Question about 1988 Ford Bronco II

1 Answer

TRANSMISSION I WANT TO PUT AN 88 TRANSMISSION IN AN 86 BRONCO 2 BOTH ARE 2.9 STANDARD TRANNY ONE IS A 4X4 ONE IS ONLY A TWO WHEEL DRIVE WILL THIS WORK??

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

The two wheel drive tranny won't work because it will be longer. The tranny that came out of the 4 wheel drive is shorter and the transfer case bolts to the rear of the tranny thus it has a shorter output shaft and a different spline to accommodate the transfer case. You need to find the correct tranny unless you want to change the internals from one tranny to the other.

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 bronco ii won't go into 4x4 or low range


ON LEVEL GROUND
With the transmission selector in "park", start the motor.
With your foot on the brake pedal (steady-constant pressure), move the transmission selector gear to neutral- then turn the 4 X 4 selector knob to 4-wheel drive high. Wait for the 4 X 4 engagement.
Once it is in 4-wheel drive high, with the transmission selector still in neutral, quickly pump the brake peddle twice, keeping you foot on the brake pedal on the second pump, turn the 4 X 4 selector knob from high range to low range. The transfer case should then change from 4-wheel drive high to low.
Electronics being what they are, you sometimes have to repeat the process. You may even have to inch forward or backward.
[I have an '01 Excursion and an '05 F250 with 4 X 4 on the fly...I miss my '97 F250 with the manual 4 X 4 shift on-the-floor!]
Anyway, check the fuse panel for any blown fuses.
Double check to make sure that the problem is not just blown 4 X 4 lights on the instrument cluster. With the nob turned to 4-wheel drive, have a second person- a spotter, check to see if the drive shaft to the transfer case is moving. If it isn't, you have to delve into the troubleshooting process.
Check the solenoids, vacuum hoses, vacuum actuator, and transmission range sensor on the transfer case. .

Nov 27, 2013 | 1989 Ford Bronco II

1 Answer

Can i put a 84 bronco 2 tranny mazda type 14 bolt pan in a 88 bronco 2 that originally had a 12 bolt pan both 4wd


well if it is a 1984 tranny it is a toyo koygo tk4 or tk5, which if mounted in the 84 bronco the transmission sets at a tilt, which means that the transmission crossmember bolts into the frame at a angle.. the mazda tranny was used in 88-90 the transmission crossmember sets straight across and bolts on to the frame on each side with one bolt.. with some major fabricating it is possible but to simply change out nope wont fit..

Jan 28, 2011 | 1988 Ford Bronco II

1 Answer

How do I remove the transmission of my 1989 Bronco II (2) 4x4 ?


Well first you have to remove the rear drive shaft, then the transffer case, then you can unbolt the flex plate from the torque convertor, and unbolt tranny from engine.

There's alot more to it than that, but thats the basics in a nutshell.

Nov 13, 2009 | 1989 Ford Bronco II

1 Answer

Transmission fluid leaking back, 1988 Ford Bronco


your output seal on the tranny or input seal on your transfer case is bad. you have to pull your transfer case to tell. this is a pretty straight forward job. block wheels. put transfer case in neutral. drop front and rear drive lines.diconnect transfer case shift linkage. there is a short commponent connecting the trans to the transfer case. the bolt on either end face each other. remove the bolts to the transmission. the transfer case is heavier than it looks, i suggest getting help. pull back on the transfer case until it will drop down. it will pull out a bit because of the trans output shaft. replace what will probibly turn out to be the tranny output shaft seal and reassemble in reverse order.

Nov 06, 2009 | 1988 Ford Bronco II

2 Answers

The auto tranny is not shifting and is reving up way to high!


try shifting it manually from low,let rpms rise,then 2nd,let rpms rise,then to drive and see what happens.It could be bad drive clutches in the transmission but could be a sticky valve body in the transmission,if it does work by shifting manually add 1\2 pint of dot#3 brake fluid to the transmission fluid to assist in cleaning the pistons in the valve body and seals and to help lubricate parts and seals

Apr 25, 2009 | 1990 Ford Bronco

1 Answer

Transmission type


any transmission that is for a straight six engine. doesn't matter what car it comes out of as long as it is hooked to the same engine it will bolt up to yours.

Mar 10, 2009 | 1990 Ford Bronco II

1 Answer

Tranny?


I don't know what you are making reference to. There are no nose cones on tranny's. Maybe you are inquiring about the tail shaft ? You can't change the tail shaft unless you change the main shaft in the tranny.

Feb 17, 2009 | 1995 Ford Bronco

3 Answers

Hello, 1986 Toyota 4X4 Truck 22R carb engine manual transmission. My son was driving it and the rear wheels locked up. Driving in 2 High mode. He got the truck pulled over to the side of the road using 4X4...


I've seen a similar issue on other transmissions where the shifter slips out of the slots in the shift forks, either due to shifter bushing wear or just general wear on tte trans. It can usually be remedied at least temporarily by popping the shifter top off the trans and resetting the forks all back to nuetral and then reinserting the shifter. It gets jammed when two forks are trying to engage two different gear sets.
On one of the 4x4 sites, they tell you how to replace the shifter bushings, cheap fix if you are lucky.
Good luck.

Dec 09, 2008 | 1986 Toyota Pickup 4WD

1 Answer

Bronco tranny wont shift out of first


sounds like you burnt it up. how long did u drive it like that?

Nov 04, 2008 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...