Question about 1999 Isuzu Trooper

3 Answers

Changed oil and fuel filters on 4jx1, will not start but cranks

What could be the problem pls asisst

Posted by on

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

You must use 5/30 fully synth oil and i guess if you did that and still wont go its going to be air so pump away a bit longer on the primer .Should be some pressure there when its ready to go .

Posted on Jul 07, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 80 Answers

As simon says, oil type is 100% critical, 5w30 fully synthetic only. These engines require oil pressure to be up to fire up. They also can have a lot of air get in when you change the fuel filter. Bleed the filter (10mm nut on side, open it a couple of turns, pump the primer on top till diesel squirts out then do up nut, tight ish, pump a bit more till the primer is hard.) and crank for 10 secs. If no joy, repeat priming. Did you change just one or both oil filters? If all this comes to no avail, drain the oil, and change the second (smaller) filter. This is the one that filters the oil to the injectors, and if the flow is restricted, will slow or stop the starting.

Posted on Jul 12, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I used repsol 5w30 fully synthetic oil and my oil pressure warning light keeps on blinking.

Posted on Sep 30, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a 2002 Holden jackaroo 3 ltd and it will not start it just winds over wat could it be


Holden Jackaroo 2001 3.0 TDI 4JX1 Problems - YouTube

? 8:14
https://www.youtube.com/watch?v=xLySKue4HzM
Feb 22, 2013 - Uploaded by sandgroper111
Holden Jackaroo 2001 3.0 TDI 4JX1 Problems .... Hi there, currently own a 3.0 2002 lwb trooper 34K miles ...Missing: ltd

4jx1 cranks over but will not start - Jackaroo Technical ...

forum.australia4wd.com > ... > Jackaroo Technical

Nov 3, 2014 - 10 posts - ‎5 authors
Page 1 of 2 - 4jx1 cranks over but will not start - posted in Jackaroo Technical: Hi all, this is my first post so ... Holden at Pennant Hills Syd diagnosed a cracked cylindar head. ... I took the car into an auto elec at Alexandria who diagnosed No 3 injector faulty. ... I have a similar issue with my 2002 4JX1. 4jx1 rough idle, wont rev above 2500 rpm and wont ...
8 posts
Apr 16, 2013
Oil Rail Pressure Sensor Valve Rebuilding for 4JX1 ...
10 posts
Apr 22, 2012
Diesel Jackaroo hard to start - Jackaroo Technical ...
6 posts
Oct 9, 2011
More results from forum.australia4wd.com
Missing: ltd

Nov 17, 2015 | Holden Cars & Trucks

1 Answer

4jx1 engine no oil suction after we change ingine oil 15w 30


Not sure what 4jx1 means. What vehicle are you working on? If engine was fine until you changed oil, and you did nothing but change oil, you have a real mystery. Did you also change oil filter? Are you absolutely sure the new filter is the correct one for your engine AND that it's not some cheap walmart filter which could be the whole problem? I have seen a few filters which were made wrong from the factory.

Dec 10, 2014 | Cars & Trucks

1 Answer

Isuzu Big Horn (Trooper) 4JX1 engine.... Vehicle would start and only idle. Some time later it failed to start.. Where do we look for the fault Checked cam sensor and crank. Still need to check ORPS. How...


Sends a signal related to the rail pressure as a voltage to the ECM. 3 wire connector :
  • Red : 5V (Feeds from ECM connector J1-4) Shared with MAP sensor, EGR pressure sensor and accellerator position sensor.(compare values from these sensors and ECM connector)
  • Black : Ground (Feeds from ECM J2-22) Shared with the same sensors mentioned above
  • White : Signal feeds to ECM connector J2-22
Low pressure will set P1194 error code. Oil rail pressure should be more than 3MPa when cranking

Also check Engine coolant temp sensor and wiring. Engine coolant to manifold temp should not differ by more than 5 deg C either way after 8 hours of no operation. I have found the same symptom on these diesels with fuel supply problems. Operate the priming pump (on top of the fuel filter) until it becomes diffycult to push down before starting or checking anything else.

Oct 02, 2010 | 1998 Isuzu Trooper

2 Answers

Isuzu tropper 4jx1


You have no injection pump ,each injector does that job .
You have a faulty rail oil pressure sensor I think ,read my tips to test this sensor .

Feb 06, 2010 | 1998 Isuzu Trooper

2 Answers

I cant find the location of diagnostic socket of Isuzu 4jx1


The ODB socket is just under the plastic trim that goes over the gearlever cover by your right foot , no tools needed to get it out .
The 4JX1 is a HUEI type engine so the diesel is not under high pressure until injected .
To prove if the fuel is starved put fuel in a can and pipe it into the hand primer pump direct .
Most likely cause is the Rail Oil Presure Sensor as this controls the amount of fuel injected via the ECU .

Jun 18, 2009 | 1999 Isuzu Trooper

1 Answer

1999 trooper 4JX1 fuel black


engine oil leaking past injector O rings and going into fuel return hose back to tank contaminates tank. if recall done are O rings ok? can put clear plastic tube on return fitting in rear of head to see if black (contaminated with oil) or air leaks, from cold start, it isnt high pressure
it could be from before or now?

Oct 30, 2008 | 1999 Isuzu Trooper

3 Answers

4JX1 engine cut off while test drive after oiland filter change and not starting


That pop noise is ok just the flap in the throttle body coming open when the car stops .
The engine may have stopped because its low on oil so the oil pump for the injectors wont work - takes about 7 u.s. quarts of 5/30 fully synthetic oil at service time to run right.
It can also stop if the pressure sensor in the injector rail packs up or the oil pick up pipe for the injector system falls off due to cracking the mount .

Oct 28, 2008 | 1999 Isuzu Trooper

4 Answers

Isuzu 4JX1 EngineWont Start after replacing new injector


my isuzu bighorn will not start after changing valve seals and head gasket and after setting timing it still will not start. do you have a solution.

Aug 09, 2008 | 1999 Isuzu Trooper

Not finding what you are looking for?
1999 Isuzu Trooper Logo

1,720 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...