Question about 1990 Daihatsu Rocky

1 Answer

I need a daigram on how to instal the fuel injection system

Can anybody tell me were can i find a diagram on how to install the hoses on a fuel injection system for a daihatsu rocky 1990 1.6cc

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a wiring diagram for a 2015 Kia Soul


Wiring diagrams are broken down into systems, like fuel injection, AC heater and so on, so what system are you asking for?

Jul 12, 2016 | 2015 Kia Soul

1 Answer

Installing rebuilt pump don't know were to start never worked diesel before know anything about injector pumps.


When installing a new fuel pump on a ud truck 1400 1994 desiel.......

Resolved Question:

When installing a new fuel pump on a ud truck 1400 1994 desiel....... how do you set the timing, i can't find a mark on the pump. Submitted: 3 years ago. Category: Medium and Heavy Trucks Share this conversation Mechanic's answer sascityks.64x64.jpg"> Tkman55 , Mechanic 125 Satisfied Customers Expert: tkman55 replied 3 years ago. Let me see if I can help you with your problem. Please don't rate me until all your questions are answered, that way you will not have to pay twice. Always use "Reply To Expert" link. Thanks.
If you are new to the site this is how it works:
1. We will go back and forth as needed until you get the help you need, there will be no extra cost for replying.
2. I will give you the best possible information without actually being physically present with you.
3. Remember to leave a positive rating after we are finished.
INJECTION PUMP

Removal
  • 1. Disconnect negative battery cable. Remove injection tubes from nozzles and plug nozzles. Remove fuel cut solenoid wire and accelerator wire. Disconnect fuel inlet hose, overflow hose and fuel return hose. Remove injection pump drive gear cover. Mark injection pump shaft and gear for proper alignment during reassembly.
  • 2. Loosen injection pump drive gear nut and remove gear. Remove injection pump bolts and nuts. Remove injection pump with injection tubes attached.

Disassembly & Inspection
For disassembly, inspection and reassembly procedures for injection pump or injectors, see DISASSEMBLY & REASSEMBLY in Fuel System article.

Installation
  • 1. Turn engine until No. 1 piston is at TDC on compression stroke. Install injection pump assembly. Install injection pump gear so that flange is aligned with mark on front cover. See Error! Hyperlink reference not valid. . Install gear nut and tighten to 43-51 Ft. Lbs. (59-69 N.m). Tighten injection pump fixing bolts. See INJECTION PUMP MOUNTING TORQUE table. Tighten injection pump to mounting bracket bolts.
  • 2. Install injection pump gear cover with new gasket. Connect fuel inlet hose, overflow hose and fuel return hose. Connect fuel cut solenoid wire and accelerator wire. Connect injection tubes to nozzles. Tighten tube flare nuts to 14-18 Ft. Lbs. (20-25 N.m).
  • 3. Connect negative battery terminal.


Read more: http://www.justanswer.com/medium-and-heavy-truck/746q8-when-installing-new-fuel-pump-ud-truck-1400-1994-desiel.html#ixzz3nAToQQfC

Sep 29, 2015 | Cars & Trucks

1 Answer

2.8 crd injection pump


alldata.com, log in and read that yet?
did you look at this near FSM?
the 21 steps, read them yet?. did you make it to step 21,?
quote
  1. Disconnect negative battery cable.
  2. Remove engine cover and bracket.
  3. Evacuate A/C system.
  4. Remove accessory drive belt.
  5. Remove cooling fan and fan shroud.
  6. Remove charge air cooler outlet hose to intake manifold.
  7. Remove fan support assembly.
  8. Remove timing belt outer cover.
  9. Using special tool VM.1055, remove high pressure injection pump sprocket retaining nut.
  10. Install feet from VM.1067 in injection pump sprocket as shown.
  11. Install inner flange of special tool VM.1067 on injection pump sprocket as shown. Secure flange to feet in injection pump sprocket with Allen bolts supplied with tool.
  12. Screw the high pressure injection pump sprocket holding plate assembly into flange of VM.1067. Using left hand threaded bolt supplied, secure holding pl
  13. Before servicing the vehicle, refer to the Precautions section. CAUTION High pressure lines deliver diesel fuel under extreme pressure from the injection pump to the fuel injectors. This may be as high as 23,200 psi.(1600 bar). Use extreme caution when inspecting for high pressure fuel leaks. Fuel under this amount of pressure can penetrate skin causing personal injury or death. Inspect for high pressure fuel leaks with a sheet of cardboard. Wear safety goggles and adequate protective clothing when servicing fuel system.
  14. ate assembly to timing belt inner cover.
  15. Disconnect A/C lines at compressor.
  16. Remove charge air inlet hose.
  17. Remove the EGR airflow control valve from the intake manifold.
  18. Remove high pressure injection pump to fuel rail high pressure line.
  19. Disconnect high pressure injection pump quantity control valve electrical connector.
  20. Disconnect fuel supply and return lines at high pressure injection pump.
  21. Remove alternator to intake manifold bracket.
21 Remove high pressure injection pump retaining nuts and remove pump.

Care must be taken not to bend the brake vacuum tube when removing high pressure pump.
unquote:


if you learn a short cut to that, please do post it.

Jan 20, 2014 | 2004 Jeep Liberty

1 Answer

Need vacum hose dirgam for subaru impraza 1995


Hi Stephen:
I suggest chgeck this links diagram:
- Vacuum diagram - 1992-95 1.8L fuel injected engine
-
Vacuum diagram - 1995 2.2L fuel injected engine
- Vacuum diagram - 1995 2.2L fuel injected engine (continued)

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Dec 14, 2011 | Cars & Trucks

1 Answer

Need a wiring diagram to install a sterio


Need a wiring diagram for fuel injection system

Jan 16, 2011 | 1995 Pontiac Bonneville

1 Answer

How to change the fuel filter


Fuel Filter The filter should be inspected for external damage and/or leakage at least once a year. The fuel filter should be changed only as necessary. Toyota Motor Corporation recommends replacing the carbureted fuel filters at 15,000 miles and 30,000 miles on fuel injected models. NOTE: Fuel lines and connections, fuel tank vapor vent system hoses and fuel tank bands should be inspected every 60,000 miles or every 36 months. The fuel tank cap gasket should be replaced 60,000 miles or every 72 months.
---
REMOVAL & INSTALLATION Carbureted Engines The fuel filter on carbureted engines is a plastic cylinder with two ports for the fuel. It is usually located in the engine compartment near the charcoal canister.
  1. Using a pair of pliers, expand the hose clamp on one side of the filter, and slide the clamp further down the hose, past the point to which the filter pipe extends. Remove the other clamp in the same manner. Grasp the clamps and slide them up the hose slightly above the filter ends 88271p10.jpg

  2. Grasp the hoses near the ends and twist them gently to pull them free from the filter pipe. Slide the hose off the end of the fuel filter end 88271p11.jpg

  3. Pull the filter from the clip and discard. Be carefull when removing the filter, some fuel may spill out if not held upright 88271p12.jpg
    To install:
  4. Install the new filter into the clip. The arrow must point towards the hose that runs to the carburetor.
  5. Push the hoses onto the filter pipes, then slide the clamps back into position.
  6. Start the engine and check for leaks.
Fuel Injected Engines 1993-97 MODELS
  1. Turn the ignition switch to the LOCK position. Disconnect the negative battery cable and wait at least 90 seconds before proceeding with working on the fuel system. This will depressureize the fuel system. The fuel filter can be hard to locate on these engines 88271pa1.jpg
    Fig. 4: Exploded view of the fuel filter mounting - 1993-97 models 88271g02.gif
    Fig. 5: Disconnect the negative battery cable prior to all fuel system repairs 88271g03.gif
    CAUTION
    Failure to depressurise the fuel system could cause personal injury.
  2. Disconnect the Intake Air Temperature (IAT) sensor wiring.
  3. Loosen the air cleaner hose clamp bolt, the disconnect the four air cleaner cap clips. Fig. 6: Loosen the air cleaner hose clamp bolt 88271g04.gif

  4. Spearate the air cleaner hose from the throttle body, and remove the air cleaner cap together with the air cleaner hose.
  5. Disconnect the EVAP canister hose from the charcoal canister. Fig. 7: Remove both EVAP hoses from the charcoal canister 88271g05.gif

  6. Remove the charcoal canister from the bracket.
  7. Place a suitable container or shop towel under the fuel filter. Remove the union bolt and two gaskets, then slowly disconnect the fuel inlet hose from the fuel filter outlet. Fig. 8: Remove the union bolt and two gaskets from the fuel filter, then disconnect the inlet hose from the filter 88271g06.gif

  8. Using a special wrench 09631-22020 or equivalent, disconnect the inlet pipe from the fuel filter. Remove the two bolts and the filter from the vehicle. Fig. 9: Using a special tool, disconnect the inlet pipe from the fuel filter 88271g07.gif
    Fig. 10: Remove the two filter mounting bolts, then separate the filter from the vehicle 88271g08.gif
    To install:
  9. Install the fuel filter with the two bolts and tighten them to 43 inch lbs. (5 Nm).
  10. Using the special wrench 09631-22020 or equivalent, connect the inlet pipe to the fuel filter. Tighten to 22 ft. lbs. (30 Nm). Using a torque wrench, tighten with a fulcrum length of 11.81 inch (30cm). Install the fuel inlet hose to the filter outlet using new gaskets and union bolt. Tighten to 22 ft. lbs. 30 Nm). Fig. 11: Install the filter inlet hose to the filter outlet, then tighten to 22 ft. lbs. (29 Nm) 88271g09.gif

  11. Install the charcoal canister to the bracket. Connect the two EVAP hoses to the canister.
  12. Connect the air cleaner hose to the throttle body. Install the air cleaner cap together with the air cleaner hose.
  13. Attach the IAT sensor wiring.
  14. Connect the negative battery cable. Start the engine and check for leaks. Reset any various digital equipment such as radio memory and the clock if necessary.
prev.gif next.gif

Nov 08, 2010 | 1993 Toyota Corolla

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

1 Answer

Where is the fuel filter on a turbo desail


Your fuel filter is mounted on the rear of intake manifold, under air cleaner or on rear firewall.
Just a little hint on replacing it, remove your fuel tank cap to release pressure or vacuum in the tank. I'm sending you a diagram the fuel filter assembly so it will make it a little simpler for you to replace your fuel filter. Start by removing the filter element nut. Remove filter element by lifting straight out of filter housing. It is not necessary to drain fuel from filter housing when changing the filter element.
Installation, ensure mating surface between filter element assembly and filter housing is clean. Install new filter element by aligning widest key slot located under element assembly cap with widest key in filter housing assembly.
Tighten element nut by hand. Bleed air from fuel manager/filter assembly. Connect a hose to air bleed valve and place other end of hose in a container.
Disconnect fuel injection pump shutoff solenoid wire. Crank engine for 10 to 15 seconds. Allow starter to cool down for one minute between cranking intervals. Repeat procedure until clear fuel is observed at the air bleed hose.
Close air bleed. Connect injection pump shutoff solenoid wire and reinstall fuel filler cap. Start engine and allow to idle for five minutes. Check fuel manager/filter for leaks.9df1ca0.gif

Oct 03, 2009 | 1994 Chevrolet C/K 2500

2 Answers

Need diagram of fuel injection for 85 4x4 22re


Sounds like you have a vacuum leak somewhere. There may be a stop adjustment on the throttle body, but usually high idles are due to unmetered air entering the system.

Jul 14, 2009 | 1985 Toyota Pickup

Not finding what you are looking for?
1990 Daihatsu Rocky Logo

Related Topics:

386 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...