Question about 1992 Honda Accord

1 Answer

Sticky clutch 91 accord lx clutch sticks to floor or is slow to release. I replaced master cylnder, slave has small leak but never goes through any fluid what else could it be?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Slave cyl is sepreate from master cyl you have air in the clutch hydraulic system replace slave and inspect clutch master for leaks on drivers floor board area pull carpet back and make sure to bleed system properly!!!!!!!

Posted on Feb 26, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a honda accord coupe 94 the clutch stops workin after i start the car i ihe car doest accelerates


If you mean you step on the clutch, put transmission in gear and release clutch with no engagement (pedal returns to top position) there is a good chance your clutch disc or pressure plate, or both are worn out and need replacing.
If your clutch pedal is going to the floor and not returning there could be a leak in the system, a bad clutch master cylinder or a bad slave cylinder on the transmission. Check the fluid level in the clutch master cylinder. If it is low or empty you have a leak or component failure. Visually inspect clutch master, line, slave cylinder for fluid leaks. replace as needed. If hydraulics are o.k., suspect clutch disc/pressure plate.

May 09, 2014 | 1994 Honda Accord

2 Answers

My clutch is sticking to the floor, but there is plenty of fluid and there does not appear to be a leak


you may need the clutch replaced if the clutch slave cylinder and master is working.

Jun 22, 2011 | 1988 Mazda B2200

1 Answer

My clutch petal on my 91 honda accord has no resistance and i know that it is due to the fact that i was in hospital and did not keep it full. i drove it home and it was fine but, for four day after that i...


You should not need to be filling the clutch master frequently. The system is "closed" and should stay full indefinitely. If frequent filling is necessary, there is a leak either in the master, line or slave. There should be a bleed valve on the slave unit mounted on the bellhousing. You can usually restore operation temporarily by bleeding it from there as you would a brake. (hold pedal down and open bleeder, let air out and close bleeder, release pedal and repeat 'till only fluid comes out) But you need to take a close look and find/replace what's leaking.

Feb 23, 2011 | 1991 Honda Accord

1 Answer

Clutch problems .I have to pump my clutch for 15 minutes to get it to shift into gear when car is running. What is the problem


this is due to air in the clutch system, or a low fluid level. bleed some new clutch fluid through. It may be caused by a leaking seal, so check for leaks at the clutch master cylnder and slave cylnder. the master cylnder seal sometimes leaks down the firewall inside the car. Replacement cylnders ar an easier option than replacing just the seals

Apr 20, 2010 | 1996 Nissan Maxima

2 Answers

The clutch is stuck to the floor bord and i cant shift


you may have a faulty clutch master cylinder or faulty clutch slave cylinder- leaking clutch fluid. most of the time both are replaced at the same time which should be recomended by your mechanic, the bolts to the master cylinder are very hard to get to and require the right tool.
you should be able to move car forward by selecting 1st then cranking engine till it starts, gear changes while driving are hard but not impossible. i recommend a tow truck to a local repairer.

Dec 22, 2009 | 1995 Isuzu Rodeo

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

1996 honda accord clutch goes all the way to the floor


check the slave and clutch master cylinder for leakage. look under the dash , at the clutch master) push rod attached to the clutch pedal) . try to see if there are any leaks around it. if so have it replaced and have the system bled to remove all fluid and air stuck in the system.

Apr 04, 2009 | 1996 Honda Accord

2 Answers

Clutch has no resistance, stays near floor after applying pressur


You could refill but, i would replace the clutch master cylinder and slave cylinder as well. these two parts are failing.

Mar 06, 2009 | 1991 Honda Accord

1 Answer

Clutch sticks to floor or is slow to release?


could be a couple of things check release bearing is not binding on output shaft or the arm which holds the release bearing is not bent or worn where it pivots also check where the arm pivots point is not worn out if all checks out replace the clutch pressure plate,clutch discs,throw out bearing and pilot bearing,one more thing is a clutch disc has some springs mounted to it to absorb some of the pressure when engaging the clutch and i have seen these springs come off and get in between the clutch assembly but usually when this happens you can feel and hear some grinding metal noise.but to check all the above the transmission will have to be removed.

Feb 26, 2009 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...