Question about 1992 Honda Accord

1 Answer

Is a 16 valve afe honda accord a 2.0 engine

I just want to know if a 16 valve afe is a 2.o

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 92 Accord and its a 16 valve with sohc and its a 2.2 liter 4 cylinder

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 honda accord vtech timing belt marks


The Honda F23 series engine is a 2.3 liter, all aluminum block, 16 valve, Single Overhead Camshaft (SOHC) motor used in the Honda Accord (1994 - 2002) and Acura Cl (2.3). Timing belt failure may result in either the intake or exhaust valves bending after contacting the pistons. If the belt has broken, a Compression Leakage test is advised to determine if the valves require replacement. Compression leakage from any of the cylinders (indicating bent valves) will require the removal of the cylinder head. An inspection and rebuild of the head by a reputable automotive machine shop is recommended in lieu of doing it yourself. This DIY article only covers belt replacement. The belt replacement interval is either 90,000 or 105,000 miles based on the specific model year. Check the owner's manual for the specific service interval. If the mileage is below the threshold but the vehicle is over 7 years old, consider performing a replacement as preventative maintenance (PM). Timing belts cannot be visually inspected for wear. Moreover, a visual inspection would require the removal of the timing belt cover which in itself is time consuming and better spent working on replacement. A typical timing belt component kit consists of: 1. Timing Belt 2. Balance Shaft Belt. 3. Timing Belt Tensioner Pulley. 4. Balance Shaft Tensioner Pulley

Sep 28, 2016 | 1999 Honda Accord

1 Answer

What is the map sensor code for a 1992 honda accord


1. yes a 1992 Honda accord has a map sensor and what accord do you have engine wise ?? because theres different codes 2. it could be a idle air control valve because if they get dirty they can cause the car to rev high low or even stall and cause the car to run crappy.

Apr 23, 2014 | 1999 Honda Accord

1 Answer

Adjustment valve


Not sure I understand what you are asking here.

Apr 16, 2014 | 2006 Honda Accord

1 Answer

Where is the IAT sensor location on honda accord 1986


what engine, I4 or V6? what country, like 10 engines world wide.?
and North America received the A20A1 and A20A3.
got and A20?
A1 is carb engine
A3 is EFI. so this must be yours, if in USA< are you?

The A20A3
IAT (
is the diagnostic light failing for IAT? CODE 10? (map based engine, it is)
i googled first. (if failed)
its in the FSM
http://hondatech.info/downloads/Auto/Manuals/Accord/

or at alldata.com
v6, its dead center of intake plenum. just behind EGR valve.
I4 its at.... see page 12-2 in FSM, its on end if engine
standing in front of engine, ,point to right if engine end/
then back a tad and bingo. is in the link above. page 12-2 and 12-36
in the FSM. page 36 is how to test it in hot water.
page 2 acutal for A20A3
now you have the book.
http://www.fixkick.com/look/odds-ends/honda/accord/A20-A3-IAT.JPG




Dec 17, 2013 | 1986 Honda Accord

1 Answer

Easiest way to check timing belt


If you simply want to check the timing belt condition, then remove the plastic cover and visually inspect it. If you have the 5 sfe engine, the timing belt cover is a 2 piece assembly, upper and lower. if you have the 7 afe or 4 afe engine the timing cover is 3 pieces and to inspect the top of the timing belt you must remove the 4 nuts holding the valve cover down and the 2 bolts holding the wire loom. remove the whole valve cover. to inspect timing belt condition.

Aug 06, 2011 | 1990 Toyota Corolla

2 Answers

Lekage of oil from timing belt side/from crank seal


Usually the 8th vin number is the year, so "3" means 1993. Your Accord is a 1993. You need to request the front main oil seals for your 1993 Accord. they will request the engine size example 2.2 L.
Goodluck.

Aug 28, 2009 | 1990 Honda Accord

2 Answers

Replacing head gasket


start in middle and work outwards left right left right with the bolts ,torque ??easy start with a rachet which will allow about 40lbs then a snap on knuckle bar till you can feel bolts stretch.as to type of head???is it 8 valve or 16??16 valve dearer to do

Jan 13, 2009 | 1988 Honda Accord 4 Door

1 Answer

How to tell what engine


There were two engines fitted to the US model of that year.
4cyl 2.2L 2156cc L4
6cyl 2.7L 2675cc V6

Aug 31, 2008 | 1995 Honda Accord

1 Answer

1992 honda accord ex timing belt


yes this engine is a interference engine. Make sure you did not bend the valves when it boke.

Jul 21, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...