rotor and then lower the vehicle. Tighten the lug nuts and test drive your Dodge Ram to make sure that the installation was successful.


  • If I've helped, please vote!

    Dec 10, 2010 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


    Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

    e9801b.gif


    Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
    (Part of 3B458) 15 - Plastic Thrust Washer
    (Part of 3B458) 16 - Splined Thrust Washer
    (Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
    (35-53 Lb-In) Removal
    1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


      de0460a.gif



      de0285a.gif

    1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


      f4658c.gif

    1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


      f4659d.gif

    Installation
    1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

      Follow removal procedure in reverse order.
    1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

    Oct 04, 2010 | 1997 Ford F250 SuperCab

    1 Answer

    On my 2001 Dodge Ram 1500 5.2 2WD, I just found


    This is a very simple job to do. Raise the front of truck off the ground,block the rear tires. Using pliers and a hammer,remove the grease cap from hub. Remove the cotter key and nut from axle,pull out slowly and remove outer bearing. then remove hub from axle. To remove inner bearing ,prop hub on a board and use a large punch to drive out bearing and seal. Clean out inside the hub and install new bearing and seal. Replace all parts in the reverse as you took them off. Hope this will help you.

    May 14, 2010 | 2001 Dodge Ram 1500 Truck 2WD

    1 Answer

    Front rotors and pads


    Those rotors are bolted from the inside of the wheel bearing hub. You have to remove the caliper and mounting bracket,then remove the wheel bearing outer and slide the hub assembly off.Unbolt the rotor.
    Your local library should have a shop manual on it.

    Nov 16, 2009 | 2004 Dodge Ram 1500

    2 Answers

    2001 ram 2500 how to remove the wheel hub assembly


    Remove tire. Remove caliper and caliper holder. Remove rotor. Using a 36 MM socket remove center nut and slide hub off spindle. If hub does not come off freely use wheel puller to remove hub.Loosen front wheel lug nuts. Jack up and support front of truck with jack stands ( put them in the middle so both you can get to both sides of the truck). Remove tire, Remove caliper and caliper holder. romove rotor ( I had to use a 2x4 wedged between rotor and lower controll arm rubber stoper. then started truck and turned the wheel right or left to pop rotor free). remove 3 bolts that hold hub to knuckle. on the next step I used a steel pipe about 1 1/2 foot i think about 2 inches in diamater. wedge it between lower controll arm rubber stoper. then start truck turn the wheel left or right to let power steering pump do the work. It poped it off easy for me both sides in less than 1 hour. put alot of anti seize on the new hubs and bolts in case you have to replace them again. use a torque wrench to tighten all bolts. Great time to replace brakes as long as you are in the area. hope this helps.

    Oct 11, 2009 | 2001 Dodge Ram 2500 Truck

    1 Answer

    I just tried to replace the front rotors on my 1996 nissian pathfinder, but couldn't figure out how to remove the wheel bearing (or is it the hub?). What do I have to do get the rotor off?


    - disconnect ABS sensor and move away to protect from damage
    - remove brake caliper assy.
    - remove hub cap
    - remove snap ring w/tool
    - remove lock washer
    - remove wheel bearing lock nut (tool J36001)
    - pull off wheel hub & wheel bearing (do not drop it!)
    - rotor is attached to hub.

    Apr 28, 2009 | 1996 Nissan Pathfinder

    1 Answer

    4 wheel drive engages but hubs are not locking in


    chances are that your one of your auto locks have when out on you you can replace them with the manual locking type if you dont mind getting out and locking the hubs in. and a plus to manual locks is that they are much much stronger

    Apr 20, 2009 | 1998 Dodge Ram 1500 4WD

    2 Answers

    Clicking noise in front end 2001 dodge ram 4x4


    the ansew i found is replacing the seal around the joint and from both end removing it and cleaning it out i had rocks in mine from going threw water and mud ita a all day deal but a twenty doller fix axle shaft oil seal is all i had to replace

    Apr 05, 2009 | 1997 Dodge Ram 1500 Club Cab

    2 Answers

    Front hub bearing removal 2002 dodge ram 1500 4WD 4.7L V8


    i just did a 2002 2500 4x4 with a dana straight axle and had no problem getting on the bolts with a 9/16 12 point socket on a 6 inch extension. If you do not use an extension the head of the ratchet will hit the yoke of the axle shaft.

    Dec 07, 2008 | 1998 Dodge Ram 1500 4WD

    Not finding what you are looking for?
    Cars & Trucks Logo

    1,231 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    63577 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21981 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...